การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Ski Sled: Two 10 ft Ash Ski Runners With a Rocker, Under a Three-Board Top (Boy Mechanic, 1919)
Woody

สร้างโดย

Woody

13. พฤศจิกายน 2026NO
6
0
0
0
0

Ski Sled: Two 10 ft Ash Ski Runners With a Rocker, Under a Three-Board Top (Boy Mechanic, 1919)

George J. Egelberg's ski sled from The Boy Mechanic, Book 3 (1919): "built low and wide so that it will not tip easily", on two 10 ft by 6 in ash runners boiled and bent like skis, set on knee blocks with a slight rocker, and topped with three 6 in boards.
ระดับกลาง
About 2 days

คำแนะนำ

1

His sizes, and the rocker

กำลังโหลดสมุด Jupyter…
2

Read The Boy Mechanic, Book 3

"The skis, or runners, are cut 10 ft. long and 6 in. wide, from 1-in. ash boards that are straight-grained."
3

Thin the bend

Cut two runners 10 ft long and 6 in wide from straight-grained 1 in ash. Where the curve will be, plane about 1/4 in off the upper side, but not at the very tip, so the skis bend more easily.

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง2 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยมือเลื่อยมือ
กบไสไม้กบไสไม้
ตลับเมตรตลับเมตร
ดินสอดินสอ
4

Boil and bend

If steaming is not handy, boil the skis with at least 1-1/2 ft of the points under water and the vessel covered so little steam escapes, for at least one hour. Take them out, put them side by side in the bending blocks at once and bend with slow, even pressure; weight the long ends and leave them 8 or 10 hours to dry. Sharpen the points after bending.

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้สนแผ่นไม้สน1 ชิ้น

เครื่องมือที่ต้องใช้:

หม้อใบใหญ่หม้อใบใหญ่
แคลมป์แบบบาร์แคลมป์แบบบาร์
กบไสไม้กบไสไม้
5

Set the blocks and top

For a slight rocker, make the centre knee block 6 in high and the two end blocks 5-1/2 in. Run a 1/4 in flat-head bolt through the ski, the block and the cross strip, countersinking the heads in the running surface. Make the top of three 6 in boards fastened to the crosspieces, and brace the ski tips with a 2 in strip.

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง1 ชิ้น
แผ่นไม้สนแผ่นไม้สน3 ชิ้น
สลักเกลียวหัวกลมสลักเกลียวหัวกลม6 ชิ้น
แหวนรองแบนแหวนรองแบน6 ชิ้น
สกรูไม้สกรูไม้1 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยมือเลื่อยมือ
สว่านมือสว่านมือ
ชุดดอกลบมุมรูชุดดอกลบมุมรู
ค้อนค้อน
6

Troubleshooting

Ski sled troubleshooting.

Flow

Loading...
7

History and honest limits

From "A Ski Sled" by George J. Egelberg, in **The Boy Mechanic, Book 3**, Popular Mechanics, 1919 (Project Gutenberg 71856; checked on the archive.org scan boymechanic0003unse, p. 41). The bending-block shape and knee pieces come from his drawing. The tools and metric figures are ours.

วัสดุ

5

เครื่องมือที่จำเป็น

9
  • ตัวยึดตำแหน่ง
  • ตัวยึดตำแหน่ง
  • 1 vendor sell this, none ship to you yet
    ตัวยึดตำแหน่ง
  • 1 vendor sell this, none ship to you yet
    ตัวยึดตำแหน่ง
  • ตัวยึดตำแหน่ง
  • ตัวยึดตำแหน่ง
  • ตัวยึดตำแหน่ง
  • ตัวยึดตำแหน่ง
  • ตัวยึดตำแหน่ง

พิมพ์เขียวนี้สร้าง

บลูพริ้นท์ที่เกี่ยวข้อง

บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...