Співпраця
МИСТЕЦТВО
КРАСА ТА ЗДОРОВ'Я
РЕМЕСЛО
КУЛЬТУРА ТА ІСТОРІЯ
РОЗВАГИ
СЕРЕДОВИЩЕ
ЇЖА ТА НАПІЇ
ЗБОРНА ІНЖЕНЕРІЯ
НАУК
СПОРТ
ТЕХНОЛОГІЯ
НОСИМО
Sliding-Table Saw That Switches Itself: A Hand Saw Under a Table on Balls, Turned On and Off by the Stroke (Tracy, 1941)
Forge

Створено

Forge

13. листопад 2026NO
7
0
0
0
0

Sliding-Table Saw That Switches Itself: A Hand Saw Under a Table on Balls, Turned On and Off by the Stroke (Tracy, 1941)

Mearl V. Tracy of Sacramento received US 2,260,421, dated 28 October 1941, for a light table saw to take onto a building job. An ordinary electric hand saw hangs under a table that slides on steel balls in channels. The work is held against a fixed fence and the table carries the saw through it. A springy finger on the table trips a snap switch, starting the saw just before it reaches the work and stopping it as the table comes back. One fence on a graduated plate serves as rip fence and mitre gauge. The patent gives no sizes; every size here is ours, and our box is plywood where his is sheet metal.
Середній
About 3 days

Інструкції

1

Where the switch must trip

Завантаження блокнота Jupyter…
2

Read US 2,260,421

"The finger 25 is so disposed as to engage trigger 24 and close the switch when the table is advanced and just before the saw reaches the work under which the table slides, and to reengage the trigger and open the switch as the table retracts and approaches a fully retracted position."
3

The box frame

Make an open-topped box of 18 mm plywood 900 mm long, 450 wide and 300 high, the end panels 2 standing 40 mm lower than the sides 1, glued and screwed. Bolt a steel channel section 5 along the inside top of each side, its open face inwards, as his channels on the beams 4.

Матеріали для цього кроку:

Лист фанериЛист фанери1 штука
Сталевий швелерСталевий швелер2 штук
Набір шестигранних болтівНабір шестигранних болтів8 штук
Шестигранна гайкаШестигранна гайка8 штук
Шурупи по деревуШурупи по дереву30 штук
Столярний клейСтолярний клей1 штука

Необхідні інструменти ({count})

ЕлектролобзикЕлектролобзик
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Струбцина з напрямноюСтрубцина з напрямною
Комбінований кутникКомбінований кутник
РулеткаРулетка
Ножівка по металуНожівка по металу
Розвідний ключРозвідний ключ
4

The sliding table

Cut the table 6 from 18 mm plywood 600 x 400 mm with a saw slot 15 down its middle, and bolt a steel channel section 7 along each side edge, its open face outwards opposite the box's channel, reaching 100 mm past the table's front for the handle. Lay 10 mm steel balls 8 between each pair of opposed channels, three a side, spaced along, and slide the table in so it runs level with the box's top. Fit a hardwood handle 9 across the angles' front ends, and stops 10, 11 and 12 to limit the stroke to 450 mm.

Матеріали для цього кроку:

Лист фанериЛист фанери1 штука
Сталевий швелерСталевий швелер2 штук
Кулькові підшипникиКулькові підшипники1 штука
Дошка з твердої деревиниДошка з твердої деревини1 штука
Набір шестигранних болтівНабір шестигранних болтів8 штук
Шестигранна гайкаШестигранна гайка8 штук
Шурупи по деревуШурупи по дереву12 штук

Необхідні інструменти ({count})

ЕлектролобзикЕлектролобзик
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Ножівка по металуНожівка по металу
Набір напилківНабір напилків
Розвідний ключРозвідний ключ
Комбінований кутникКомбінований кутник
5

Hang the saw under the table

Bolt the circular saw by its own base plate under the table, the blade up through the slot, the saw's depth set so the blade stands 10 mm above the thickest work. For angle cuts use the saw's own bevel adjustment, which does what his arcuate bracket 17 did. Tape or lock the saw's trigger on, so the new switch alone controls it.

Матеріали для цього кроку:

Дискова пилаДискова пила1 штука
Набір шестигранних болтівНабір шестигранних болтів4 штук

Необхідні інструменти ({count})

Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Розвідний ключРозвідний ключ
Комбінований кутникКомбінований кутник
6

The self-acting switch

Screw a lever microswitch rated for the saw's current inside one side panel, its lever 24 pointing up into the path of the table, with an outlet for the saw's plug and a supply cord through the panel, as his switch box 22 and socket; have it wired by an electrician. Bend a finger 25 of spring steel and screw it on a bracket 26 under the table, set so that, as the table goes forward, it flips the lever on 60 mm into the stroke, and as the table comes back it flips it off 40 mm before the end. Check it with the saw unplugged: you should hear the click each way.

Матеріали для цього кроку:

Мікроперемикач (із важільцем)Мікроперемикач (із важільцем)1 штука
Смуга пружинної сталіСмуга пружинної сталі1 штука
Смуга з маловуглецевої сталіСмуга з маловуглецевої сталі1 штука
Шурупи по деревуШурупи по дереву6 штук

Необхідні інструменти ({count})

Ножиці по металуНожиці по металу
Слюсарні лещатаСлюсарні лещата
Акумуляторний дрильАкумуляторний дриль
Набір сверделНабір свердел
Набір викрутокНабір викруток
7

Rip fence and mitre gauge

Cut a half-round steel plate 27 to lie over the front of the box beside the saw, turn its straight edge up as a flange 28 and bolt a hardwood fence 29 to it, notched 30 for the blade. Pivot a link 31 on top of the plate and a link 32 under it at the centre of its arc; pivot a third link 33 on 31's end; take 32 and 33 back to a flange on the side of the box. Mark the plate in degrees and drill rows of holes along the arcs, and set the fence with a pin through link 31 into a hole, clamped by two wing-nut clamps 35, 36.

Матеріали для цього кроку:

Лист маловуглецевої сталіЛист маловуглецевої сталі1 штука
Дошка з твердої деревиниДошка з твердої деревини1 штука
Смуга з маловуглецевої сталіСмуга з маловуглецевої сталі2 штук
Круглий пруток з маловуглецевої сталіКруглий пруток з маловуглецевої сталі1 штука
Набір шестигранних болтівНабір шестигранних болтів6 штук
Гайка-баранецьГайка-баранець2 штук

Необхідні інструменти ({count})

Ножиці по металуНожиці по металу
Ножівка по металуНожівка по металу
Слюсарні лещатаСлюсарні лещата
Свердлильний верстатСвердлильний верстат
Набір сверделНабір свердел
ТранспортирТранспортир
РисувалкаРисувалка
КернерКернер
Набір напилківНабір напилків
8

Cut

With the table fully back, hold a board against the fence with one hand and push the handle with the other. The saw starts by itself before the blade reaches the board, cuts through, and stops as you bring the table back.

Необхідні інструменти ({count})

Захисні окуляриЗахисні окуляри
Захист слуху (навушники, SNR 30 дБ)Захист слуху (навушники, SNR 30 дБ)
9

Troubleshooting

Sliding table saw troubleshooting.

Flow

Loading...
10

History and honest limits

**Mearl V. Tracy** of Sacramento, California, assignor of one-half to Marion M. Tracy, US 2,260,421, dated 28 October 1941, filed 18 April 1938. His one claim is the switch: a snap switch with a trigger moved one way or the other by "a resilient finger mounted on the table" that then passes and leaves the trigger, near but before each end of the stroke. He removed the hand saw's shoe and fixed its mounting block on an arcuately slotted bracket; modern saws differ, so we mount it by its base plate and use its own bevel adjustment. His box is sheet metal with the channels on bent beams; ours is plywood with steel channel sections. He gives no sizes; every size here is ours.

Матеріали

15

Необхідні інструменти

18

За цим кресленням виготовляють

CC0 Суспільне надбання

Це креслення випущено під ліцензією CC0. Ви можете вільно копіювати, змінювати, поширювати та використовувати цю роботу для будь-яких цілей без запиту дозволу.

Підтримайте мейкера, купуючи продукти через його креслення, де він отримує Комісію мейкера встановлену вендорами, або створіть нову ітерацію цього креслення та включіть його як зв'язок у власне креслення для розподілу доходу.

Обговорення

(0)

Увійти щоб приєднатися до обговорення

Завантаження коментарів...