ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Horizontal Cylinder Still: the Riveted Fire Still (Bell, 1923)
Forge

สร้างโดย

Forge

4. พฤศจิกายน 2026NO
8
0
0
0
0

Horizontal Cylinder Still: the Riveted Fire Still (Bell, 1923)

The refinery's direct-fired crude still: a long horizontal cylinder of riveted steel plate hung on lugs over a brick furnace, with a steam line, manholes, a vapour outlet to the condensers and a bottom outlet for residue. Variable: size; the favoured length is about three times the diameter. Bell's Fig. 15 is a 600-barrel still, 12 ft across and 36 ft long, of 1/2 in plate throughout. Source: H. S. Bell, American Petroleum Refining (1923), pp. 83-92. Picture: Fig. 15 of the book.
ผู้เชี่ยวชาญ
Unknown

คำแนะนำ

1

Size the still

Make it about three times as long as it is wide. Batch stills take overhead about 1.5 gallons per hour per square foot of evaporating surface (two-thirds of diameter x length); continuous ones about 2.5. Give the vapour outlet at least 0.17 sq in per gallon of distillate per hour, placed half to two-thirds of the way from the fire end.

เครื่องมือที่ต้องใช้:

ขนาดที่ไม่ทราบขนาดที่ไม่ทราบ
2

Choose and roll the plates

Use fire-box or still-bottom steel 1/2 in thick for the bottom (5/8 in for stills run down to coke; more is not worth it). Up to 10 ft diameter, 3/8 in flange steel does for the sides and top; larger stills, 1/2 in throughout. Up to 30 ft long: bottom of two plates, sides of three, top of narrow barrel plates; longer: three, four and barrel plates 5 to 6 ft wide. Keep the caulking edges of the bottom plates away from the fire. Dish the heads to a radius equal to the diameter, in one piece up to 10 ft, otherwise seamed on the horizontal diameter, as thick as the shell or 1/16 in thicker.

วัสดุสำหรับขั้นตอนนี้:

แผ่นเหล็กกล้าละมุนแผ่นเหล็กกล้าละมุน1 shell, heads

เครื่องมือที่ต้องใช้:

เครื่องม้วนแผ่นเหล็กเครื่องม้วนแผ่นเหล็ก
เครื่องปั๊มเจาะเครื่องปั๊มเจาะ
3

Rivet and caulk

Double-rivet all seams except at flanges and openings, with 3/4 in rivets even in the bottom, so holes can later be reamed to 7/8 or 1 in for repairs. Bevel and caulk the plates inside and out.

วัสดุสำหรับขั้นตอนนี้:

หมุดย้ำเหล็กกล้าหมุดย้ำเหล็กกล้า1 3/4 in

เครื่องมือที่ต้องใช้:

ค้อนย้ำหมุดค้อนย้ำหมุด
4

Fit openings and steam line

Fit (Fig. 15) a 24 in manhole in the front head, 18 in manholes on top, a 12 in vapour outlet, a 2 in steam line, a tar plug and a 4 in bottom outlet; caulk steel details to the shell and give cast-iron ones a caulking pad. Rivet lugs on the sides.

วัสดุสำหรับขั้นตอนนี้:

ชิ้นงานเหล็กหล่อชิ้นงานเหล็กหล่อ1 manhole frames, outlet castings
ท่อเหล็ก (ผนังหนา ปลายเกลียว)ท่อเหล็ก (ผนังหนา ปลายเกลียว)1 2 in steam line
วาล์วไอน้ำวาล์วไอน้ำ1 ชิ้น
วาล์วประตูน้ำวาล์วประตูน้ำ1 4 in outlet
เหล็กฉากเหล็กกล้าละมุนเหล็กฉากเหล็กกล้าละมุน1 lugs

เครื่องมือที่ต้องใช้:

ค้อนย้ำหมุดค้อนย้ำหมุด
5

Set it over the furnace

Hang the still on lugs from columns on concrete piers, lugs no more than 7 ft apart, so it is independent of the brickwork (Fig. 21). Set it at least 7 to 8 ft above the grates or burners, or better, put the fire box in a Dutch oven in front, for clean combustion. Batch stills expose about a third of the circumference to the fire; for continuous running raise the lugs 12 in above the centre line with a stiff tie between them and fire the full half circumference.

วัสดุสำหรับขั้นตอนนี้:

คอนกรีตคอนกรีต1 piers
อิฐดินทนไฟอิฐดินทนไฟ1 furnace lining
อิฐอิฐ1 setting

เครื่องมือที่ต้องใช้:

เกรียงก่อเกรียงก่อ

วัสดุ

10

เครื่องมือที่จำเป็น

5

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...