Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Slotted-Gate Dash Churn: A Hand Wheel Turns a Crank Pin in the Slot of a Sliding Gate, Which Drives the Dash Up and Down
Buttercup

Створено

Buttercup

11. листопад 2026IE
6
0
0
0
0

Slotted-Gate Dash Churn: A Hand Wheel Turns a Crank Pin in the Slot of a Sliding Gate, Which Drives the Dash Up and Down

Henry A. Nevers and Charles Ross of Claremont, New Hampshire, received US 30,686, dated 20 November 1860, for a compact plunge churn on its own stand. A hand wheel on a shaft turns a disk whose crank pin runs in a horizontal slot cut in a wooden gate; the gate slides up and down in grooves in two standards and carries the dash rod, so turning the wheel works the dash evenly up and down. Pull one pin and the dasher comes free. The patent gives no sizes; every size here is ours.
Середній
About 2 days

Інструкції

1

Pin in a slot against a connecting rod

Завантаження блокнота Jupyter…
2

A wheel plunging the dash by a connecting rod, four months before

Paff drives his dash rod from a flywheel by a pitman. Nevers and Ross put the crank pin in a slot instead.
3

Read US 30,686

"Motion is communicated to the wheel G, and through the shaft F to the disk H, the pin c on which as it revolves plays in the slot d, in the gate I, by which means the gate is raised and lowered vertically and with it the rod J, and dash K, which agitates the cream as required."
4

Base A, standards C, C' and D, platform E

Glue up a hardwood base A 500 x 460 x 25 mm. Rout an 11 mm groove 11 deep down one face of two hardwood standards C, C' 40 x 40 x 830 mm and screw them upright on the base, grooves facing and their inner faces 320 mm apart, either side of where the churn stands. Screw a standard D 40 x 40 x 575 mm behind the churn, 220 mm from its centre. Screw a platform E 177 x 400 x 20 mm across from two cheek blocks on the backs of C, C' to the top of D, its top 575 mm above the base.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини3 штук
Столярний клейСтолярний клей1 штука
Шурупи по деревуШурупи по дереву30 штук

Необхідні інструменти ({count})

Циркулярний верстатЦиркулярний верстат
Ручний фрезерРучний фрезер
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Струбцина з напрямноюСтрубцина з напрямною
Набір викрутокНабір викруток
РулеткаРулетка
5

Bearings a, shaft F, disk H, pin c and wheel G

Screw two hardwood bearing blocks a 30 x 50 x 70 mm on the platform, 85 and 170 mm behind the gate's plane, bored 16.6 mm across 45 mm up. Run a 16 mm stainless shaft F 217 mm long through them, held by a shaft collar. Cut a hardwood disk H 180 mm across and 18 thick, fix it on the shaft's front end 40 mm from the gate's plane, and drive a 10 mm stainless pin c 72 mm long through it 60 mm from the centre so 54 mm stands out toward the gate. Cut a hardwood wheel G 240 mm across and 20 thick, fix it on the shaft's back end, and set a hardwood handle b 100 mm from its centre.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини1 штука
Пруток із нержавкої сталіПруток із нержавкої сталі2 штук
Shaft CollarShaft Collar1 штука
ШплінтШплінт2 штук
Шканти з твердої деревиниШканти з твердої деревини1 штука
Столярний клейСтолярний клей1 штука
Шурупи по деревуШурупи по дереву8 штук

Необхідні інструменти ({count})

Циркулярний верстатЦиркулярний верстат
КомпасКомпас
ЕлектролобзикЕлектролобзик
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Ножівка по металуНожівка по металу
Напилки (ручний напилок)Напилки (ручний напилок)
Набір викрутокНабір викруток
6

Gate I with slot d and tongues e

Glue up a hardwood gate I 320 x 200 x 22 mm and cut a slot d 10.5 mm wide and 132 mm long across it, its middle 100 mm above the gate's foot. Glue hardwood strips 10 x 10 mm along both upright edges as the tongues e. Glue a hardwood block 50 x 50 x 60 mm under the gate's foot, bored 25.6 mm up 51 mm for the dash rod, and bore it 6 mm across for the pin f. Slide the gate down between the standards, its tongues in the grooves, the crank pin in the slot.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини1 штука
Столярний клейСтолярний клей1 штука

Необхідні інструменти ({count})

Циркулярний верстатЦиркулярний верстат
Ручний фрезерРучний фрезер
Набір стамесок по деревуНабір стамесок по дереву
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Набір перових сверделНабір перових свердел
Струбцина з напрямноюСтрубцина з напрямною
7

Body B, cover L, dash rod J and dash K

Use a 20-litre food-grade bucket as the body B, standing between the standards. Cut a 12 mm HDPE cover L to its top, 304 mm across, with a 27 mm hole in the middle, saw it in two halves through the hole and screw a hardwood knob g on each. Cut a 220 mm HDPE disk as the dash K and screw it to the foot of a 25 mm hardwood dash rod J 378 mm long. Put the dash in the bucket, the cover halves round the rod, push the rod up into the gate's block and pin it with a 6 mm stainless pin f.

Матеріали для цього кроку:

Відро на 20 літрівВідро на 20 літрів1 штука
Лист ПЕВГЛист ПЕВГ1 штука
Шканти з твердої деревиниШканти з твердої деревини1 штука
Пруток із нержавкої сталіПруток із нержавкої сталі1 штука
Шурупи по деревуШурупи по дереву6 штук

Необхідні інструменти ({count})

КомпасКомпас
ЕлектролобзикЕлектролобзик
Набір перових сверделНабір перових свердел
Акумуляторний дрильАкумуляторний дриль
Ножівка по металуНожівка по металу
Набір викрутокНабір викруток
8

The build in 3D

FreeCAD model of this build, the bucket cut open: the base, the grooved standards and the gate with its slot and tongues, the platform with its bearings, the shaft, disk and crank pin, the wheel and handle, the dash rod and dash.
Файл дизайнуBLENDCC0 - Free
9

Churn

Pour about 10 litres of heavy cream at about 15 °C, checked with the thermometer, into the bucket before fitting the cover. Turn the wheel steadily by its handle, timing it. When the butter comes, lift off the cover halves, pull the pin f, lift out the dash, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

Матеріали для цього кроку:

Жирні вершкиЖирні вершки10 l
Крупна морська сільКрупна морська сіль1 штука
ВодаВода1 штука

Необхідні інструменти ({count})

Термометр зі щупом, що лишається в стравіТермометр зі щупом, що лишається в страві
СекундомірСекундомір
Цифрові кухонні вагиЦифрові кухонні ваги
Велика миска з нержавкої сталіВелика миска з нержавкої сталі
10

Troubleshooting

Slotted-gate churn troubleshooting.

Flow

Loading...
11

History and honest limits

**Henry A. Nevers** and **Charles Ross** of Claremont, Sullivan County, New Hampshire, US 30,686, 20 November 1860, "Churn". They claimed "the combined arrangement of the driving shaft F, face plate and crank pin H, c, with the vertically reciprocating carriage I, provided with a horizontal slot d, and the rod J, of the dasher". Their wheel was spoked and their gate's top scalloped; ours are plain wooden discs and a plain gate, and our churn body is a bucket. The patent gives no sizes; every size here is ours.

Матеріали

12

Необхідні інструменти

17

Файли дизайну

1

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...