Ukusebenzisana
UBUCIKO
UBUHLE NEMPILO
UBUCIKO BEZANDLA
AMASIKO NOMLANDO
EZOKUZIJABULISA
IMVELO
UKUDLA NEZIPHUZO
REVERSE ENGINEERING
IZAYENSI
EZEMIDLALO
UBUCHWEPHESHE
IZINTO EZIGQOKWAYO
Magnetic-Field Press: Soft-Steel Punches as the Poles (Cochardt, US 3,412,461, 1968)
A press that lines magnetic powder up while it squeezes it. Two punches of magnetically soft steel close a die, and two coils around them make the punches the poles of an electromagnet. The field runs straight through the powder from one punch face to the other.
Result: a press for anisotropic magnets, about 4000 oersted in the pressing space.
Source: A. W. Cochardt, US 3,412,461 (1968). Unknown: the die's metal, sizes, coil windings, the press and the pump. Picture: the patent drawing.
Osezingeni eliphezulu
Unknown
Imiyalelo
1
1
Make the punches and the die
Make the punches and the die
Make an upper and a lower press member (punches) of magnetically soft steel. Then the magnetic gap is only the thickness of the part being pressed. Make a die wall that the punches close to form a flat cavity. A wide, thin cavity keeps the field lines straight; they bend only at its edges. Ours: mild steel for the punches. Not given: the die's metal, sizes.
Izinto zokwakha zalesi sinyathelo:
Induku eyindilinga yensimbi ethambile1 upper and lower punches
Insimbi engaziwa1 dieAmathuluzi adingekayo:
Umshini Wokuphendula Insimbi
Izilinganiso ezingaziwa2
2
Wind the two coils
Wind the two coils
Wind two coils to sit around the punches, one above the die and one below, so that together they drive a field along the pressing direction. The patent's coils were water-cooled. Ours: enamelled copper wire. Not given: the turns, the wire size, how the cooling water runs.
Izinto zokwakha zalesi sinyathelo:
Ucingo Lwethusi Olumbozwe Nge-Enamel1 two coilsAmathuluzi adingekayo:
AmanziIzilinganiso ezingaziwa3
3
Mount it in a press
Mount it in a press
Mount the punches, die and coils in a press, so the upper punch and the die can move down together while the lower punch stays put. Connect the coils to a current supply. Ours: a hydraulic press and a DC supply. Not given: the press, the supply.
Amathuluzi adingekayo:
Umshini wokucindezela we-hydraulic
Umthombo kagesi we-DC4
4
Press a plate in the field
Press a plate in the field
Raise the lower punch, lower the upper punch into the die, and pump in a ferrite slurry: water with 1 to 2 percent dispersing agent. Move the upper punch and die down to press the slurry and drive out the water, and energise the coils at the same time, to about 4000 oersted. A plate 0.5 x 10 x 9 cm took 8200 watts. Demagnetise the plate as far as possible, then raise the punch, lower the die and lift the plate off the lower punch. Ours: a diaphragm pump.
Amathuluzi adingekayo:
Iphampu ye-diaphragmUmthombo kagesi we-DCAmanziIzinto
3- 1 upper and lower punchesIsibambeli
- 1 dieIsibambeli
- 1 two coilsIsibambeli
Amathuluzi Adingekayo
6- Isibambeli
- Isibambeli
- Isibambeli
- Isibambeli
- Isibambeli
- Isibambeli
Izinto Zokwakha Ze-Blueprint Exhunyiwe
Le blueprint yenza
Ama-blueprint ahlobene
Lama-blueprint abelana ngolwazi — amasu, izinto noma izimiso
CC0 Isizinda Somphakathi
Le blueprint ikhishwe ngaphansi kwe-CC0. Ukhululekile ukukopisha, ukuguqula, ukusabalalisa, nokusebenzisa ngaphandle kwemvume.
Sekela uMenzi ngokuthenga imikhiqizo nge-Blueprint yabo IKhomishane Yomenzi kumiswe ngabathengisi, noma dala inguqulo entsha yale Blueprint bese uyifaka njengoxhumaniso ku-Blueprint yakho ukuze wabelane ngemali engenayo.