İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER
Screw-Piston Box Churn: The Case Turns and a Piston Runs End to End Along a Five-Start Screw
Buttercup

Oluşturan

Buttercup

10. Kasım 2026IE
8
0
0
0
0

Screw-Piston Box Churn: The Case Turns and a Piston Runs End to End Along a Five-Start Screw

E. L. Pratt of Philadelphia received US 25,306, dated 30 August 1859, for a square box churn with a piston inside. A screw of four or five threads runs the length of the case; the piston rides on it. With the screw held still, turning the case drives the piston from one end to the other, forcing the cream through small grooves across its edges and through holes that a turning disk opens or closes. To finish, the case is held and the screw turned, so the piston presses the butter into each end. Pratt gives no sizes; every size here is ours.
İleri
About 3 days, plus printing

Talimatlar

1

Cream through the grooves

Jupyter defteri yükleniyor…
2

Cream forced through small openings, two weeks before

Lehaye pumped the cream through slots he could narrow. Pratt drives a piston along a screw and narrows its holes with a disk.
3

Read US 25,306

"The operator now takes hold of the crank handle (h) and gives rotary motion to the case (A), thus causing the diaphragm or piston (C) to be forced, by the screw shaft (D), toward, and eventually against, one of the ends (e or e') of the said case (A), when he then gives an opposite rotary motion to the said case (A), and thus forces the said diaphragm (C) to the other end of the same".
4

Print the screw sections

One 100 mm section of the five-start screw, 50 mm across with a 50 mm lead, bored 12.4 mm for the rod. Print four, standing up. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Tasarım DosyasıSTLCC0 - Free
5

Print the piston's outer plate m

A 196 mm square plate 10 mm thick with the five-start nut, eight 16 mm holes o and grooves p across its edges. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Tasarım DosyasıSTLCC0 - Free
6

Print the piston's other outer plate m

The same plate with an arc slot for the disk's peg. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Tasarım DosyasıSTLCC0 - Free
7

Print the piston's middle plate m'

The middle plate with a 140.6 mm hole for the turning disk. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Tasarım DosyasıSTLCC0 - Free
8

Print the disk n

The 140 mm disk with eight holes set between the plates' holes and a peg that comes out through the slot. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Tasarım DosyasıSTLCC0 - Free
9

Case A: sides d, ends e and e', bolts f

From 20 mm hardwood cut four sides 412 mm long, two 200 mm and two 240 mm wide, and two end pieces 280 x 280 x 40 mm. Rout a groove 6 mm deep and 20.5 mm wide in each end's inner face to take the sides' edges as a square 200 mm inside. Cut a 180 x 120 mm opening in one 200 mm side for the lid. Bore the ends 11 mm at the four corners, 128 mm from the middle each way, and draw the case together with four M10 rods, washers and nuts. Bore a blind 20.6 mm hole 30 mm deep in the middle of one end for journal i, and a 20.6 mm hole through the other for journal k. Soak the case in water overnight so it swells tight.

Bu adım için malzemeler:

Sert Ağaç TahtasıSert Ağaç Tahtası3 adet
Dişli milDişli mil4 adet
Altıgen SomunAltıgen Somun8 adet
Düz PulDüz Pul8 adet

Gerekli aletler:

Daire testere tezgâhıDaire testere tezgâhı
El TesteresiEl Testeresi
Marangoz keskileriMarangoz keskileri
Kablosuz MatkapKablosuz Matkap
Yassı matkap ucu takımıYassı matkap ucu takımı
Matkap Ucu TakımıMatkap Ucu Takımı
Çubuklu işkenceÇubuklu işkence
Marangoz gönyesiMarangoz gönyesi
Kurbağacık anahtarKurbağacık anahtar
SuSu
10

Screw shaft D and its journals

Thread the four screw sections on a 580 mm M12 stainless rod so their threads run on from one to the next, with a 20 mm stainless tube on each side as journals i and k. Clamp the stack with nuts and washers so the screw turns with the rod. Thread the piston on before the last section goes on. Put journal i in the blind hole, pass journal k through the other end, and draw the case up round them.

Bu adım için malzemeler:

Dişli milDişli mil1 adet
Paslanmaz çelik boruPaslanmaz çelik boru1 adet
Altıgen SomunAltıgen Somun4 adet
Düz PulDüz Pul4 adet
PETG filamentPETG filament1 adet

Gerekli aletler:

FDM 3B yazıcıFDM 3B yazıcı
Demir TesteresiDemir Testeresi
Eğeler (El Eğesi)Eğeler (El Eğesi)
Kurbağacık anahtarKurbağacık anahtar
11

Piston C

Glue the middle plate to the plain outer plate, drop the disk into its hole, peg up, and glue the slotted plate on top so the peg comes out through the slot and the disk turns freely. Line up the nuts' threads before the glue sets by running the piston onto a screw section.

Bu adım için malzemeler:

Ahşap TutkalıAhşap Tutkalı1 adet

Gerekli aletler:

Çubuklu işkenceÇubuklu işkence
12

Lid q, frame B, cranks and pin v

Make the lid from hardwood to fit the opening, with a 6 mm lip all round, and two hardwood buttons r screwed to the case to turn over it. Fix a hardwood block on the outside of end e and pin a 20 mm steel stub in it as journal g, with a crank h. Fix a crank l on the rod's end outside journal k. Build a frame of two uprights on a base, 580 mm apart, with open slots for the journals. Bore 10 mm holes through each upright and its end piece, and through the crank l, for the pin v.

Bu adım için malzemeler:

Sert Ağaç TahtasıSert Ağaç Tahtası1 adet
Yumuşak ağaç 70x70 mmYumuşak ağaç 70x70 mm2 adet
Ham çelik çubukHam çelik çubuk2 adet
Sert ağaç kavelalarSert ağaç kavelalar1 adet
Ahşap vidalarAhşap vidalar16 adet
Ahşap TutkalıAhşap Tutkalı1 adet

Gerekli aletler:

El TesteresiEl Testeresi
Dekupaj TestereDekupaj Testere
Kablosuz MatkapKablosuz Matkap
Yassı matkap ucu takımıYassı matkap ucu takımı
Matkap Ucu TakımıMatkap Ucu Takımı
Demir TesteresiDemir Testeresi
Şerit MetreŞerit Metre
13

The build in 3D

FreeCAD model of this build, the case cut open: the sides let into the ends and held by the four corner bolts, the lid and its buttons, the five-start screw on its journals, the piston in the middle with its grooves and holes, the two cranks and the frame. The case was turned through 16 angles.
Tasarım DosyasıBLENDCC0 - Free
14

Churn, then press

Turn the disk's peg to open or close the holes for the cream's thickness. Pour about 6 litres of heavy cream at about 15 °C, checked with the thermometer, through the lid opening, button the lid down and pin crank l to its upright. Turn crank h one way about seven and a half turns until the piston stops at one end, then back the other way, timing it. When the butter comes, pin the case instead and turn crank l to drive the piston against each end and press the butter there. Open the lid, lift the butter out, drain the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.

Bu adım için malzemeler:

Yağlı kremaYağlı krema6 l
İri Deniz Tuzuİri Deniz Tuzu1 adet
SuSu1 adet

Gerekli aletler:

Takılı kalan problu termometreTakılı kalan problu termometre
KronometreKronometre
Dijital Mutfak TerazisiDijital Mutfak Terazisi
Büyük paslanmaz çelik karıştırma kâsesiBüyük paslanmaz çelik karıştırma kâsesi
15

Troubleshooting

Screw-piston churn troubleshooting.

Flow

Loading...
16

History and honest limits

**E. L. Pratt** of Philadelphia, assignor to himself and R. B. Fitts, US 25,306, 30 August 1859, "Churn". He claimed the rotary case with a piston that both moves along and turns on a screw, with grooves across its edges, and the piston of three pieces with a disk to open, adjust or close its holes. He gives no sizes, so every size here is ours; he made the piston of wood, and ours is printed, with a peg through a slot to turn the disk.

Malzemeler

14

Gerekli Aletler

19

Tasarım dosyaları

6

CC0 Kamu Malı

Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.

Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

Tartışma

(0)

Giriş yapın tartışmaya katılmak için

Yorumlar yükleniyor...