Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО

Digital Kitchen Scale: a Cantilever Load Cell in a Sealed Dual Housing (Edlund, 2009)
A digital scale built to survive a kitchen: spills, washing and being dropped. The load cell is a short cantilever with a strain sensor on top, and the electronics sit in a sealed compartment. Both are in a plastic chassis held loosely inside a second, outer housing of stainless steel and plastic, with crushable spacers between the two.
Result: a digital kitchen scale with a removable pan, sealed display and touchpad, battery power and an overload stop under the load cell.
Source: R. S. Whitney (Edlund Company), US Patent 7,554,043 (2009). Unknown: sizes, capacity, resolution and the electronics; the patent says suitable force transducers are readily available. Ours: the display and button types. Picture: Wikimedia Commons.
Просунутий
2 days
Інструкції
1
1
Mount the cantilever load cell
Mount the cantilever load cell
In the load-cell cavity of the plastic chassis, screw a base plate to the cavity floor. Screw the cantilever support to the base plate; a support plate on the cantilever carries the posts for the pan. A strain transducer on top of the cantilever senses the top stretching as it bends under a load. A window in the base plate leaves the cavity floor just below the free end, so an overload bottoms out there instead of breaking the transducer.
Матеріали для цього кроку:
Тензодатчик1 cantilever type
Пластмаса1 chassis
Машинні гвинти1 набірНеобхідні інструменти ({count})
Набір викруток
Невідомі розміри2
2
Seal in the electronics
Seal in the electronics
On the other side of the chassis, fit the display electronics behind one opening and the touchpad electronics behind another, wired to the strain transducer through sealing bushings. Fit a battery holder. Close the compartment with its cover on gaskets, so the electronics stay dry. Not given: the circuit, the display and the battery. Ours: a segment LCD and push buttons.
Матеріали для цього кроку:
Інтегральна мікросхема1 weighing and display electronics
Сегментний РК-індикатор1 штука
Кнопка1 touchpad keys
Акумулятор1 штука
Прокладка2 штук
Монтажний провід1 short
Дріт припою1 a littleНеобхідні інструменти ({count})
Паяльник
Набір викруток3
3
Close it in the outer housing
Close it in the outer housing
Place the chassis, unfastened, between the two halves of the outer housing: a stainless-steel top with downturned sides, and a plastic bottom. Spacers moulded on the chassis sides press against the housing sides. They take a blow if the scale is dropped, and may crush on purpose to save the load cell and electronics. A sealed window of plastic or glass shows the display. A flexible sheet covers the touchpad. Fit four height-adjustable feet.
Матеріали для цього кроку:
Лист нержавкої сталі1 upper housing
Пластмаса1 lower housing
Невідомий матеріал1 window, touchpad sheet, four feetНеобхідні інструменти ({count})
Набір викруток
Невідомі розміри4
4
Fit the pan and check
Fit the pan and check
Screw the pan support to the four supports of the load cell. Rest the removable pan on it, or snap it on, so it lifts off for washing. A flexible boot can seal each support where it passes through the housing. Ours: check the reading with calibration weights.
Матеріали для цього кроку:
Шалька терезів1 metal or plastic
Машинні гвинти1 набірНеобхідні інструменти ({count})
Набір викруток
Набір калібрувальних гирМатеріали
13- 1 cantilever typeЗаповнювач
- 1 lower housingЗаповнювач
- 2 наборівЗаповнювач
- 1 weighing and display electronicsЗаповнювач
- 1 штукаЗаповнювач
- Заповнювач
- 1 штукаЗаповнювач
- 2 штукЗаповнювач
- 1 shortЗаповнювач
- 1 a littleЗаповнювач
- 1 upper housingЗаповнювач
- 1 window, touchpad sheet, four feetЗаповнювач
- 1 metal or plasticЗаповнювач
Матеріали з пов'язаних креслень

10% атрибуція
Mechanical Kitchen Scale: Sheet-Metal Case, Guided Plate and Two Springs to a Dial (Hansen, 1939)
від Penny
Механіка
8
0
0
0
1
0

10% атрибуція
Electronic Baby Scale That Holds a Steady Reading: Hino & Itani, 1981
від Penny
електроніка
29
0
0
0
2
0

10% атрибуція
Strain-Gauge Load Cell with Floating Piston: Ruge, 1949
від Penny
електроніка
31
0
0
0
3
0
За цим кресленням виготовляють
Пов'язані креслення
Ці креслення діляться знаннями — техніки, матеріали або принципи
CC0 Суспільне надбання
Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.
Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

