Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL

Set-Wing Dasher Churn: Wings on Two Cross Rods Through the Staff Are Set by Screws to Lift or Press the Cream
William F. Armstrong and Morgan Payne of Cardington, Ohio, received US 32,814, dated 16 July 1861, for a dasher made of a staff pierced at right angles by two rods, each carrying a wing at either end. Each wing turns on its rod and is fixed by a set screw, so some can be set to lift the cream and others to press it down, and the angles changed at will. Upright strips inside the churn break the swirl.
The patent gives no sizes; every size here is ours.
Iniciante
About 1 day
Instruções
1
1
Setting the wings
Setting the wings
A carregar o notebook Jupyter…
2
2
Paddles sloping opposite ways, five months before
Paddles sloping opposite ways, five months before
Mickey fixes his paddles' slopes. Armstrong and Payne let each wing be set by a screw.
3
3
Read US 32,814
Read US 32,814
"D, D, represent the dashers which are secured to the shafts C, C, by means of set screws as shown so that they may be made permanent in different positions when desired. The cream is elevated by some of the dashers and depressed by others, and the angle at which either occurs may be changed by setting the dashers in different positions."
4
4
Churn A and strips a
Churn A and strips a
Use a 20-litre food-grade bucket as the churn A. Cut four hardwood strips a 20 mm wide and 320 long, tapered behind so their faces stand upright 125 mm from the centre against the sloping wall, and screw them inside from outside a quarter turn apart, 20 mm above the floor, sealing the screw holes. Cut a 12 mm HDPE lid with a 27 mm hole in the middle.
Materiais para este passo:
Balde de 20 litros1 peça
Tábua de madeira de lei1 peça
Parafusos para madeira12 peças
Chapa de PEAD1 peçaFerramentas necessárias:
Serra de mesa
Berbequim sem fios
Jogo de brocas
Conjunto de chaves de fendas
Bússola
Serra tico-tico
Conjunto de brocas de pá5
5
Print the step
Print the step
The step on the floor: 40 mm across, 12 high, with a 12.8 mm hole 8 deep. PETG, 0.2 mm layers, 30 % infill, 4 walls.
6
6
Print the wings D (four)
Print the wings D (four)
A wing: 90 x 60 x 12 mm with a hub 22 mm across, bored 12.4 mm along its length for the rod and 5.2 mm across the hub for an M5 set screw. Print four. PETG, 0.2 mm layers, 30 % infill, 4 walls.
7
7
Staff B, rods C and wings D
Staff B, rods C and wings D
Plane a hardwood staff B 30 mm square and 325 mm long, with a 12 mm stainless pin 10 mm out of its foot, and turn its top 25 mm round for 45 mm above. Bore it 12.2 mm across 100 and 220 mm above its foot, the second at right angles to the first, and push a 12 mm stainless rod C 234 mm long through each. Slide a wing on each rod end and fix it with an M5 set screw: the lower pair turned 30 degrees one way, the upper pair 30 degrees the other. Pin a crank of mild steel flat bar, 108 mm throw, with a hardwood handle on the staff's top.
Materiais para este passo:
Tábua de madeira de lei1 peça
Varão de aço inoxidável2 peças
Filamento PETG1 peça
Parafusos de máquina4 peças
Barra chata de aço macio1 peça
Cavilhas de madeira dura1 peça
Contrapino1 peçaFerramentas necessárias:
Impressora 3D de filamento (FDM)
Serra de mesa
Torno de madeira
Berbequim sem fios
Jogo de brocas
Serra de arco para metais
Limas (lima de mão)
Conjunto de chaves de fendas8
8
The build in 3D
The build in 3D
FreeCAD model of this build, the bucket cut open: four upright strips, the staff on its step with two cross rods and four wings set at opposite angles, the lid and the crank.
9
9
Churn
Churn
Pour about 12 litres of heavy cream at about 15 °C, checked with the thermometer, into the bucket, set the dasher's pin in the step and put on the lid. Turn the crank steadily, timing it. If the cream climbs too high or sits too still, loosen the set screws and change the wings' angles. When the butter comes, lift out the dasher, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.
Materiais para este passo:
Natas para bater12 l
Sal marinho grosso1 peça
Água1 peçaFerramentas necessárias:
Termómetro de sonda permanente
Cronómetro
Balança digital de cozinha
Taça grande de aço inoxidável
Conjunto de chaves de fendas10
10
Troubleshooting
Troubleshooting
Set-wing churn troubleshooting.
Flow
Loading...
11
11
History and honest limits
History and honest limits
**Wm. F. Armstrong** and **Morgan Payne** of Cardington, Morrow County, Ohio, US 32,814, 16 July 1861, "Churn". They claimed "the peculiar arrangement of the dashers or wings upon the shafts C, C". They do not say how the staff is worked; their drawing shows it stepped on a pin in the bottom, so ours is turned by a crank on its top. Their churn widened toward the bottom; ours, a bucket, widens toward the top. The patent gives no sizes; every size here is ours.
Materiais
14- 1 peçaReferência
- 1 peçaReferência
- 12 peçasReferência
- 1 peçaReferência
- 1 peçaReferência
- 2 peçasReferência
- 1 peçaReferência
- 4 peçasReferência
- 1 peçaReferência
- 1 peçaReferência
- 1 peçaReferência
- 12 lReferência
- 1 peçaReferência
- 1 peçaReferência
Ferramentas necessárias
15- 1 vendor sell this, none ship to you yetReferência
- 1 vendor sell this, none ship to you yetReferência
- Referência
- Referência
- Referência
- 1 vendor sell this, none ship to you yetReferência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
Ficheiros de design
3Blueprints relacionados
Estes blueprints compartilham conhecimento — técnicas, materiais ou princípios

Opposed Perforated-Paddle Churn: Sloping Holed Paddles on a Geared Shaft Pass Between Paddles Sloping the Other Way on Slide Bars
por Buttercup
Marcenaria
6
0
0
0
0
0

Notched-Rib Churn: A Solid S-Winged Dasher Turns Inside Upright Ribs Whose Notches Alternate, Crossing the Cream's Currents
por Buttercup
Marcenaria
7
0
0
0
0
0

Spiral-Flange Perforated Dasher Churn: Curved Holed Dashers Fling the Cream Out, a Spiral Flange With Vanes Drives It Back Down
por Buttercup
Marcenaria
10
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
por TheChef
ARTESANATO
63
0
0
0
0
0
CC0 Domínio Público
Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.
Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

