ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Agitated Mixing Tank: the Cone-Bottom Light-Oil Agitator (Bell, 1923)
Forge

สร้างโดย

Forge

4. พฤศจิกายน 2026NO
9
0
0
0
0

Agitated Mixing Tank: the Cone-Bottom Light-Oil Agitator (Bell, 1923)

The refinery agitator for washing oil with acid, soda and water: a lead-lined riveted steel tank with a cone bottom, an air line that blows up through the charge to mix it, a spray header for wash water, and draw-offs at the tip of the cone for sludge and finished oil. Variable: capacity, 160 to 5,000 barrels. Bell's Fig. 87 is 1,000 barrels: 25 ft inside diameter, 25 ft shell, 7 ft 6 in cone, 32 ft 6 in overall. Source: H. S. Bell, American Petroleum Refining (1923), pp. 195-200. Unknown: plate thickness. Picture: Fig. 87 of the book.
ผู้เชี่ยวชาญ
Unknown

คำแนะนำ

1

Set the foundation and columns

Choose the capacity (160 to 5,000 barrels). Rest the tank on lugs on steel or concrete columns, fireproofing steel ones; the older way of extending the shell down with gussets under the cone is heavy. Fig. 87 stands on concrete footings with a tile drain under the cone tip.

วัสดุสำหรับขั้นตอนนี้:

คอนกรีตคอนกรีต1 footings, columns

เครื่องมือที่ต้องใช้:

ขนาดที่ไม่ทราบขนาดที่ไม่ทราบ
2

Build the shell and cone

Rivet a cylindrical shell (Fig. 87: 25 ft inside, 25 ft high) onto a cone bottom pitched no more than 4 in per foot from the horizontal for light oils; sludge still runs out at that slope. With a tight lead lining the shell need not be caulked; leave out an occasional rivet so lining leaks show. Not given: plate thickness.

วัสดุสำหรับขั้นตอนนี้:

แผ่นเหล็กกล้าละมุนแผ่นเหล็กกล้าละมุน1 shell, cone
เหล็กฉากเหล็กกล้าละมุนเหล็กฉากเหล็กกล้าละมุน1 top and cone angles
หมุดย้ำเหล็กกล้าหมุดย้ำเหล็กกล้า1 ชิ้น

เครื่องมือที่ต้องใช้:

เครื่องปั๊มเจาะเครื่องปั๊มเจาะ
ค้อนย้ำหมุดค้อนย้ำหมุด
3

Fit a low roof with relief

Use a low globe roof, not the old hemispherical 'gas bag', with plenty of explosion hatches; even 10 % relief area has not always saved a roof. Bell's preferred form (Fig. 89) has two roof segments that lift in an explosion and fall back to smother the fire.

วัสดุสำหรับขั้นตอนนี้:

แผ่นเหล็กกล้าละมุนแผ่นเหล็กกล้าละมุน1 roof
หมุดย้ำเหล็กกล้าหมุดย้ำเหล็กกล้า1 ชิ้น

เครื่องมือที่ต้องใช้:

ค้อนย้ำหมุดค้อนย้ำหมุด
4

Pipe the air, spray and draw-offs

Run a 4 in air line down to the cone tip; the blast needs at least 200 to 250 cu ft of free air per minute per 1,000 barrels, at just enough pressure to beat the oil head. Across the top fit a 3 in header with 1 in spray pipes drilled with 1/8 in holes at 2 in centres. At the cone tip fit valved rundown, sludge and drain lines.

วัสดุสำหรับขั้นตอนนี้:

ท่อเหล็ก (ผนังหนา ปลายเกลียว)ท่อเหล็ก (ผนังหนา ปลายเกลียว)1 4 in air, 3 in header, 1 in sprays
วาล์วประตูน้ำวาล์วประตูน้ำ3 rundown, sludge, drain

เครื่องมือที่ต้องใช้:

สว่านมือสว่านมือ
เครื่องเป่าลมเครื่องเป่าลม
5

Line it with lead

Weak acid from the washes eats steel, so line it with lead: 8 lb per sq ft on the shell, 10 lb on the cone, or 6 % antimony lead half a pound lighter. Don't just hang it from the top angle: agitation makes a loose lining creep and crack. Hold it with lead-covered steel straps about 8 ft apart, bolted through the shell, and bring the lining out through the draw-off neck.

วัสดุสำหรับขั้นตอนนี้:

แผ่นตะกั่วแผ่นตะกั่ว1 8 lb shell, 10 lb cone
เหล็กแบนกล้าละมุนเหล็กแบนกล้าละมุน1 straps
สลักเกลียวหัวหกเหลี่ยม - เกรด 8.8สลักเกลียวหัวหกเหลี่ยม - เกรด 8.81 ชิ้น

เครื่องมือที่ต้องใช้:

ค้อนไม้ค้อนไม้
คบเพลิงคบเพลิง

วัสดุ

9

เครื่องมือที่จำเป็น

7

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...