NGHỆ THUẬT
LÀM ĐẸP VÀ SỨC KHỎE
THỦ CÔNG
VĂN HÓA VÀ LỊCH SỬ
GIẢI TRÍ
MÔI TRƯỜNG
THỰC PHẨM VÀ ĐỒ UỐNG
KỸ THUẬT NGƯỢC
KHOA HỌC
THỂ THAO
CÔNG NGHỆ
THIẾT BỊ ĐEO

Quarter-Twist Spiral Dash Churn: Wings Twisted Between Arms Set at Right Angles
The Hights made the wings of a horizontal box-churn dash into a screw.
Cornelius R. Hight and John Hight of Geneva, Illinois, received US 7,490, dated 9 July 1850, for a "reacting spiral revolving dash" in a box churn: a shaft with four arms, those at one end at right angles to those at the other, and two wings fastened from arm to arm "so as to produce a quarter twist in the wings as they extend along the shaft." Its revolution produces "opposite currents, in the cream"; reversed, "the butter collects at the ends of the wings."
This rung works out the wings' pitch, then prints the dash in one piece, fits it in a box, and makes butter.
Trung cấp
About 3 hours, plus printing
Hướng dẫn
1
1
The quarter twist
The quarter twist
Đang tải sổ tay Jupyter…
2
2
Oblique wings on a horizontal arbor before it
Oblique wings on a horizontal arbor before it
The embedded blueprint sets straight wings at 30° to the axle. The Hights twist theirs a quarter turn from end to end, like a screw.
3
3
Read US 7,490
Read US 7,490
"The peculiar construction of the dash, consists in setting the arms to which the wings are attached, at right angles, upon opposite sides of the shaft, so as to produce a quarter twist in the wings as they extend along the shaft from one arm to the other."
4
4
Print the dash
Print the dash
Print the dash on end in one piece with supports (/uploads/blueprints/quarter-twist-spiral-dash-churn-dash.stl): shaft, four arms and two wings each twisted a quarter turn. Print the crank arm (/uploads/blueprints/quarter-twist-spiral-dash-churn-crank-arm.stl). Print in PETG at 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
Vật liệu cho bước này:
Sợi in PETG1 cáiCông cụ cần thiết:
Máy in 3D sợi nhựa (FDM)5
5
Fit the box
Fit the box
Take a food-safe box about 220 × 150 × 160 mm, its proportions close to his 18 × 12 × 13 inches. Drill both ends on the axis 80 mm up. Push a 10 mm square hardwood shaft through one end, the dash and the other end, with a leather washer at each.
Vật liệu cho bước này:
Thùng chứa cấp thực phẩm1 cái
Chốt gỗ cứng1 cái
Dải da1 cáiCông cụ cần thiết:
Máy khoan pin
Bộ mũi khoan
Cưa tay6
6
Crank and lid
Crank and lid
Glue the crank arm and a dowel handle on the shaft's outer end, and fit the box's lid, as his rabbeted cover.
Vật liệu cho bước này:
Chốt gỗ cứng1 cái
Keo dán gỗ1 cáiCông cụ cần thiết:
Giấy nhám7
7
The patent drawing
The patent drawing
US 7,490 drawing sheet, public domain (expired patent).

8
8
Churn, then reverse to collect
Churn, then reverse to collect
Let the heavy cream stand until it reaches about 15 °C, checked with the thermometer. Pour in 1.5 litres. Crank steadily; time until the butter comes. Then reverse the crank so the butter collects at the ends of the wings, as they said. Pour off the buttermilk, add cold water, churn a little and pour off again until it runs clear; work in a pinch of salt and weigh the butter.
Vật liệu cho bước này:
Kem tươi béo1500 ml
Muối biển hạt thô1 cái
Nước1 cáiCông cụ cần thiết:
Nhiệt kế đầu dò cắm sẵn
Đồng hồ bấm giờ
Cân nhà bếp điện tử
Tô trộn thép không gỉ (lớn)9
9
Wings that scrape, butter that won't collect
Wings that scrape, butter that won't collect
Quarter-twist spiral dash troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
**Cornelius R. Hight and John Hight** of Geneva, Kane County, Illinois, received US 7,490, dated 9 July 1850. Their wings could be wood or tin, split into the arms with a saw and fastened with brads or small screws; the wing's inner border was cut to arcs of 16- and 23-inch circles; the dash ran on a coupling gudgeon in a cast box and a screw pivot. They wrote it made butter "in from 5 to 8 minutes"; that is their claim, not our measurement. They claimed the application of a reacting spiral revolving dash to a box churn or any of the usual forms of churns.
**Honest limits.** A food-safe box and a printed dash stand in for theirs, and our wings twist evenly rather than following their curved borders. FDM prints hold food in their layer lines, so wash well and replace when worn. Your times and weights are the result.
Vật liệu
8- 1 cáiTạm thời
- Tạm thời
- 1 cáiTạm thời
- 1 cáiTạm thời
- 1 cáiTạm thời
- 1500 mlTạm thời
- 1 cáiTạm thời
- 1 cáiTạm thời
Công cụ yêu cầu
9- Tạm thời
- 1 vendor sell this, none ship to you yetTạm thời
- Tạm thời
- Tạm thời
- Tạm thời
- Tạm thời
- Tạm thời
- Tạm thời
- Tạm thời
Bản thiết kế này làm ra
Blueprint liên quan
Các blueprint này chia sẻ kiến thức — kỹ thuật, vật liệu hoặc nguyên tắc

Spiral-Vane Spring-Agitator Churn: Vanes That Snap Springs on the Bottom
bởi Martin
THỰC PHẨM VÀ ĐỒ UỐNG
27
0
0
0
0
0

Oblique-Wing Reel Churn: Four Wings Across the Line of the Axle
bởi YourGrandma
THỰC PHẨM VÀ ĐỒ UỐNG
12
0
0
0
0
0

Pass-Through Barrel Churn: A Twisted-Wing Dasher That Comes Out Whole Through a Hatch
bởi Woody
Mộc
29
0
0
0
0
0
CC0 Phạm vi công cộng
Bản thiết kế này được phát hành theo CC0. Bạn tự do sao chép, sửa đổi, phân phối và sử dụng cho bất kỳ mục đích nào mà không cần xin phép.
Hỗ trợ nhà sáng tạo bằng cách mua sản phẩm qua bản thiết kế, nơi họ nhận Hoa hồng nhà sáng tạo do nhà bán hàng đặt, hoặc tạo phiên bản mới và kết nối trong bản thiết kế riêng để chia sẻ doanh thu.
