Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Balance-Wheel Churn Frame: A Weighted Wheel Drives the Dash Up and Down and Its Pitched Blades Make It Revolve
Buttercup

Створено

Buttercup

11. листопад 2026IE
5
0
0
0
0

Balance-Wheel Churn Frame: A Weighted Wheel Drives the Dash Up and Down and Its Pitched Blades Make It Revolve

Nathan D. Ross of Braintrim, Pennsylvania, received US 28,607, dated 5 June 1860, for a churn. A tall timber frame carries a shaft with a heavy balance wheel at one end and a crank at the other; a rod from an adjustable wrist on the wheel drives the dash staff up and down through a guide. The staff joins the churn handle by a swivel, and the dashers' blades all stand at one angle, so the dash turns right and left as it is driven through the cream. The frame's, shaft's, wheel's and dasher pieces' sizes are the patent's own, given as "about"; all others are ours.
Просунутий
About 3 days

Інструкції

1

The patent's sizes, and a wheel of about 30 pounds

Завантаження блокнота Jupyter…
2

A crank frame over an ordinary churn, one week before

Evans gears his crank up. Ross gives his a heavy balance wheel and an adjustable stroke.
3

Read US 28,607

"The nature of my invention consists in lengthening or shortening the stroke and lowering and raising the dash so as to give it the right position in the churn at the same time giving the dash an independent revolving motion to the right and left and giving the operator power over the work to be done."
4

Frame A, cap G and braces

From 51 mm square timber (the patent's two inches) cut two front posts about 1.83 m long and two back posts about 0.91 m. Set the feet about 0.91 m apart; lean the front posts in so they meet at the top, and the back posts at the same angle. Join front and back posts on each side with two side cross pieces about 0.81 m between shoulders, at 300 and 860 mm up, and front and back with cross pieces at the same heights, cut to the bevel. On the top of the long posts fix a cap G reaching 410 mm forward, bored 32 mm near its end for the staff, and brace it with two timbers down to near the tops of the short posts.

Матеріали для цього кроку:

Сосновий пиломатеріалСосновий пиломатеріал6 штук
Столярний клейСтолярний клей1 штука
Шурупи по деревуШурупи по дереву40 штук
Болт із півкруглою головкоюБолт із півкруглою головкою8 штук
Самоконтрувальна гайка з нейлоновим кільцемСамоконтрувальна гайка з нейлоновим кільцем8 штук

Необхідні інструменти ({count})

Циркулярний верстатЦиркулярний верстат
Набір стамесок по деревуНабір стамесок по дереву
ТранспортирТранспортир
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Набір перових сверделНабір перових свердел
Струбцина з напрямноюСтрубцина з напрямною
Розвідний ключРозвідний ключ
РулеткаРулетка
5

Shaft K, balance wheel C and slide crank F

Bolt a hardwood bearing block bored 26 mm to the middle of each top front and back cross piece, and pass a 25 mm mild steel shaft K through them (the patent's about one inch). Glue two 18 mm plywood discs into a wheel 600 mm across with a rim 50 mm wide and four arms, and screw a ring of 60 x 12 mm mild steel flat bar round it so it weighs about 14 kg, near the patent's 30 pounds. Cut a slot 13 mm wide from 60 to 140 mm out along one arm for the wrist, a 16 mm bolt with a nut. Fix the wheel on the shaft's front end. On the back end fix a crank F of flat bar with three holes for the handle, so it can be lengthened or shortened.

Матеріали для цього кроку:

Дошка з твердої деревиниДошка з твердої деревини1 штука
Круглий пруток з маловуглецевої сталіКруглий пруток з маловуглецевої сталі1 штука
Лист фанериЛист фанери1 штука
Столярний клейСтолярний клей1 штука
Смуга з маловуглецевої сталіСмуга з маловуглецевої сталі2 штук
Шурупи по деревуШурупи по дереву24 штук
Болт із півкруглою головкоюБолт із півкруглою головкою4 штук
Самоконтрувальна гайка з нейлоновим кільцемСамоконтрувальна гайка з нейлоновим кільцем4 штук
Shaft CollarShaft Collar2 штук
Шканти з твердої деревиниШканти з твердої деревини1 штука

Необхідні інструменти ({count})

ЕлектролобзикЕлектролобзик
Струбцина з напрямноюСтрубцина з напрямною
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Ножівка по металуНожівка по металу
Слюсарні лещатаСлюсарні лещата
Напилки (ручний напилок)Напилки (ручний напилок)
Розвідний ключРозвідний ключ
6

Rod E, staff D, socket I, socket H and swivel J

Cut a 32 mm hardwood staff D about 1.25 m long and pass it up through the cap. Make a hardwood socket I to slide on it, with a lug for the rod and a thumb screw (threaded rod, nut and wing nut) to fix it. Cut a hardwood rod E 730 mm between holes, from the wrist to the lug. Fit a hardwood socket H on the staff's foot, bored 16.5 mm, with a thumb screw through its side; turn the top of the churn handle L down to a 16 mm pin with a groove, so the thumb screw rides in the groove and the handle turns freely: the swivel J.

Матеріали для цього кроку:

Шканти з твердої деревиниШканти з твердої деревини2 штук
Дошка з твердої деревиниДошка з твердої деревини1 штука
Шпилька різьбоваШпилька різьбова1 штука
Шестигранна гайкаШестигранна гайка2 штук
Гайка-баранецьГайка-баранець2 штук
Болт із півкруглою головкоюБолт із півкруглою головкою2 штук
Самоконтрувальна гайка з нейлоновим кільцемСамоконтрувальна гайка з нейлоновим кільцем2 штук
Столярний клейСтолярний клей1 штука

Необхідні інструменти ({count})

Циркулярний верстатЦиркулярний верстат
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Набір перових сверделНабір перових свердел
Ножівка по металуНожівка по металу
Напилки (ручний напилок)Напилки (ручний напилок)
Розвідний ключРозвідний ключ
7

Handle L and dashers M

Cut a 28 mm hardwood handle 420 mm long. For each dasher halve together two hardwood pieces 38 x 19 mm (the patent's 1 1/2 x 3/4 inch), 260 long, at right angles, and plane each blade on both sides down to about 6 mm at its edges, every blade bevelled the same way so they all stand on one angle, about 30 degrees. Fix two such dashers on the handle's foot, 60 mm apart.

Матеріали для цього кроку:

Шканти з твердої деревиниШканти з твердої деревини1 штука
Дошка з твердої деревиниДошка з твердої деревини1 штука
Столярний клейСтолярний клей1 штука
Пруток із нержавкої сталіПруток із нержавкої сталі1 штука
ШплінтШплінт2 штук

Необхідні інструменти ({count})

Циркулярний верстатЦиркулярний верстат
Набір стамесок по деревуНабір стамесок по дереву
Ручний рубанокРучний рубанок
ТранспортирТранспортир
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
8

The build in 3D

FreeCAD model of this build: the frame with its leaning posts, cap G and braces, the shaft K on its bearings with the balance wheel and slide crank, the rod E from the wrist to the socket I on the staff, the swivel and handle with two pitched dashers in the bucket, cut open.
Файл дизайнуBLENDCC0 - Free
9

Churn

Pour about 10 litres of heavy cream at about 15 °C, checked with the thermometer, into the bucket, stand it under the staff with the handle through its lid, and join handle and staff at the swivel. Set the socket I on the staff so the dash just clears the bottom at the low point, and the wrist for the stroke you want. Turn the crank F, timing it; the wheel carries the stroke round and the dash turns as it goes. When the butter comes, loosen the swivel's thumb screw, lift the handle out, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

Матеріали для цього кроку:

Жирні вершкиЖирні вершки10 l
Крупна морська сільКрупна морська сіль1 штука
ВодаВода1 штука
Відро на 20 літрівВідро на 20 літрів1 штука

Необхідні інструменти ({count})

Термометр зі щупом, що лишається в стравіТермометр зі щупом, що лишається в страві
СекундомірСекундомір
Цифрові кухонні вагиЦифрові кухонні ваги
Велика миска з нержавкої сталіВелика миска з нержавкої сталі
10

Troubleshooting

Balance-wheel churn troubleshooting.

Flow

Loading...
11

History and honest limits

**Nathan D. Ross** of Braintrim, Wyoming County, Pennsylvania, US 28,607, 5 June 1860, "Churn". He did not claim the up-and-down motion of dasher and handle, but the revolving of the dashers and handle by the series of dashers and blades. The frame, shaft, wheel and dasher-piece sizes are his, given as "about"; he gives the wheel's size and weight but not its material; ours is plywood with a steel ring; the bucket, stroke, rod and blade angle are ours.

Матеріали

20

Необхідні інструменти

18

Файли дизайну

1

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...