Collaboration
ART
BEAUTY & WELLNESS
CRAFT
CULTURE & HISTORY
ENTERTAINMENT
ENVIRONMENT
FOOD & DRINKS
REVERSE ENGINEERING
SCIENCES
SPORTS
TECHNOLOGY
WEARABLES
Ore Crushing Rolls: Hard Shells on Soft Iron Cores, One Roll in Spring-Loaded Boxes, Gap Set by Shims (Richards, Ore Dressing, 1903)
Forge

Created by

Forge

15. November 2026NO
2
0
0
0
0

Ore Crushing Rolls: Hard Shells on Soft Iron Cores, One Roll in Spring-Loaded Boxes, Gap Set by Shims (Richards, Ore Dressing, 1903)

The crushing rolls that took ore from the jaw breaker in a 1900s mill, as Robert Richards described them: two shafts on one cast-iron frame, each carrying a soft-iron core with a replaceable hard shell; one runs in fixed boxes, the other in movable boxes pushed toward it by a nest of steel springs that yields like a safety valve; shims set the gap. Little fines, ideal for soft brittle ores.
Advanced
Weeks (castings and machining)

Instructions

1

His figures

Loading Jupyter Notebook...
2

Read Richards

"The ore is therefore broken by compression."
3

Frame and shafts

Cast the frame as one piece, both sides joined by end pieces, so settling of the building can't throw the shafts out of line (make it in two parts only if it must travel by mule). Turn two shafts of mild steel or wrought iron, each on two bearings.

Materials for this step:

Iron CastingsIron Castings1 piece
Steel ShaftSteel Shaft1 piece

Tools needed:

Foundry LadleFoundry Ladle
Metal LatheMetal Lathe
Block and TackleBlock and Tackle
4

Cores and shells

Force a soft cast-iron core onto each shaft. Krom's way (Fig. 37): two slightly conical half-cores, one shrunk on for good, the other split on one side and drawn in by four draw bolts; half-cores no wider than 4-5 in. Cast hard shells 2-5½ in. thick (chilled iron or steel), with wrought-iron staves cast in if chilled so the slightly conical inside can be turned to fit; turn the face true.

Materials for this step:

Iron CastingsIron Castings1 piece
Wrought Iron BarWrought Iron Bar1 piece
Hex Bolt AssortmentHex Bolt Assortment1 piece

Tools needed:

Metal LatheMetal Lathe
Foundry LadleFoundry Ladle
5

Boxes, springs and shims

Mount one shaft in fixed boxes and the other in movable ones, both babbitted, with shields and a cotton-waste groove against grit. Put a nest of steel spiral springs outside the fixed pillow block, with bolts carrying the force to the movable box, equal on both sides, compressed between plates by two compression bolts. Set the gap with shims and keep them in: the springs should only give when a hard lump comes through.

Materials for this step:

Coil SpringCoil Spring1 piece
Unknown MetalUnknown Metal1 piece
Hex Bolt AssortmentHex Bolt Assortment1 piece
Iron CastingsIron Castings1 piece

Tools needed:

Spanner SetSpanner Set
Metal LatheMetal Lathe
6

Drive and run

Drive by belt and pulley (or gears and pulleys for slow coarse work). Feed lumps no bigger than about 1½ in. (4 cm), 2½ in. at most, evenly with a feeder so a rush of ore does not choke it.

Materials for this step:

PulleyPulley1 piece
Drive BeltDrive Belt1 piece

Tools needed:

Spanner SetSpanner Set
7

Troubleshooting

Crushing rolls troubleshooting.

Flow

Loading...
8

History and honest limits

From Robert H. Richards, *Ore Dressing* vol. I (1903), Chapter III, §§ 71-85, pp. 62-74, Fig. 37 and Tables 34-39 (checked on the archive.org scan oredressing01richuoft; p. 62 from its text layer). Rubber springs were the cheap short-life option; levers and weights had nearly gone out of use. Richards surveys machines from many makers rather than one design: building from castings, the size and metric are ours, and the babbitt alloy has no head yet.

Materials

8

Tools Required

4

CC0 Public Domain

This blueprint is released under CC0. You are free to copy, modify, distribute, and use this work for any purpose, without asking permission.

Support the Maker by purchasing products through their Blueprint where they earn a Maker Commission set by Vendors, or create a new iteration of this Blueprint and include it as a connection in your own Blueprint to share revenue.

Discussion

(0)

Log in to join the discussion

Loading comments...