Ukusebenzisana
UBUCIKO
UBUHLE NEMPILO
UBUCIKO BEZANDLA
AMASIKO NOMLANDO
EZOKUZIJABULISA
IMVELO
UKUDLA NEZIPHUZO
REVERSE ENGINEERING
IZAYENSI
EZEMIDLALO
UBUCHWEPHESHE
IZINTO EZIGQOKWAYO

Rubber-Pipe Pump Churn: A Pulley Rolls Milk Through a Tube in a Ring and Jets It Through Gauze
Loren J. Wicks of Racine, Wisconsin, received US 24,686, dated 5 July 1859, for a churn that is a rolling-tube pump. An india-rubber pipe runs from the bottom of the milk box once round the groove inside a ring and up into a smaller box on top. A pulley on a fast crank rolls round the ring on the pipe and drives the milk up in a stream against two gauze partitions hung under the top box's cap. The broken milk runs back through a screen of fine wooden strips into the box below, the butter staying behind; the stream keeps going until all the butter is out.
This rung builds it with silicone tubing, a printed ring and pulley, and pine boxes.
Ophakathi
About 1 day, plus printing
Imiyalelo
1
1
A rolling pulley as a pump
A rolling pulley as a pump
Ilayisha incwadi ye-Jupyter…
2
2
A churn that pumps the cream round, before it
A churn that pumps the cream round, before it
McClintock pumped with a vane and valves. Wicks squeezes a rubber pipe and needs no valve at all.
3
3
Read US 24,686
Read US 24,686
"Thus it will plainly be seen that in the manner which pipe (B) passes round circular frame (F) the pulley when rolling on it will force the milk up into box (C)."
4
4
Print the frame F
Print the frame F
The ring with the tube's groove round its inside and the hole in its foot. PETG, 0.2 mm layers, 50 % infill, 5 walls; wash before first use.
5
5
Print the rotor
Print the rotor
The hub with the two projections that carry the pulley. PETG, 0.2 mm layers, 50 % infill, 5 walls; wash before first use.
6
6
Print the pulley H
Print the pulley H
The pulley that rolls on the tube. PETG, 0.2 mm layers, 50 % infill, 5 walls; wash before first use.
7
7
Stand and boxes
Stand and boxes
From pine make box A 360 x 240 mm inside and 230 mm deep, and stand it on four 44 mm legs 400 mm tall. Drill a 13 mm hole near the front of its floor. Make box C 360 x 122 mm inside and 180 mm deep, with a floor, and stand it on two cleats across A's back, leaving A open for 100 mm in front of it. Cut C's front out between 18 and 122 mm up and glue hardwood strips 6 mm wide upright in the opening, 4 mm apart, as screen D. Drill C's front 13 mm above the screen for a 8 mm stainless spout.
Izinto zokwakha zalesi sinyathelo:
Ipulangwe lomphayini3 izicucu
Ukhuni oluthambile lwe-70x70 mm2 izicucu
Iglu Lokhuni1 ucezu
Izikulufu zokhuni40 izicucu
Ipulangwe Lokhuni Oluqinile1 ucezu
Ishubhu lensimbi engagqwali1 ucezuAmathuluzi adingekayo:
Isaha Sesandla
Isaha Le-jigsaw
Ibhola Elingenantambo
Iqoqo Lamakhanda Ebhola
Ama-clamp
Iphepha Lokugaya
Ithephu Lokulinganisa8
8
Cap I and partitions E
Cap I and partitions E
Cut a plywood cap 340 x 100 mm to slide on C's top. Make two frames 240 x 138 mm from 3 mm plywood with a window in each, staple stainless mesh over the windows (for his tin and gauze), and screw them upright under the cap 40 mm apart, across the jet's path.
Izinto zokwakha zalesi sinyathelo:
Ishidi le-plywood1 ucezu
Inetha yocingo1 ucezu
Izikulufu zokhuni8 izicucuAmathuluzi adingekayo:
Isaha Le-jigsaw
Isikeli sensimbi
Isethi yezikulufudrayiva9
9
Frame F, pulley and pipe B
Frame F, pulley and pipe B
Screw a pine board across the front legs below box A and screw the printed frame F on its front, 220 mm up. Bore the board for a 12 mm stainless shaft G with a hardwood support K behind it, fit the rotor and pulley H on its pin inside the frame and a hardwood crank P outside. Push 12 x 8 mm silicone tubing into A's floor hole, sealed, down through a hole in the board and the hole in F's foot, once round the groove, out through the same hole, round the outside of F and up to C's spout.
Izinto zokwakha zalesi sinyathelo:
Ipulangwe lomphayini1 ucezu
Ifilamenti ye-PETG1 ucezu
Insimbi engagqwali eyindukwana2 izicucu
Ipulangwe Lokhuni Oluqinile1 ucezu
Izikhonkwane zokhuni oluqinile1 ucezu
Izikulufu zomshini3 izicucu
Inati Yokukhiya Enenayiloni3 izicucuAmathuluzi adingekayo:
Iphrinta ye-3D yentambo (i-FDM)
Ibhola Elingenantambo
Iqoqo Lamakhanda Ebhola
Isaha Sensimbi
Ummese wemisebenzi
Isethi yezikulufudrayiva10
10
The build in 3D
The build in 3D
FreeCAD model of this build, half the boxes cut away: box A on its stand, box C with screen D, the cap and the two mesh partitions, the board with frame F, the rotor and pulley on the shaft, the crank, and the tube's run from A's floor round the ring and up to C. The rotor was checked at six angles.
11
11
Churn
Churn
Pour about 10 litres of cream at about 15 °C into box A, checked with the thermometer. Turn the crank fast and time it: a stream jets into C against the mesh and runs back through the screen. Slide the cap back and forth now and then. When the butter is held in C, stop, lift C off, take the butter out, pour the buttermilk from A, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.
Izinto zokwakha zalesi sinyathelo:
Ukhilimu ojiyile10 l
Usawoti Wolwandle Omkhulu1 ucezu
Amanzi1 ucezuAmathuluzi adingekayo:
Ithemomitha enenaliti eshiywa ngaphakathi
Iwashi Lokumisa Isikhathi
Isikali Sedijithali Sasekhishini
Isitsha esikhulu sokuxuba sensimbi engagqwali12
12
Troubleshooting
Troubleshooting
Rubber-pipe pump troubleshooting.
Flow
Loading...
13
13
History and honest limits
History and honest limits
**Loren J. Wicks** of Racine, Wisconsin, US 24,686, 5 July 1859, "Churn". He did not claim forcing milk in a stream against a substance as such, only boxes A and C with pipe B, and box C with screen D and the hanging partitions E. His pipe was india rubber and his partitions tin and gauze; our silicone tubing, mesh frames, printed ring and pulley and every size are ours.
Izinto
18- 3 izicucuIsibambeli
- 2 izicucuIsibambeli
- 1 ucezuIsibambeli
- 48 izicucuIsibambeli
- 1 ucezuIsibambeli
- 1 ucezuIsibambeli
- 2 izicucuIsibambeli
- 1 ucezuIsibambeli
- 1 ucezuIsibambeli
- 1 ucezuIsibambeli
- 2 izicucuIsibambeli
- Isibambeli
- 3 izicucuIsibambeli
- 3 izicucuIsibambeli
- 1 ucezuIsibambeli
- 10 lIsibambeli
- 1 ucezuIsibambeli
- 1 ucezuIsibambeli
Amathuluzi Adingekayo
16- Isibambeli
- 1 vendor sell this, none ship to you yetIsibambeli
- 1 vendor sell this, none ship to you yetIsibambeli
- Isibambeli
- Isibambeli
- Isibambeli
- 1 vendor sell this, none ship to you yetIsibambeli
- Isibambeli
- Isibambeli
- Isibambeli
- Isibambeli
- Isibambeli
- Isibambeli
- Isibambeli
Amafayela omklamo
4Le blueprint yenza
Ama-blueprint ahlobene
Lama-blueprint abelana ngolwazi — amasu, izinto noma izimiso

Oscillating-Pump Churn: A Half-Round Vane Pump Lifts the Cream Over and Strains It Back Through a Partition
ngu-Martin
Umsebenzi Wokhuni
10
0
0
0
0
0

Funnel-Tube Atmospheric Churn: Trailing Funnels on a Fast Cross Draw Air Down Slanting Tubes Into the Cream
ngu-Buttercup
UKUDLA NEZIPHUZO
4
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
ngu-TheChef
UBUCIKO BEZANDLA
63
0
0
0
0
0
CC0 Isizinda Somphakathi
Le blueprint ikhishwe ngaphansi kwe-CC0. Ukhululekile ukukopisha, ukuguqula, ukusabalalisa, nokusebenzisa ngaphandle kwemvume.
Sekela uMenzi ngokuthenga imikhiqizo nge-Blueprint yabo IKhomishane Yomenzi kumiswe ngabathengisi, noma dala inguqulo entsha yale Blueprint bese uyifaka njengoxhumaniso ku-Blueprint yakho ukuze wabelane ngemali engenayo.

