ИСКУССТВО
КРАСОТА И ЗДОРОВЬЕ
РЕМЕСЛО
КУЛЬТУРА И ИСТОРИЯ
РАЗВЛЕЧЕНИЯ
ЭКОЛОГИЯ
ЕДА И НАПИТКИ
ОБРАТНАЯ ИНЖЕНЕРИЯ
НАУКИ
СПОРТ
ТЕХНОЛОГИИ
НОСИМЫЕ УСТРОЙСТВА
Spring-Wire Twin Dash Churn: Two Hinged Dashes Rocked by a Sprung Wire on a Crank
Dugdale made the link between crank and dashes a spring.
Samuel G. Dugdale of Richmond, Indiana, received US 8,219, dated 15 July 1851, for a churn: a water-tight box 16 inches long, nine wide and twelve deep, with two perforated dashes seven by six inches hung by hooks on staples three inches above the bottom at each end. A shaft with a three-inch crank turns in grooves in the box's edges, held down by the lid; an elastic wire bent round the crank, closed into an eye, has its ends hooked into staples on the dashes, "in such a manner that it will accommodate itself to the opening and closing of the same."
This rung works out the dashes' swing, then prints the two dashes and shaft bearings, bends the spring wire, and makes butter.
Начинающий
About 2 hours, plus printing
Инструкции
1
1
The dashes' swing
The dashes' swing
Загрузка блокнота Jupyter…
2
2
Two dashers worked from one motion before it
Two dashers worked from one motion before it
The embedded blueprint links two dashers with levers. Dugdale links his two hinged dashes to one crank with a single sprung wire.
3
3
Read US 8,219
Read US 8,219
"It will be noticed, also, that when the handle is raised perpendicular, the crank to which the wire is attached will be parallel to it, and the ends of the wire attached to the dashers, will be extended, and as the handle is turned from you the springs act upon the dashers tending to force them down, thereby facilitating the operation."
4
4
Print the parts
Print the parts
Print two perforated dashes with their hooks and staple and two shaft bearings. Print in PETG at 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
Материалы для этого шага:
Филамент PETG1 штукаНеобходимые инструменты:
3D-принтер FDM5
5
Print the dash
6
6
Print the shaft bearing
Print the shaft bearing
The shaft bearing, printed as step 4 describes.
7
7
Box and staples
Box and staples
Take a food-safe box about 240 × 135 × 180 mm, about three fifths of his. Screw a stainless screw-eye into each end 30 mm above the bottom as the staples, and hang a dash on each by its hooks, holes toward the middle. Screw the bearings to the box's long edges at the middle.
Материалы для этого шага:
Ёмкость для хранения пищевого качества1 штука
Шуруп по дереву #8 x 1"1 штукаНеобходимые инструменты:
Аккумуляторная дрель
Набор свёрл
Набор отвёрток8
8
Crank and spring wire
Crank and spring wire
Bend a 6 mm steel rod into a shaft with a 45 mm crank in the middle and a handle at one end, and lay it in the bearings. Bend spring-steel wire once round the crank pin into an eye and hook its two ends into the dashes' staples, so the wire is a little stretched with the crank up.
Материалы для этого шага:
Круг из низкоуглеродистой стали1 штука
Пружинная стальная проволока1 штукаНеобходимые инструменты:
Разводной ключ
Ножовка по металлу9
9
The build in 3D
The build in 3D
FreeCAD model of this build, not of the patent: the box with one side off to show the two perforated dashes hooked to the ends, the spring wire from the crank to their inner ends, and the shaft.
10
10
Crank and make butter
Crank and make butter
Let the heavy cream stand until it reaches about 15 °C, checked with the thermometer. Pour in 2 litres, enough to cover the dashes. Fit the lid over the shaft and turn the handle steadily; time until the butter comes. Pour off the buttermilk, add cold water, churn a little and pour off again until it runs clear; work in a pinch of salt and weigh the butter.
Материалы для этого шага:
Жирные сливки2000 мл
Крупная морская соль1 штука
Вода1 штукаНеобходимые инструменты:
Термометр с оставляемым щупом
Секундомер
Цифровые кухонные весы
Большая миска из нержавеющей стали11
11
Dashes that jump off, a wire that kinks
Dashes that jump off, a wire that kinks
Spring-wire twin dash troubleshooting.
Flow
Loading...
12
12
History and honest limits
History and honest limits
**Samuel G. Dugdale** of Richmond, Wayne County, Indiana, received US 8,219, dated 15 July 1851. His dashes were half an inch thick with holes leaving 2½ inches plain at the hung ends; collars kept the shaft from slipping; it could be turned by a handle or a pinion on a driving wheel. He claimed "the application of the spring wire ... which connects the crank with the dashers."
**Honest limits.** A food-safe box at about three-fifths scale and printed dashes stand in for his. FDM prints hold food in their layer lines, so wash well and replace when worn. Your times and weights are the result.
Материалы
8- 1 штукаЗаполнитель
- Заполнитель
- 1 штукаЗаполнитель
- Заполнитель
- 1 штукаЗаполнитель
- 2000 млЗаполнитель
- 1 штукаЗаполнитель
- 1 штукаЗаполнитель
Требуемые инструменты
10- Заполнитель
- 1 vendor sell this, none ship to you yetЗаполнитель
- Заполнитель
- Заполнитель
- Заполнитель
- Заполнитель
- Заполнитель
- Заполнитель
- Заполнитель
- Заполнитель
Файлы дизайна
3По этому чертежу делают
Связанные чертежи
Эти чертежи делятся знаниями — техники, материалы или принципы
Double-Dasher Lever Churn: Swing One Lever, One Dasher Rises as the Other Falls
от Woody
Деревообработка
36
0
0
0
0
0
Twin-Plunger Air-Chamber Churn: Two Plungers Throw the Cream Through a Middle Chamber
от Emma
ЕДА И НАПИТКИ
32
0
0
0
0
0
Churning Butter from Cream — The 5,000-Year-Old Fat Separation
от TheChef
РЕМЕСЛО
54
0
0
0
0
0
CC0 Общественное достояние
Этот чертёж выпущен под лицензией CC0. Вы можете свободно копировать, изменять, распространять и использовать эту работу в любых целях без запроса разрешения.
Поддержите мейкера, покупая товары через его чертёж, где он получает Комиссию мейкера установленную продавцами, или создайте новую итерацию этого чертежа и включите его как связь в свой чертёж для распределения дохода.