Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Tube-Track Pedal Saw Table: Any Portable Saw Clamped Upside Down on a Carriage Rolling Inside Slotted Tubes (Tomlinson & Bearden, 1931)
Forge

Створено

Forge

13. листопад 2026NO
6
0
0
0
0

Tube-Track Pedal Saw Table: Any Portable Saw Clamped Upside Down on a Carriage Rolling Inside Slotted Tubes (Tomlinson & Bearden, 1931)

William A. Tomlinson and Howell B. Bearden of Phoenix, Arizona, received US 1,813,783, dated 7 July 1931, for a table that turns any portable power saw into a table saw. The saw is clamped upside down on a carriage, its blade through the slot of a top hinged at the rear. The carriage rolls on ball-bearing rollers inside two steel tubes slotted along their undersides. A pedal pushes it forward through the work, leaving both hands free, and a spring brings it back. With the pedal left alone it works as a fixed saw, and the saw unbolts for hand use. The patent gives no sizes; every size here is ours.
Просунутий
About 4 days

Інструкції

1

Pedal, link and travel

Завантаження блокнота Jupyter…
2

Read US 1,813,783

"By using the pedal in the manner above set forth both hands of the operator will be free for manipulating the work, which is especially desirable when pattern work is to be sawed."
3

Angle-iron frame

Bolt a frame of steel angle 900 x 500 mm, 850 high: four corner legs 1, side and end bars 2, 3 halfway up and 4, 5 at the top, flat-bar diagonal braces 6 at the top corners, a cross bar 7 between the rear legs above the middle bars, and a cross bar 8 between the front legs at the bottom. Drill a vertical row of 9 mm holes 13, 25 mm apart, near the top of each leg, for the track hangers.

Матеріали для цього кроку:

Кутник із м'якої сталіКутник із м'якої сталі6 штук
Смуга з маловуглецевої сталіСмуга з маловуглецевої сталі1 штука
Набір шестигранних болтівНабір шестигранних болтів40 штук
Шестигранна гайкаШестигранна гайка40 штук
Плоска шайбаПлоска шайба40 штук

Необхідні інструменти ({count})

Ножівка по металуНожівка по металу
Кутова шліфмашинаКутова шліфмашина
Свердлильний верстатСвердлильний верстат
Набір сверделНабір свердел
КернерКернер
Комбінований кутникКомбінований кутник
РулеткаРулетка
Розвідний ключРозвідний ключ
Захисні окуляриЗахисні окуляри
4

Slotted tube tracks

Cut two 900 mm lengths of 42 mm steel tube 9, 10 and cut a 10 mm slot 14 along the underside of each, stopping 20 mm short of the ends; file the slot's edges smooth. Bolt a flat-bar hanger 11 to each end of each tube and hang the tubes along the frame's sides from the legs with bolts 12 through the row of holes, at the height that suits your saw. Put a short coil spring 39 in each end of each tube as a buffer.

Матеріали для цього кроку:

Кругла труба з м'якої сталіКругла труба з м'якої сталі2 штук
Смуга з маловуглецевої сталіСмуга з маловуглецевої сталі1 штука
Coil SpringCoil Spring4 штук
Набір шестигранних болтівНабір шестигранних болтів8 штук
Шестигранна гайкаШестигранна гайка8 штук

Необхідні інструменти ({count})

Ножівка по металуНожівка по металу
Кутова шліфмашинаКутова шліфмашина
Набір напилківНабір напилків
Слюсарні лещатаСлюсарні лещата
Свердлильний верстатСвердлильний верстат
Набір сверделНабір свердел
Розвідний ключРозвідний ключ
Цифровий штангенциркуль 6 дюймівЦифровий штангенциркуль 6 дюймів
Захисні окуляриЗахисні окуляри
5

Carriage and rollers

Cut the carriage 30 from 5 mm steel plate, as wide as between the tubes. At each corner bolt an upright flat-bar standard 31 that reaches up through a tube's slot, and on its top a short bar 33 across inside the tube carrying a 22 mm ball bearing 32 at each end on an M8 bolt with a lock nut. Slide the rollers into the tubes from the ends, the standards hanging down through the slots, and bolt them to the carriage.

Матеріали для цього кроку:

Лист маловуглецевої сталіЛист маловуглецевої сталі1 штука
Смуга з маловуглецевої сталіСмуга з маловуглецевої сталі1 штука
Кульковий підшипникКульковий підшипник8 штук
Набір шестигранних болтівНабір шестигранних болтів16 штук
Самоконтрувальна гайка з нейлоновим кільцемСамоконтрувальна гайка з нейлоновим кільцем8 штук
Плоска шайбаПлоска шайба16 штук

Необхідні інструменти ({count})

Ножівка по металуНожівка по металу
Кутова шліфмашинаКутова шліфмашина
Свердлильний верстатСвердлильний верстат
Набір сверделНабір свердел
Набір напилківНабір напилків
Слюсарні лещатаСлюсарні лещата
Розвідний ключРозвідний ключ
6

Pedal and springs

Pivot a lever 21 of steel flat bar on the front bottom cross bar 8, with an arm 22 to the side carrying the pedal 20 and a brace 23 from arm to lever. Join the lever's top to the carriage's front with a flat-bar link 24. Hook a return spring 25a from the rear cross bar 7 to the lever partway up.

Матеріали для цього кроку:

Смуга з маловуглецевої сталіСмуга з маловуглецевої сталі2 штук
Круглий пруток з маловуглецевої сталіКруглий пруток з маловуглецевої сталі1 штука
Пружина розтягуПружина розтягу1 штука
Набір шестигранних болтівНабір шестигранних болтів4 штук
Самоконтрувальна гайка з нейлоновим кільцемСамоконтрувальна гайка з нейлоновим кільцем4 штук

Необхідні інструменти ({count})

Ножівка по металуНожівка по металу
Свердлильний верстатСвердлильний верстат
Набір сверделНабір свердел
Слюсарні лещатаСлюсарні лещата
Розвідний ключРозвідний ключ
7

Mount the saw and the top

Turn the circular saw upside down on the carriage and bolt it by its base plate with bolts and wing nuts, so it lifts off for hand use; his T-bolt 34 and hook bolts 36 gripped the saw's handles, which modern saws do not suit. Make the top 42 of plywood on a steel angle frame 44, slotted along the blade's path, and hinge its rear edge to the frame so it swings up to reach the saw. Fit a catch 47 to lock it down and a folding flat-bar brace 49 to prop it up.

Матеріали для цього кроку:

Дискова пилаДискова пила1 штука
Набір шестигранних болтівНабір шестигранних болтів4 штук
Гайка-баранецьГайка-баранець4 штук
Лист фанериЛист фанери1 штука
Кутник із м'якої сталіКутник із м'якої сталі1 штука
Карткова завісаКарткова завіса2 штук
Гачок і петляГачок і петля1 штука
Смуга з маловуглецевої сталіСмуга з маловуглецевої сталі1 штука
Шурупи по деревуШурупи по дереву16 штук

Необхідні інструменти ({count})

ЕлектролобзикЕлектролобзик
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Ножівка по металуНожівка по металу
Розвідний ключРозвідний ключ
Комбінований кутникКомбінований кутник
8

Cut

Lock the top down. Set the saw's depth so the blade stands 10 mm above the board. Place the board on the top in front of the blade, start the saw and press the pedal: the carriage rolls the running blade through it while both hands hold the work. Let the pedal up and the spring returns it. For ripping, leave the carriage still and feed the board.

Необхідні інструменти ({count})

Захисні окуляриЗахисні окуляри
Захист слуху (навушники, SNR 30 дБ)Захист слуху (навушники, SNR 30 дБ)
9

Troubleshooting

Tube-track saw table troubleshooting.

Flow

Loading...
10

History and honest limits

**William A. Tomlinson** and **Howell B. Bearden** of Phoenix, Arizona, US 1,813,783, dated 7 July 1931, filed 5 December 1928. They claimed a top with a slot, "laterally spaced longitudinally extending tubular tracks" below it, "slotted longitudinally on their lower faces", and a saw carriage with upstanding roller-carrying hangers in the tracks, their shanks through the slots. Their saw is held by its handles; ours by its base plate. Their frame is angle iron, as ours. They give no sizes; every size here is ours.

Матеріали

18

Необхідні інструменти

15

За цим кресленням виготовляють

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...