Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Canteen From Two Pie Plates: Rims Soldered Together, a Screw-Cap Neck in the Edge (Boy Mechanic, 1919)
Tinny

Створено

Tinny

13. листопад 2026US
7
0
0
0
0

Canteen From Two Pie Plates: Rims Soldered Together, a Screw-Cap Neck in the Edge (Boy Mechanic, 1919)

A canteen "for the camper or hiker", sent to The Boy Mechanic (1919) by J. R. Townsend of Itasca, Texas: two nickel-plated pie plates soldered rim to rim, the screw-capped neck of a metal-polish can soldered over an opening in the edge, and two wire loops for the snap hooks of a shoulder strap. The book gives no sizes: the plates set the size.
Початківець
About 2 hours

Інструкції

1

Read The Boy Mechanic

"Two good-quality pie plates were soldered at their edges to form a water-tight container." (J. R. Townsend, Itasca, Texas.)
2

Solder the plates together

Take two good-quality nickel-plated pie plates of the same size. Clean the rims, set them face to face, and solder them together all round the edge so the joint is water-tight. Use lead-free solder: this holds drinking water (our choice; the book only says solder).

Матеріали для цього кроку:

Форма для пирогаФорма для пирога2 штук
Безсвинцевий водопровідний припійБезсвинцевий водопровідний припій1 штука
ФлюсФлюс1 штука

Необхідні інструменти ({count})

Електричний паяльникЕлектричний паяльник
Напилок по металуНапилок по металу
3

Cut the neck off the can

Take a small metal-polish can with a screw cap. As the book's drawing shows, cut off its sloping top with the threaded neck, and trim the cut edge.

Матеріали для цього кроку:

БляшанкаБляшанка1 штука

Необхідні інструменти ({count})

Ножиці по металу посиленіНожиці по металу посилені
Напилок по металуНапилок по металу
4

Cut the opening and fit the neck

Cut an opening in the edge of the canteen to suit the neck. Fit the neck carefully over it and solder it all round.

Матеріали для цього кроку:

Безсвинцевий водопровідний припійБезсвинцевий водопровідний припій1 штука
ФлюсФлюс1 штука

Необхідні інструменти ({count})

Ручний дрильРучний дриль
Напилок по металуНапилок по металу
Електричний паяльникЕлектричний паяльник
5

Solder on the strap loops

Bend two short pieces of wire into loops and solder one at each side of the screw cap, as loops for the snap hooks of the shoulder strap.

Матеріали для цього кроку:

Залізний дрітЗалізний дріт1 штука
Безсвинцевий водопровідний припійБезсвинцевий водопровідний припій1 штука
ФлюсФлюс1 штука

Необхідні інструменти ({count})

ПлоскогубціПлоскогубці
Електричний паяльникЕлектричний паяльник
6

Fit the strap and test

Put a snap hook on each end of a shoulder strap and hook them into the loops. Fill the canteen with water, screw on the cap and check every joint for leaks (our test), then rinse it before use.

Матеріали для цього кроку:

Шкіряний ремінецьШкіряний ремінець1 штука
КарабінКарабін2 штук

Необхідні інструменти ({count})

Прісна водаПрісна вода
7

Troubleshooting

Canteen troubleshooting.

Flow

Loading...
8

History and honest limits

From **The Boy Mechanic, Book 3**, edited by H. H. Windsor, Popular Mechanics, Chicago, 1919 (Project Gutenberg 71856), "How to Make a Canteen", sent in by J. R. Townsend of Itasca, Texas. The book gives no sizes and names no tools; the lead-free solder, the tools, the strap material and the leak test are ours.

Матеріали

7

Необхідні інструменти

6

За цим кресленням виготовляють

Пов'язані креслення

Ці креслення діляться знаннями — техніки, матеріали або принципи

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...