Współpraca
SZTUKA
Piękno i dobre samopoczucie
RZEMIOSŁO
KULTURA I HISTORIA
ROZRYWKA
ŚRODOWISKO
JEDZENIE I NAPOJE
INŻYNIERIA ODWROTNA
NAUKI
LEKKOATLETYKA
TECHNOLOGIA
URZĄDZENIA DO NOSZENIA
Rotary-Tub Spout Churn: A Friction Wheel Spins the Tub, a Fixed Spout Catches the Climbing Cream and Jets It Into a Basket
Buttercup

Autor

Buttercup

11. listopad 2026IE
9
0
0
0
0

Rotary-Tub Spout Churn: A Friction Wheel Spins the Tub, a Fixed Spout Catches the Climbing Cream and Jets It Into a Basket

Clark Wright and William Phelps of Sycamore, Illinois, received US 28,802, dated 19 June 1860, for a churn. The tub itself spins, carried on a plate that rests on a crank-turned friction wheel. The cream climbs the side until a flange stops it, where a fixed spout catches it and shoots it into a perforated basket hung loose in the middle; the butter collects in the basket while the milk runs out through its holes and climbs again. The patent gives no sizes; every size here is ours.
Zaawansowany
About 2 days, plus printing

Instrukcje

1

How fast the tub must turn for the cream to climb

Wczytywanie notatnika Jupyter…
2

Cream flung outward and jetted, three months before

Sangster spins paddles to fling the cream. Wright and Phelps spin the whole tub.
3

Read US 28,802

"A quantity of cream being placed in the tub F, and the latter rapidly rotated by means of the crank D and friction wheel E, the cream ascends the sides of the tub by centrifugal force until arrested by the flange f and being caught by the spout K is deflected inward and projected in a forcible and continuous stream into the basket H, causing violent agitation in the body of cream as well as friction as it flows out through the apertures in the basket."
4

Print the basket H

Perforated cone basket 160 mm across at the top, 130 at the bottom, 150 tall, with a hub bored 12.6 mm. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Plik projektowySTLCC0 - Free
5

Print the spout K

Curved spout 40 mm wide, its mouth at the wall turning inward over 55 mm, with a hanger and a clamp that slides along the bar I. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Plik projektowySTLCC0 - Free
6

Base A, standard B, spindle G and plate g

Make a hardwood base 520 x 560 mm. Screw a hardwood standard 60 mm square in its middle, its top bored 16.6 mm to take a 16 mm stainless spindle. Cut a plywood disk plate 300 mm across, fix the spindle in its centre, and screw the bucket down on it, sealing the screw heads inside with silicone. Screw a ring of HDPE sheet, 26 mm wide, inside the bucket 340 mm up as the flange f, and a hardwood socket bored 12.6 mm in the floor's centre.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego2 sztuk
Płyta sklejkowaPłyta sklejkowa1 sztuka
Pręt ze stali nierdzewnejPręt ze stali nierdzewnej1 sztuka
Wiadro 20-litroweWiadro 20-litrowe1 sztuka
Płyta HDPEPłyta HDPE1 sztuka
Klocek z drewna twardegoKlocek z drewna twardego1 sztuka
Klej do drewnaKlej do drewna1 sztuka
Wkręty do drewnaWkręty do drewna16 sztuk
Uszczelniacz silikonowyUszczelniacz silikonowy1 sztuka

Potrzebne narzędzia:

Pilarka stołowaPilarka stołowa
WyrzynarkaWyrzynarka
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Zestaw wierteł łopatkowychZestaw wierteł łopatkowych
Ścisk stolarski listwowyŚcisk stolarski listwowy
Zestaw wkrętakówZestaw wkrętaków
7

Friction wheel E, shaft C and crank D

Turn a hardwood wheel E 220 mm across with its rim rounded in section, as the patent's "regular convexity". Bolt two hardwood bearing blocks to the base so a 16 mm stainless shaft C runs straight out from under the spindle, at a height where the wheel, fixed on its inner end 50 mm from the spindle, just carries the plate. The shaft must point at the spindle, so the wheel rolls on the plate without scrubbing. Fix the wheel on the shaft, and a hardwood crank D with a dowel handle on its end; hold it with collars.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Pręt ze stali nierdzewnejPręt ze stali nierdzewnej1 sztuka
Kołki z twardego drewnaKołki z twardego drewna1 sztuka
Klej do drewnaKlej do drewna1 sztuka
Śruba zamkowaŚruba zamkowa4 sztuk
Nakrętka skrzydełkowaNakrętka skrzydełkowa4 sztuk
Shaft CollarShaft Collar2 sztuk

Potrzebne narzędzia:

Tokarka do drewnaTokarka do drewna
Papier ściernyPapier ścierny
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Piła do metaluPiła do metalu
Klucz nastawnyKlucz nastawny
8

Standards J, bar I, pin, basket H and spout K

Stand two hardwood standards J 30 x 30 mm either side of the bucket and join their tops with a bar I across it, bored 12.6 mm over the centre. Drop a 12 mm stainless pin through the bar into the floor socket and slide the basket onto it so it turns freely. Clip the spout's clamp on the bar so its mouth sits just under the flange, close to the wall, facing against the tub's turn; slide it in or out to suit.

Materiały do tego kroku:

Deska z drewna liściastegoDeska z drewna liściastego1 sztuka
Pręt ze stali nierdzewnejPręt ze stali nierdzewnej1 sztuka
Wkręty do drewnaWkręty do drewna6 sztuk
Klej do drewnaKlej do drewna1 sztuka
Filament PETGFilament PETG1 sztuka

Potrzebne narzędzia:

Drukarka 3D z filamentem (FDM)Drukarka 3D z filamentem (FDM)
Pilarka stołowaPilarka stołowa
Wiertarko-wkrętarka akumulatorowaWiertarko-wkrętarka akumulatorowa
Zestaw wiertełZestaw wierteł
Piła do metaluPiła do metalu
Miara zwijanaMiara zwijana
9

The build in 3D

FreeCAD model of this build, the tub cut open: the spindle and plate on the friction wheel and crank, the flange, the basket on its pin, the spout hanging from the bar, and the standards.
Plik projektowyBLENDCC0 - Free
10

Churn

Pour about 5 litres of heavy cream at about 15 °C, checked with the thermometer, into the tub around the basket. Turn the crank briskly, timing it, until the cream climbs to the flange and runs from the spout into the basket. Keep on until the butter has gathered in the basket. Lift out the pin and basket with the butter, pour off the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

Materiały do tego kroku:

Śmietanka kremówkaŚmietanka kremówka5 l
Sól morska gruboziarnistaSól morska gruboziarnista1 sztuka
WodaWoda1 sztuka

Potrzebne narzędzia:

Termometr z sondą pozostawianą w potrawieTermometr z sondą pozostawianą w potrawie
StoperStoper
Cyfrowa waga kuchennaCyfrowa waga kuchenna
Duża misa ze stali nierdzewnejDuża misa ze stali nierdzewnej
11

Troubleshooting

Rotary-tub churn troubleshooting.

Flow

Loading...
12

History and honest limits

**Clark Wright** and **William Phelps** of Sycamore, DeKalb County, Illinois, US 28,802, 19 June 1860, "Churn". They claimed the rotary tub, stationary spout and basket together. Their wheel and plate meet as two crossed discs, the wheel's rounded rim avoiding both side thrust and broad rubbing faces. Every size here is ours.

Materiały

17

Wymagane narzędzia

17

Pliki projektowe

3
  • wright-phelps-rotary-tub-spout-basket-churn-basket-h.stlSTLCC0
  • wright-phelps-rotary-tub-spout-basket-churn-spout-k.stlSTLCC0
  • wright-phelps-rotary-tub-spout-basket-churn.blendBLENDCC0

CC0 Domena publiczna

Ten plan jest udostępniany na licencji CC0. Możesz go swobodnie kopiować, modyfikować, rozpowszechniać i wykorzystywać do dowolnych celów, bez konieczności uzyskiwania zgody.

Wesprzyj Makera kupując produkty przez jego plan, za co zarabia Prowizja Makera ustalony przez sprzedawców, lub stwórz nową iterację tego planu i dołącz go jako połączenie w swoim własnym planie, aby dzielić się przychodami.

Dyskusja

(0)

Zaloguj się aby dołączyć do dyskusji

Ładowanie komentarzy...