İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Rocking-Churns Water-Jacket Churn: Two Small Churns Rock and Their Dashers Plunge, Wings Turn Above
Buttercup

Oluşturan

Buttercup

11. Kasım 2026IE
15
0
0
0
0

Rocking-Churns Water-Jacket Churn: Two Small Churns Rock and Their Dashers Plunge, Wings Turn Above

Samuel Gissinger of Allegheny, Pennsylvania, received US 25,502, dated 20 September 1859, for a churn. Inside a case with a water space under its bottom and sides, a lift-out frame holds two shafts. The upper one turns with wings on it and two cranks; from each crank a stem works a dasher inside a small churn hung on the lower shaft, so the dashers plunge while the churns and the wings between them rock. Warm or cold water in the jacket sets the cream's temperature. The patent gives no sizes; every size here is ours. Its drawing shows the two dashers at different heights; with both churns fixed on one shaft that would bind, so here the cranks are in step.
İleri
About 3 days, plus printing

Talimatlar

1

How a stem rocks its churn

Jupyter defteri yükleniyor…
2

A churn with a water chamber, a few weeks before

Langdon's box turned round a fixed dash-frame. Gissinger's case stands still with water under and beside it, and the dashers work inside two small churns that rock.
3

Read US 25,502

"Having all things arranged as represented in Fig. 1 of the drawings, the milk or cream is put in the case (a), and warm or cold water as the case may require is put in the chamber (o) at pipe (r) the exit opening being closed with a suitable stopple. And now by turning crank (q) which will revolve the shaft (f) with its wings (g), and also operate the dashers (m) and give to the churns (i) and their wings (h) an oscillating motion"
4

Print the churns i

A churn 120 mm across and 108 mm deep with a lug under its floor bored 12.6 mm for shaft j and a cross hole for a pin. Print two. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Tasarım DosyasıSTLCC0 - Free
5

Print the dashers m

A disc 108 mm across and 8 mm thick with six 14 mm holes and a boss bored 8.4 mm for the stem. Print two. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Tasarım DosyasıSTLCC0 - Free
6

Print the wings g

A paddle 60 x 96 x 6 mm with three 20 mm holes on a split hub that clamps round the 12 mm shaft with two M4 screws. Print two. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Tasarım DosyasıSTLCC0 - Free
7

Case a, chamber o, lid b

From 20 mm hardwood make the inner case n 460 x 260 mm and 380 mm deep inside. Build the outer case round it with a 30 mm space under the bottom and along both long sides, sharing the two ends; set a spacer strip under the middle. Close the tops of the side spaces with strips, fit a short brass tube in one as the supply pipe r, and bore a hole low in the other side for a rubber stopper as the exit p. In one end cut a slot 26 mm wide from the top down to 217 mm for the crank shaft. Glue two strips 18 x 20 mm up the inside of each end, 124 mm apart, as the guides. Make the lid in two halves with a handle c on each. Fill the case and the chamber with water overnight so they swell tight, then empty them.

Bu adım için malzemeler:

Sert Ağaç TahtasıSert Ağaç Tahtası5 adet
Ahşap TutkalıAhşap Tutkalı1 adet
Ahşap vidalarAhşap vidalar40 adet
Pirinç boruPirinç boru1 adet
Kauçuk tıpalarKauçuk tıpalar1 adet
Sert ağaç kavelalarSert ağaç kavelalar1 adet

Gerekli aletler:

Daire testere tezgâhıDaire testere tezgâhı
El TesteresiEl Testeresi
Kablosuz MatkapKablosuz Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Yassı matkap ucu takımıYassı matkap ucu takımı
Zıvana yuvası kalemiZıvana yuvası kalemi
Ahşap TokmakAhşap Tokmak
Çubuklu işkenceÇubuklu işkence
Marangoz gönyesiMarangoz gönyesi
Şerit MetreŞerit Metre
SuSu
8

Frame e and the two shafts

Cut two end plates 122 x 20 mm, 375 mm long, to stand between the guides, and bore each 12.8 mm at 230 mm and 40 mm up. Bend 12 mm stainless rod into the shaft f: two cranks of 40 mm throw, 280 mm apart and pointing the same way, each pin 30 mm long, heating each bend red with the torch; leave one end long enough to pass through the slot and bend it into the crank q, 130 mm long, with a hardwood handle. Cut shaft j from the same rod, 456 mm long.

Bu adım için malzemeler:

Sert Ağaç TahtasıSert Ağaç Tahtası1 adet
Paslanmaz çelik çubukPaslanmaz çelik çubuk2 adet
Sert ağaç kavelalarSert ağaç kavelalar1 adet
Ahşap TutkalıAhşap Tutkalı1 adet

Gerekli aletler:

Daire testere tezgâhıDaire testere tezgâhı
Kablosuz MatkapKablosuz Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Propan PürmüzPropan Pürmüz
Tezgah MengenesiTezgah Mengenesi
ÇekiçÇekiç
Isıya Dayanıklı EldivenIsıya Dayanıklı Eldiven
Demir TesteresiDemir Testeresi
Eğeler (El Eğesi)Eğeler (El Eğesi)
9

Churns, dashers, stems and wings

Pin the two churns on shaft j under the cranks, mouths up, and pin a hardwood wing h, 150 x 95 x 20 mm, on j between them. Cut two stems from 8 mm stainless rod, fix each in a dasher's boss, and bend its top into an eye round its crank pin so the pin sits 110 mm above the dasher, closing it with the torch and pliers. Clamp the two wings g on the shaft f between the cranks, pointing opposite ways. Put shafts f and j through the end plates and the dashers into the churns.

Bu adım için malzemeler:

Paslanmaz çelik çubukPaslanmaz çelik çubuk1 adet
Sert Ağaç TahtasıSert Ağaç Tahtası1 adet
Makine vidalarıMakine vidaları4 adet
Naylon Fiberli Emniyet SomunuNaylon Fiberli Emniyet Somunu4 adet
KopilyaKopilya6 adet
PETG filamentPETG filament1 adet

Gerekli aletler:

FDM 3B yazıcıFDM 3B yazıcı
Propan PürmüzPropan Pürmüz
Tezgah MengenesiTezgah Mengenesi
Isıya Dayanıklı EldivenIsıya Dayanıklı Eldiven
Demir TesteresiDemir Testeresi
Kablosuz MatkapKablosuz Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Tornavida takımıTornavida takımı
Zımpara KağıdıZımpara Kağıdı
10

The build in 3D

FreeCAD model of this build, the case cut through its middle: the water space under and beside the inner case, the frame's end plates in their guides, the bent shaft f with its two cranks in step and its wings, the churns on shaft j with the wing between them, and the dashers on their stems. The crank was turned through 24 positions.
Tasarım DosyasıBLENDCC0 - Free
11

Churn

Stopper the exit and pour warm or cold water into the chamber through the pipe until the cream will sit at about 15 °C. Lower the frame into its guides, pour in about 22 litres of heavy cream, checking it with the thermometer, and put the lid on. Turn the crank steadily, timing it. When the butter comes, lift the frame out, gather the butter, drain the buttermilk and the chamber, wash the butter in cold water until it runs clear, salt and weigh it.

Bu adım için malzemeler:

Yağlı kremaYağlı krema22 l
İri Deniz Tuzuİri Deniz Tuzu1 adet
SuSu1 adet

Gerekli aletler:

Takılı kalan problu termometreTakılı kalan problu termometre
KronometreKronometre
Dijital Mutfak TerazisiDijital Mutfak Terazisi
Büyük paslanmaz çelik karıştırma kâsesiBüyük paslanmaz çelik karıştırma kâsesi
12

Troubleshooting

Rocking-churns churn troubleshooting.

Flow

Loading...
13

History and honest limits

**Samuel Gissinger** of Allegheny, Pennsylvania, US 25,502, 20 September 1859, "Churn". He claimed the arrangement in the movable frame e of the oscillating churns i with dashers m and wings h, in combination with the revolving shaft f and its wings g. The patent gives no sizes; every size here is ours. His Fig. 1 draws the two dashers at different heights, but both churns are "secured to the shaft (j)": cranks out of step would push them opposite ways and bind, so ours are in step. His case is rounded at the ends and the water chamber tapered; ours is square.

Malzemeler

14

Gerekli Aletler

24

Tasarım dosyaları

4
  • gissinger-rocking-churns-water-jacket-churn-churn.stlSTLCC0
  • gissinger-rocking-churns-water-jacket-churn-dasher.stlSTLCC0
  • gissinger-rocking-churns-water-jacket-churn-wing-g.stlSTLCC0
  • gissinger-rocking-churns-water-jacket-churn.blendBLENDCC0

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...