İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Adjustable-Knife Countersink: Three Knives Set Out Evenly by a Collar and Stopped by a Depth Pin (Logan, 1921)
Forge

Oluşturan

Forge

13. Kasım 2026NO
11
0
0
0
0

Adjustable-Knife Countersink: Three Knives Set Out Evenly by a Collar and Stopped by a Depth Pin (Logan, 1921)

Marselius J. Logan of Springfield, Virginia, received US 1,377,495, dated 10 May 1921. Three knives sit in grooves along a conical head, their bevelled edges just proud of the cone. A collar screwed along the shank pushes all their back ends at once, so each cuts the same share. When they wear, a turn of the collar sets them out again. Set screws lock them. A stop pin beside them halts every countersink at the same depth. The patent gives no sizes; every size here is ours.
İleri
About 2 days

Talimatlar

1

Setting the knives out evenly

Jupyter defteri yükleniyor…
2

Read US 1,377,495

"All of the cutters or knives 10 are made alike in length as well as other dimensions, so that by screwing the collar 7 into contact with the inner ends 12 of all of said cutters, the latter may be evenly adjusted to cut equally, and when their cutting edges 11 become worn down said cutters may be uniformly projected in order to provide the proper clearance."
3

Turn the inner member 1 and the sleeve 4

From 30 mm steel bar turn the inner member: a 90 degree cone 3 26 mm across at its base, a short cylindrical edge under it, and a shank 2 14 mm across, threaded M14 for 20 mm below the head 6 and plain below. From 40 mm bar turn the sleeve: a ring bored 0.03 mm under the head's edge, with a flange 5 30 mm long bored 22 mm, so it leaves an annular space 13 round the shank. Heat the sleeve to 250 C in the oven and drop it over the head's edge; let it cool.

Bu adım için malzemeler:

Yumuşak çelik yuvarlak çubukYumuşak çelik yuvarlak çubuk2 adet
Kesme yağıKesme yağı1 adet

Gerekli aletler:

Metal Torna TezgâhıMetal Torna Tezgâhı
3 ayaklı torna aynası3 ayaklı torna aynası
Torna kesici kalemiTorna kesici kalemi
Delik işleme kateriDelik işleme kateri
Kesme kalemiKesme kalemi
Kılavuz ve pafta takımıKılavuz ve pafta takımı
FırınFırın
Kaynak eldivenleriKaynak eldivenleri
Dijital Kumpas 6 İnçDijital Kumpas 6 İnç
Koruyucu gözlükKoruyucu gözlük
4

Grooves, knives and screws

Saw and file three grooves 4 mm square, parallel to the axis, a third of the way round from each other, through the joint of head and sleeve and on into the annular space. File the cone away 14 ahead of each groove for the shavings. Cut three knives 32 mm long from 4 mm square tool steel, exactly alike, and grind each one's top end to the cone's slope with a bevelled cutting edge 11. Harden them (cherry red, water, temper to light straw). Drill and tap M4 through the sleeve over each groove for the set screws 15. Make a collar 7 with an M14 thread to screw up the shank inside the flange, and an M4 set screw 19 to lock it. Drill and tap M5 into the head's edge behind one knife for the stop pin 16, with an M4 set screw 18 to lock it.

Bu adım için malzemeler:

Kare takım çeliği çubukKare takım çeliği çubuk1 adet
Yumuşak çelik yuvarlak çubukYumuşak çelik yuvarlak çubuk1 adet
Çukur uçlu setuskurÇukur uçlu setuskur5 adet
İçten Altıgen Başlı Silindirik Vidaİçten Altıgen Başlı Silindirik Vida1 adet
Altıgen SomunAltıgen Somun1 adet

Gerekli aletler:

Demir TesteresiDemir Testeresi
Eğe TakımıEğe Takımı
Tezgah MengenesiTezgah Mengenesi
Taşlama motoruTaşlama motoru
Demirci OcağıDemirci Ocağı
Demirci MaşasıDemirci Maşası
Küçük MıknatısKüçük Mıknatıs
Su verme kovasıSu verme kovası
SuSu
Bileği TaşıBileği Taşı
Sütunlu MatkapSütunlu Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Kılavuz ve pafta takımıKılavuz ve pafta takımı
Kılavuz koluKılavuz kolu
Metal Torna TezgâhıMetal Torna Tezgâhı
Dijital Kumpas 6 İnçDijital Kumpas 6 İnç
5

Set, lock and countersink

Slide the knives into their grooves, back ends down in the annular space. Screw the collar up until all three knives' edges stand 0.3 mm out of the cone, and lock it and the knives. Set the stop pin so it touches the work when the countersink is the size wanted, and lock it. Countersink a row of screw holes in hardwood: every one should come out the same.

Gerekli aletler:

Alyan takımıAlyan takımı
Dijital Kumpas 6 İnçDijital Kumpas 6 İnç
Kablosuz MatkapKablosuz Matkap
Matkap Ucu TakımıMatkap Ucu Takımı
Sert Ağaç TahtasıSert Ağaç Tahtası
Koruyucu gözlükKoruyucu gözlük
6

Troubleshooting

Adjustable-knife countersink troubleshooting.

Flow

Loading...
7

History and honest limits

**Marselius J. Logan** of Springfield, Virginia, assignor of one-half to Laurence G. Alexander of Alexandria, Virginia, US 1,377,495, dated 10 May 1921, filed 14 February 1920. He claimed "a flange carried by the head and extending concentrically along the shank in spaced relation thereto, cutters mounted on the head and extending into the space between the same and the flange, and a collar adjustable on the shank within said flange for alining the cutters", and "an adjustable stop". He shows three knives; ours too. He gives no sizes; every size here is ours.

Malzemeler

6

Gerekli Aletler

26

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...