NGHỆ THUẬT
LÀM ĐẸP VÀ SỨC KHỎE
THỦ CÔNG
VĂN HÓA VÀ LỊCH SỬ
GIẢI TRÍ
MÔI TRƯỜNG
THỰC PHẨM VÀ ĐỒ UỐNG
TƯƠNG LAI XANH
KỸ THUẬT NGƯỢC
KHOA HỌC
THỂ THAO
CÔNG NGHỆ
THIẾT BỊ ĐEO
Making Clay Beads — Hand-Rolled and Pit-Fired Ornaments
Clay

Tạo bởi

Clay

25. tháng Năm 2026DK
0
0
0
0
0

Making Clay Beads — Hand-Rolled and Pit-Fired Ornaments

Clay beads are among the oldest decorative objects made by humans — fired clay beads from Dolní Věstonice in the Czech Republic date to approximately 26,000 years ago, making them some of the earliest known ceramics. Unlike shell or bone beads that require drilling through hard material, clay beads are formed soft and pierced with a stick before firing, making them far easier to produce in quantity. Beads served as personal ornament, trade goods, counting tokens, and markers of social status across all prehistoric cultures. The process is simple: prepare clay, roll beads, pierce holes, dry, fire. The key challenge is preventing the beads from cracking during drying and firing — uniform thickness, thorough drying, and slow temperature increase are essential.
Cơ bản
2-3 hours (plus firing)

Hướng dẫn

1

Gather and Clean the Clay

Gather fine-grained clay and remove stones, roots, and debris by hand.

Vật liệu cho bước này:

Raw Clay from RiverbankRaw Clay from Riverbank1 cái
2

Knead the Clay Thoroughly

Knead the clay thoroughly to remove air bubbles — wedging on a flat stone works well.
3

Add Temper (Optional)

Optionally mix in a small amount of fine sand (10-15%) as temper to reduce cracking.
4

Roll the Beads

Pinch off a small piece of clay and roll it between your palms into a smooth sphere (8-15mm diameter).
5

Pierce the Centre Hole

Pierce the centre of each bead with a thin stick, twig, or bone awl — push through from one side, then ream from both sides.

Công cụ cần thiết:

Bone AwlBone Awl
6

Size the Hole for Cordage

The hole should be large enough for a cord (2-3mm diameter).
7

Leave the Stick in During Drying

Leave the stick in place while drying to keep the hole open and prevent it from closing.
8

Dry Slowly in Shade

Set beads on a dry surface in shade and dry slowly for 2-3 days — fast drying causes cracks.
9

Remove the Sticks

Remove the sticks once the clay is leather-hard.
10

Add Surface Decoration (Optional)

Optional: press patterns into the bead surface with a pointed stick or stamp with cord impressions before drying.
11

Fire in a Pit Kiln

Fire the beads in a pit kiln: place in the coals, cover with fuel, burn for 2-3 hours at 600-800°C, and allow to cool slowly in the ash.

Vật liệu

1

Công cụ yêu cầu

1

Vật liệu bản thiết kế liên kết

CC0 Phạm vi công cộng

Bản thiết kế này được phát hành theo CC0. Bạn tự do sao chép, sửa đổi, phân phối và sử dụng cho bất kỳ mục đích nào mà không cần xin phép.

Hỗ trợ nhà sáng tạo bằng cách mua sản phẩm qua bản thiết kế, nơi họ nhận Hoa hồng nhà sáng tạo do nhà bán hàng đặt, hoặc tạo phiên bản mới và kết nối trong bản thiết kế riêng để chia sẻ doanh thu.

Thảo luận

(0)

Đăng nhập để tham gia thảo luận

Đang tải bình luận...