NGHỆ THUẬT
LÀM ĐẸP VÀ SỨC KHỎE
THỦ CÔNG
VĂN HÓA VÀ LỊCH SỬ
GIẢI TRÍ
MÔI TRƯỜNG
THỰC PHẨM VÀ ĐỒ UỐNG
KỸ THUẬT NGƯỢC
KHOA HỌC
THỂ THAO
CÔNG NGHỆ
THIẾT BỊ ĐEO

The Spring-Button Lemon Squeezer: A Button That Gives Way So the Rind Wraps Round It
A flat squeezer presses only the middle of the lemon's cut face, and the rind at its edge keeps its juice.
John Klepzig of San Francisco, California, received US 84,125, dated 17 November 1868, for "forming an opening in one of the squeezing-levers. A movable button, which is operated by a spiral spring, is placed in the opening, and, by placing the fruit between the two levers, and closing them, the juice is expressed, through the hole in the bottom, into the tumbler, while the rind of the lemon is pressed closely against the face of the button-lever, completely enclosing the button." A projection on the other lever pushes the fruit down onto the button.
This rung works out the lever's force and the spring's share, with a work check, then makes the levers in hardwood with a sprung, grooved button and a hollow stem, and squeezes lemons over a tumbler.
Trung cấp
About 4 hours
Hướng dẫn
1
1
Lever and spring
Lever and spring
Đang tải sổ tay Jupyter…
2
2
A hinged squeezer before it
A hinged squeezer before it
The embedded blueprint squeezes the lemon between two cups on crossed handles. Klepzig uses two hinged levers and lets a sprung button give way under the fruit.
3
3
Read US 84,125
Read US 84,125
"A and B are the two levers, connected by a hinge, C. The lever A has a projection, D, so that when the two levers are shut together, the small end of the button E, which sets in the openings in the lever B, is forced out."
"The segregated half of the fruit is placed against the spring-button, and the opposite lever, having the projection, is brought down upon the small end, which presses the rind down upon the smooth surface of the button-lever, completely surrounding the button, and bearing down the spring, which forces out the stem, while the juice of the fruit passes through the centre hole, H, into the tumbler. The face of the button is concave and has grooves centring to the opening."
4
4
Make the levers and squeeze lemons
Make the levers and squeeze lemons
**Levers.** Cut two 25 cm levers from hardwood board, shaped like Klepzig's with handles at one end, and join the other ends with a butt hinge as C.
**Button seat.** Drill a 45 mm stepped hole through lever B, 7 cm from the hinge, narrower at the back to leave a ledge.
**Button.** Turn or rasp a hardwood button that slides in the hole, with a concave face carved with grooves running to a centre hole, and fix a short length of tube through its centre as the stem G, passing through the narrow back of the hole. Put a compression spring round the stem, resting on the ledge.
**Projection.** Glue a rounded hardwood knob to lever A opposite the button as the projection D.
**Test.** Seal the wood with food-safe oil. Hold the squeezer over a tumbler, lay a half lemon cut face down on the button, close the levers and press. Weigh the juice against a half squeezed on a flat board.
Vật liệu cho bước này:
Tấm gỗ cứng1 cái
Khối gỗ cứng2 cái
Bản lề lá1 cái
Vít gỗ6 cái
Ống nhôm0.05 mét
Bộ lò xo nén nhiều cỡ1 cái
Keo dán gỗ1 cái
Chanh vàng2 cáiCông cụ cần thiết:
Cưa tay
Máy khoan pin
Bộ mũi khoan
Bộ đục gỗ
Giũa thô
Giấy nhám
Bộ tua vít
Dao bếp
Cân nhà bếp điện tử
Cốc uống nước5
5
A button that sticks, leaks or does not wrap the rind
A button that sticks, leaks or does not wrap the rind
Spring-button lemon squeezer troubleshooting.
Flow
Loading...
6
6
History and honest limits
History and honest limits
**John Klepzig** of San Francisco, California, received US 84,125, dated 17 November 1868. The opening in lever B was smaller at the back than at the face, leaving a ledge on which the spiral spring F rested, and the small end or tube G attached to the button passed through the lesser hole. His claim is the movable button with its opening and spiral spring, with the two levers.
**Honest limits.** Hardwood levers, a carved button and a bought spring stand in for his made-up parts. The notebook ignores friction; its forces, lengths and spring are examples. Your juice weights are the result.
Vật liệu
8- 1 cáiTạm thời
- 2 cáiTạm thời
- 1 cáiTạm thời
- 6 cáiTạm thời
- 0.05 métTạm thời
- Tạm thời
- 1 cáiTạm thời
- 2 cáiTạm thời
Bản thiết kế này làm ra
Blueprint liên quan
Các blueprint này chia sẻ kiến thức — kỹ thuật, vật liệu hoặc nguyên tắc

The Porcelain-Lined Lemon Squeezer: Cast-Iron Handles, Porcelain Where the Juice Runs
bởi Mary
Đồ gốm
36
0
0
0
0
0

The Shears-Cup Lemon Squeezer: Two Cups on Crossed Handles, a Slotted Recess for the Juice
bởi TheChef
Gia công kim loại
33
0
0
0
0
0

The Law of the Lever — Archimedes' Balance of Weight and Distance
bởi Martin
Vật lý học
60
0
0
0
1
0
CC0 Phạm vi công cộng
Bản thiết kế này được phát hành theo CC0. Bạn tự do sao chép, sửa đổi, phân phối và sử dụng cho bất kỳ mục đích nào mà không cần xin phép.
Hỗ trợ nhà sáng tạo bằng cách mua sản phẩm qua bản thiết kế, nơi họ nhận Hoa hồng nhà sáng tạo do nhà bán hàng đặt, hoặc tạo phiên bản mới và kết nối trong bản thiết kế riêng để chia sẻ doanh thu.
