การทำงานร่วมกัน
ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Craftsman Leather Billfold: Two Cardboard Patterns, Silk Lining and Saddle-Stitched Waxed Silk (Boy Mechanic, 1919)
Tex

สร้างโดย

Tex

13. พฤศจิกายน 2026FO
15
0
0
0
0

Craftsman Leather Billfold: Two Cardboard Patterns, Silk Lining and Saddle-Stitched Waxed Silk (Boy Mechanic, 1919)

Livingston Haviland's billfold from The Boy Mechanic, Book 3 (1919): two leather body parts cut to stiff-cardboard patterns (13-1/4 and 8-3/16 by 4-1/4 in), lined with skiver or silk moire, folded into two card pockets and a money compartment, glued, and hand-sewn with heavy waxed silk 3/16 in from the edges.
ระดับกลาง
About 1 day

คำแนะนำ

1

His patterns in centimetres

กำลังโหลดสมุด Jupyter…
2

Read The Boy Mechanic, Book 3

"The making of a billfold is easily within the range of an amateur in leather work, who will observe the instructions carefully." Seal, morocco, pigskin and ooze sheep are all satisfactory.
3

Cut the patterns and the leather

Cut two patterns of stiff cardboard (Fig. 1). Body part No. 1: 13-1/4 by 4-1/4 in, with fold lines at 2-1/2, 2-5/8, 3, 2-5/8 and 2-1/2 in, and each end (A, B) cut in with 1/2 in radius arcs, set in 1/4 in. Body part No. 2: 8-3/16 by 4-1/4 in, with fold lines at 2-19/32, 3 and 2-19/32 in. Lay each pattern on the leather and trim the leather even with it, guiding the knife with a metal straightedge, on a close-grained hardwood board or a piece of sheet zinc.

วัสดุสำหรับขั้นตอนนี้:

หนังหมูฟอกหนังหมูฟอก1 ชิ้น
แผ่นแบบจากกระดาษแข็งแผ่นแบบจากกระดาษแข็ง1 ชิ้น

เครื่องมือที่ต้องใช้:

ดินสอดินสอ
ไม้บรรทัดไม้บรรทัด
บรรทัดเหล็กตรวจความตรงบรรทัดเหล็กตรวจความตรง
มีดคัตเตอร์งานประดิษฐ์มีดคัตเตอร์งานประดิษฐ์
แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง
แผ่นสังกะสีแผ่นสังกะสี
4

Line the parts

Cut linings slightly larger than the patterns. Skiver is glued all over with a good, pliable leather glue that will not crack the leather; smooth it on gently without stretching, or the leather may buckle, and dry it under a light weight. Silk moire is glued with a thin stripe round the edges only, left to overhang, and trimmed off neatly when dry.

วัสดุสำหรับขั้นตอนนี้:

ผ้าไหมผ้าไหม1 ชิ้น
กาวติดหนังกาวติดหนัง1 ชิ้น

เครื่องมือที่ต้องใช้:

กรรไกรกรรไกร
มีดคัตเตอร์งานประดิษฐ์มีดคัตเตอร์งานประดิษฐ์
5

Glue and fold

Fold part No. 1 to form the back and the two card pockets. Apply stripes of glue as shown in Fig. 3, drop part No. 2 (the money compartment) into place, and fold the ends of No. 1 over on the dotted lines. Weight the billfold and let the glue dry.

วัสดุสำหรับขั้นตอนนี้:

กาวติดหนังกาวติดหนัง1 ชิ้น

เครื่องมือที่ต้องใช้:

เครื่องมือแกะลายหนังเครื่องมือแกะลายหนัง
6

Mark and punch the stitching

Draw a straight line with a blunt-point tool along the edges to be sewn, 3/16 in from them. Mark the stitch spacing for an inch on a strip of paper and transfer it along the line. Punch the holes on a pine board with a diamond-pointed awl held vertical (D); back the open ends with strips of cardboard while punching.

เครื่องมือที่ต้องใช้:

เครื่องมือแกะลายหนังเครื่องมือแกะลายหนัง
ไม้บรรทัดไม้บรรทัด
เหล็กหมาดเย็บพื้นเหล็กหมาดเย็บพื้น
แผ่นไม้สนแผ่นไม้สน
แผ่นแบบจากกระดาษแข็งแผ่นแบบจากกระดาษแข็ง
7

Sew and finish the edges

Sew with heavy waxed silk matching the leather, by hand or with the work clamped between two boards. Thread a needle on each end, start both from the right side (E), pass the needle from the first hole through the second (F) and, with the needles in position (G), continue this stitch. Tie the ends neatly. Trim the edges and tool them smooth with a suitable metal tool or rod, heated moderately, applying water with the fingertip.

วัสดุสำหรับขั้นตอนนี้:

ด้ายไหมด้ายไหม1 ชิ้น
ขี้ผึ้งขี้ผึ้ง1 ชิ้น

เครื่องมือที่ต้องใช้:

เข็มเย็บอานม้าสองเล่มเข็มเย็บอานม้าสองเล่ม
กรรไกรกรรไกร
มีดคัตเตอร์งานประดิษฐ์มีดคัตเตอร์งานประดิษฐ์
เหล็กเส้นกลมเหล็กกล้าละมุนเหล็กเส้นกลมเหล็กกล้าละมุน
8

Troubleshooting

Billfold troubleshooting.

Flow

Loading...
9

History and honest limits

From "A Craftsman Leather Billfold" by Livingston Haviland, in **The Boy Mechanic, Book 3**, Popular Mechanics, 1919 (Project Gutenberg 71856; checked on the archive.org scan boymechanic0003unse, pp. 446-447). He does not give the number of stitches to the inch or what waxes the silk (beeswax is ours). Pigskin is one of his four leathers. The tools and metric figures are ours.

วัสดุ

6
  • ตัวยึดตำแหน่ง
  • ตัวยึดตำแหน่ง
  • 1 ชิ้น
    ตัวยึดตำแหน่ง
  • ตัวยึดตำแหน่ง
  • 1 ชิ้น
    ตัวยึดตำแหน่ง
  • 1 ชิ้น
    ตัวยึดตำแหน่ง

เครื่องมือที่จำเป็น

13

บลูพริ้นท์ที่เกี่ยวข้อง

บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...