Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Foot-Fed Carriage Saw Table: The Saw Rides on Balls Under the Table, a Foot Lever Pulls It Through the Work (Hall, 1933)
Forge

Створено

Forge

13. листопад 2026NO
7
0
0
0
0

Foot-Fed Carriage Saw Table: The Saw Rides on Balls Under the Table, a Foot Lever Pulls It Through the Work (Hall, 1933)

Harry O. Hall of Murray, Utah, received US 1,930,168, dated 10 October 1933, for a portable saw table where the saw moves and the work stays still. The saw and its motor hang from a carriage under the top. The carriage rolls on balls in V-shaped tracks in a straight line. A foot lever pulls it back through a board held against the fence, and springs bring it forward again. Nuts on a hanging stem set the depth, and a spring under the motor keeps the belts tight. The table rolls on wheels and its back legs fold. The patent gives no sizes; every size here is ours, and our top is plywood where his is folded sheet metal.
Просунутий
About 1 week

Інструкції

1

The foot lever, the travel and the cut

Завантаження блокнота Jupyter…
2

Read US 1,930,168

"The movable saw carriage is mounted to freely move longitudinally of the table in a straight line and is moved into engagement with the piece of work held in position by the work fence, when the lever 29' is depressed by the foot."
3

Table and legs

Make the top 5 of 18 mm plywood 1000 x 600 mm with pine aprons 6, 7 round it, and cut a slot 47 12 mm wide and 500 mm long down its middle. Fix four pine legs 9, 10 splayed outwards at the corners with braces 11 and plywood gussets 12, the top 850 mm high; bolt the rear legs' gussets with one bolt each as a pivot and a second removable bolt, so they fold. Put an axle 15 between the front legs with a wheel 14 on each end.

Матеріали для цього кроку:

Лист фанериЛист фанери1 штука
Сосновий пиломатеріалСосновий пиломатеріал6 штук
Круглий пруток з маловуглецевої сталіКруглий пруток з маловуглецевої сталі1 штука
Набір гумових колісНабір гумових коліс1 штука
Болт із півкруглою головкоюБолт із півкруглою головкою8 штук
Шурупи по деревуШурупи по дереву40 штук
Столярний клейСтолярний клей1 штука

Необхідні інструменти ({count})

ЕлектролобзикЕлектролобзик
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Струбцина з напрямноюСтрубцина з напрямною
Комбінований кутникКомбінований кутник
РулеткаРулетка
4

Tracks and carriage

Screw a pine rail 22 along each side under the top and bolt a length of steel angle on it, V upwards, as the track 21. Make the carriage of two more angles 16, V downwards over the tracks, joined near each end by a cross bolt 17 with nuts 19 either side of each angle, so their spacing can be set. Under each end of each carriage angle, between the bolt and a small steel lug 23 bolted inside the angle, put a 10 mm steel ball 20 to roll in the track. Hook two springs 24 from the front wall of the top to the front cross bolt.

Матеріали для цього кроку:

Сосновий пиломатеріалСосновий пиломатеріал1 штука
Кутник із м'якої сталіКутник із м'якої сталі2 штук
Набір шестигранних болтівНабір шестигранних болтів12 штук
Шпилька різьбоваШпилька різьбова1 штука
Шестигранна гайкаШестигранна гайка8 штук
Смуга з маловуглецевої сталіСмуга з маловуглецевої сталі1 штука
Кулькові підшипникиКулькові підшипники1 штука
Пружина розтягуПружина розтягу2 штук
Шурупи по деревуШурупи по дереву16 штук

Необхідні інструменти ({count})

Ножівка по металуНожівка по металу
Кутова шліфмашинаКутова шліфмашина
Свердлильний верстатСвердлильний верстат
Набір сверделНабір свердел
Набір напилківНабір напилків
Слюсарні лещатаСлюсарні лещата
Розвідний ключРозвідний ключ
Захисні окуляриЗахисні окуляри
5

Foot lever and chain

Pivot a hardwood foot lever 29' on the front axle, reaching back along the floor, with a pedal 31 on its free end. Fix a pulley 28 on a shaft 29 between the rear legs. Run a chain 27 from the rear cross bolt of the carriage over the pulley and down to the lever, fixed 450 mm from its pivot. Pressing the pedal pulls the carriage back; letting go, the springs return it.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини1 штука
БлокБлок1 штука
Круглий пруток з маловуглецевої сталіКруглий пруток з маловуглецевої сталі1 штука
Роликовий ланцюгРоликовий ланцюг1 штука
Набір шестигранних болтівНабір шестигранних болтів3 штук

Необхідні інструменти ({count})

ЕлектролобзикЕлектролобзик
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Ножівка по металуНожівка по металу
Розвідний ключРозвідний ключ
6

Saw frame, arbor and shield

Bolt a rectangle of steel angle as the saw frame 32. Hang one end on the rear cross bolt between two collars 33 with set screws 34, so it can be slid sideways. On the front cross bolt put a sleeve 35 between collars 36 with a threaded stem 38 hanging from it, through a hole 39 in the frame's end, with a clamping nut 40 above and below: these set the saw's height. Bolt two flange bearings 42 across the frame and fit a 30 mm arbor 43 turned with a collar, a loose flange and an M20 thread; put the 250 mm blade on one end, centred under the slot, and a V-belt pulley 49 on the other. Bend a sheet steel shield 48 round the lower half of the blade and bolt it to the frame.

Матеріали для цього кроку:

Кутник із м'якої сталіКутник із м'якої сталі1 штука
Круглий пруток з маловуглецевої сталіКруглий пруток з маловуглецевої сталі2 штук
Установчий гвинт із чашоподібним кінцемУстановчий гвинт із чашоподібним кінцем4 штук
Шпилька різьбоваШпилька різьбова1 штука
Шестигранна гайкаШестигранна гайка4 штук
Фланцевий підшипникФланцевий підшипник2 штук
Circular Saw Blade SetCircular Saw Blade Set1 штука
Шків клинового паса (профіль A)Шків клинового паса (профіль A)1 штука
Лист маловуглецевої сталіЛист маловуглецевої сталі1 штука
Набір шестигранних болтівНабір шестигранних болтів10 штук

Необхідні інструменти ({count})

Ножівка по металуНожівка по металу
Кутова шліфмашинаКутова шліфмашина
Свердлильний верстатСвердлильний верстат
Набір сверделНабір свердел
Набір мітчиків і плашокНабір мітчиків і плашок
Коловорот для мітчиківКоловорот для мітчиків
Токарний верстат по металуТокарний верстат по металу
Трикулачковий токарний патронТрикулачковий токарний патрон
Токарний різецьТокарний різець
Цифровий штангенциркуль 6 дюймівЦифровий штангенциркуль 6 дюймів
Ножиці по металуНожиці по металу
Слюсарні лещатаСлюсарні лещата
Розвідний ключРозвідний ключ
Набір шестигранних ключівНабір шестигранних ключів
7

Motor frame

Bolt a shorter angle frame 53 inside the saw frame, pivoted on the same rear cross bolt, and bolt the motor 51 under it with a V-belt pulley 50 in line with the arbor's. Hang its free end from a bolt 55 off a sleeve 56 on a rod 57 across the saw frame, with a spring 61 and washer 62 on the bolt above the motor frame and a nut 59 below. Fit the belt 52 and set its tension with the nut. Have the motor wired to a switch at the front.

Матеріали для цього кроку:

Кутник із м'якої сталіКутник із м'якої сталі1 штука
ЕлектродвигунЕлектродвигун1 штука
Шків клинового паса (профіль A)Шків клинового паса (профіль A)1 штука
Клиновий пас (переріз A)Клиновий пас (переріз A)1 штука
Круглий пруток з маловуглецевої сталіКруглий пруток з маловуглецевої сталі1 штука
Шпилька різьбоваШпилька різьбова1 штука
Coil SpringCoil Spring1 штука
Плоска шайбаПлоска шайба2 штук
Шестигранна гайкаШестигранна гайка2 штук
Набір шестигранних болтівНабір шестигранних болтів6 штук
Вимикач живленняВимикач живлення1 штука

Необхідні інструменти ({count})

Ножівка по металуНожівка по металу
Свердлильний верстатСвердлильний верстат
Набір сверделНабір свердел
Розвідний ключРозвідний ключ
Набір шестигранних ключівНабір шестигранних ключів
8

Fence and first cut

Fix a hardwood fence 63 across the top near its rear end, standing past both sides, held by hook bolts 64 that hook under steel flanges 66 screwed to the gussets, with nuts 67. Set the blade 10 mm above the board's thickness with the stem's nuts. Hold a board against the fence, start the motor and press the pedal: the saw comes back through the board. Let the pedal up and it returns.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини1 штука
Шпилька різьбоваШпилька різьбова1 штука
Шестигранна гайкаШестигранна гайка2 штук
Смуга з маловуглецевої сталіСмуга з маловуглецевої сталі1 штука
Шурупи по деревуШурупи по дереву8 штук

Необхідні інструменти ({count})

ЕлектролобзикЕлектролобзик
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Комбінований кутникКомбінований кутник
Захисні окуляриЗахисні окуляри
Захист слуху (навушники, SNR 30 дБ)Захист слуху (навушники, SNR 30 дБ)
9

Troubleshooting

Carriage saw troubleshooting.

Flow

Loading...
10

History and honest limits

**Harry O. Hall** of Murray, Utah, US 1,930,168, dated 10 October 1933, filed 21 March 1933. He claimed a top with a longitudinal slot, "a traveling carriage mounted beneath said top and movable longitudinally thereof", a saw frame pivoted on one cross bar and hung from the other on a stem with nuts above and below, and a motor frame hung from the saw frame on a bolt with a spring. His top is folded sheet metal on splayed legs; ours is plywood on pine. His balls are confined between the cross bolts and lugs; ours the same, in steel angle. He gives no sizes; every size here is ours.

Матеріали

27

Необхідні інструменти

22

За цим кресленням виготовляють

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...