İşbirliği
SANAT
GÜZELLİK & SAĞLIK
ZANAAT
KÜLTÜR & TARİH
EĞLENCE
ÇEVRE
YİYECEK & İÇECEK
TERS MÜHENDİSLİK
BİLİMLER
SPOR
TEKNOLOJİ
GİYİLEBİLİR ÜRÜNLER

Segment-Rack Zone Churn: A Lever Rocks the Dasher Shaft, a Toothed Tin Band Gathers the Butter at the Surface
Charles W. Stafford of Burlington, Iowa, received US 22,093, dated 16 November 1858, for a churn worked by a lever: a toothed segment on a pivot turns a pinion on the upright dasher shaft back and forth. Four level arms and three slanted floats beat the cream. A tin band with ten tabs on its inside rides on slides at the arms' ends and is set with its top edge at the cream's surface, where the tabs gather the butter as it forms. The cover twists onto two ears on the rim and has a small hatch.
This rung builds it in a 20-litre bucket with printed gears.
İleri
About 8 hours, plus printing
Talimatlar
1
1
Swing, fill and the zone's height
Swing, fill and the zone's height
Jupyter defteri yükleniyor…
2
2
A toothed segment working a dasher, before it
A toothed segment working a dasher, before it
That segment drove a dasher up and down. Stafford's turns the dasher shaft back and forth.
3
3
Read US 22,093
Read US 22,093
"This zone is intended to be raised or lowered along the slide so as to accommodate itself to the quantity of cream in the churn—the upper edge being intended to rise to the surface of the cream or a little higher so that the radial proportions may gather the butter as it is formed."
4
4
Print the segment S
Print the segment S
The toothed segment with its socket H for the lever. Print it flat, teeth up. PETG, 0.2 mm layers, 40 % infill, 4 walls; wash before first use.
5
5
Print the pinion N
Print the pinion N
The 12-tooth pinion for the shaft's top. PETG, 0.2 mm layers, 40 % infill, 4 walls; wash before first use.
6
6
Print the ear E
Print the ear E
An ear hook for the bucket's rim. Print two. PETG, 0.2 mm layers, 40 % infill, 4 walls; wash before first use.
7
7
Print the socket W
Print the socket W
The foot socket the shaft stands in. PETG, 0.2 mm layers, 40 % infill, 4 walls; wash before first use.
8
8
Print the zone clip
Print the zone clip
A clip that holds the zone on a slide. Print two. PETG, 0.2 mm layers, 40 % infill, 4 walls; wash before first use.
9
9
Cover B, ears and hatch D
Cover B, ears and hatch D
Cut an 18 mm plywood disc 350 mm across for cover B, with a 17 mm hole in the middle and a 110 mm hole 106 mm off centre. Glue two 12 mm plywood rings under it, 292/264 mm and 350/312 mm across: the gap between them is the groove that takes the bucket's rim. Screw the two ears to the bucket's wall on opposite sides, hooks over the rim, and cut two 44 mm notches in the cover's edge and outer ring to pass them: drop the cover on and turn it 45 degrees to lock. Cut a 130 mm hatch D from 6 mm plywood with a dowel knob.
Bu adım için malzemeler:
Kontrplak levha2 adet
Ahşap Tutkalı1 adet
Ahşap vidalar8 adet
Sert ağaç kavelalar1 adet
PETG filament1 adetGerekli aletler:
FDM 3B yazıcı
Dekupaj Testere
Panç testere seti
Kablosuz Matkap
Matkap Ucu Takımı
İşkenceler
Zımpara Kağıdı
Tornavida takımı10
10
Shaft, arms, floats and zone
Shaft, arms, floats and zone
Screw the socket to the middle of the bucket's floor with an M4 screw and lock nut. Cut the stainless tube (16 mm) to 433 mm. Cut four hardwood arms 248 x 30 x 10 mm and three floats 216 x 40 x 8 mm; bore each 16.5 mm at its middle and the arms 8.4 mm at 118 mm each side. Fix the arms on the shaft 115, 140, 165 and 190 mm above its foot, all in line, and the floats 35, 60 and 85 mm up, each an eighth of a turn round more than the last and slanted 25 degrees, with M4 screws across. Push an 8 mm stainless rod 200 mm long through each end of the arms as the slides. Cut a tinplate strip 60 x 810 mm, roll it into a 253 mm band and screw the lap with M3 screws; screw ten tinplate tabs 26 x 50 mm inside it, evenly spaced. Clip it to the slides at the height the notebook gives.
Bu adım için malzemeler:
Paslanmaz çelik boru1 adet
Sert Ağaç Tahtası1 adet
Paslanmaz çelik çubuk1 adet
Teneke sac1 adet
Makine vidaları22 adet
Naylon Fiberli Emniyet Somunu22 adetGerekli aletler:
Boru kesici
Demir Testeresi
El Testeresi
Kablosuz Matkap
Matkap Ucu Takımı
Sac makası
Eğeler (El Eğesi)
Tornavida takımı
Kurbağacık anahtar
Şerit Metre11
11
Gears, upright and lever
Gears, upright and lever
Stand the shaft in its socket, lay the cover on and lock it. Fix the pinion on the shaft's top with an M4 screw across. Screw a hardwood upright I 44 x 30 mm, 162 mm tall, to the cover from below, its front face 38 mm behind the shaft's centre. Bolt the segment to it with an M12 bolt as pivot M so its teeth mesh with the pinion, and screw a hardwood lever G 340 x 30 x 14 mm on top of its socket.
Bu adım için malzemeler:
Sert Ağaç Tahtası1 adet
Ahşap vidalar4 adet
Makine vidaları1 adet
Naylon Fiberli Emniyet Somunu1 adet
Altıköşe cıvata takımı1 adet
Düz Pul2 adetGerekli aletler:
El Testeresi
Kablosuz Matkap
Matkap Ucu Takımı
Kurbağacık anahtar
Tornavida takımı12
12
The build in 3D
The build in 3D
FreeCAD model of this build, the near quarter of the bucket, cover and zone cut away: the shaft with four arms, three slanted floats, the slides and the toothed zone, the cover with its rings, ears and hatch, the upright, the segment and pinion, and the lever.
13
13
Churn
Churn
Stand the bucket in a tub of ice water in warm weather or warm water in cold weather (ours, for his receptacle at the side) until the cream is about 15 °C. Pour in about 12 litres of heavy cream and set the zone's top edge at its surface. Lock the cover and rock the lever back and forth steadily; time it. Look through the hatch: the tabs gather the butter at the surface. When it has come, lift the cover and shaft out, pour off the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.
Bu adım için malzemeler:
Yağlı krema12 l
Kırılmış buz2 kg
İri Deniz Tuzu1 adet
Su1 adetGerekli aletler:
Gıda sınıfı saklama kabı
Takılı kalan problu termometre
Kronometre
Dijital Mutfak Terazisi
Büyük paslanmaz çelik karıştırma kâsesi14
14
Troubleshooting
Troubleshooting
Segment-rack churn troubleshooting.
Flow
Loading...
15
15
History and honest limits
History and honest limits
**Charles W. Stafford** of Burlington, Iowa, US 22,093, 16 November 1858, "Churn". He preferred a tin body, light, cheap and quick to warm or cool, and claimed the general arrangement, the adjustable zone with its projections, the grooved cover with slots and ears, and the two covers. He gave no sizes. Every size and material is ours. His Fig. 4 draws S toothed on its face and N bevelled; ours is a crown-toothed segment with a straight pinion. His water receptacle hangs on the body's side; ours is a tub the bucket stands in.
Malzemeler
17- 2 adetYer Tutucu
- 1 adetYer Tutucu
- 12 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
- 23 adetYer Tutucu
- Yer Tutucu
- 1 adetYer Tutucu
- 2 adetYer Tutucu
- 12 lYer Tutucu
- 2 kgYer Tutucu
- 1 adetYer Tutucu
- 1 adetYer Tutucu
Gerekli Aletler
20- Yer Tutucu
- 1 vendor sell this, none ship to you yetYer Tutucu
- Yer Tutucu
- 1 vendor sell this, none ship to you yetYer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- 1 vendor sell this, none ship to you yetYer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
- Yer Tutucu
Tasarım dosyaları
6Bu planla yapılan
İlgili Blueprint'ler
Bu blueprint'ler bilgi paylaşır — teknikler, malzemeler veya ilkeler

Rack-and-Segment Crank Churn: A Crank Rocks a Toothed Segment That Drives the Dasher Up and Down
Buttercup tarafından
YİYECEK & İÇECEK
43
0
0
0
0
0

Spiral-Beater Box Churn: Diamond-Holed and Hollow-Ended Beaters Drive the Cream End to End
Buttercup tarafından
Ağaç işleri
9
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
TheChef tarafından
ZANAAT
63
0
0
0
0
0
CC0 Kamu Malı
Bu plan CC0 lisansıyla yayınlanmıştır. İzin almadan kopyalayabilir, değiştirebilir, dağıtabilir ve herhangi bir amaçla kullanabilirsiniz.
Planı üzerinden ürün satın alarak Maker'ı destekleyin, böylece Maker Komisyonu Satıcılar tarafından belirlenen komisyonu kazanırlar veya bu Planın yeni bir versiyonunu oluşturun ve gelir paylaşımı için kendi Planınıza bağlantı olarak ekleyin.

