Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Spiral-Flange Perforated Dasher Churn: Curved Holed Dashers Fling the Cream Out, a Spiral Flange With Vanes Drives It Back Down
Buttercup

Criado por

Buttercup

11. novembro 2026IE
10
0
0
0
0

Spiral-Flange Perforated Dasher Churn: Curved Holed Dashers Fling the Cream Out, a Spiral Flange With Vanes Drives It Back Down

John J. Watson of Buffalo, New York, received US 30,438, dated 16 October 1860, for a churn dasher turned by a crank on its staff. Curved main dashers with turned, perforated ends catch the cream as it flies outward, part through their holes and part along the curve back toward the staff, rising; a spiral flange round the staff, with small unperforated vanes, catches that rising cream and throws it back down to the main dashers. The patent gives no sizes; every size here is ours.
Intermediário
About 2 days

Instruções

1

Flinging out, falling back

A carregar o notebook Jupyter…
2

Perforated dashers that break the cream, ten months before

Sprinkle's perforated dasher is driven at a slant. Watson curves and turns the ends of his and adds a spiral flange to send the cream back down.
3

Read US 30,438

"Around the dasher staff is wound a spiral flange, E, upon which are formed auxiliary dashers, a, a. These dashers are not perforated but catch the cream as it approaches the shaft with an upward tendency and throw it back toward the bottom of the churn box or toward the large or main dashers below them."
4

Box A and lid

Use a 20-litre food-grade bucket as the box A. Cut a 12 mm HDPE lid to its top, 304 mm across, bored 16.6 mm at the centre as the staff's top bearing.

Materiais para este passo:

Balde de 20 litrosBalde de 20 litros1 peça
Chapa de PEADChapa de PEAD1 peça

Ferramentas necessárias:

BússolaBússola
Serra tico-ticoSerra tico-tico
Conjunto de brocas de páConjunto de brocas de pá
Berbequim sem fiosBerbequim sem fios
5

Print the step

The step on the bucket's floor: 60 mm across, 10 high, with a 10.6 mm hole 9 deep. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Arquivo de designSTLCC0 - Free
6

Print the main dashers D (six)

One main dasher D: a blade 60 mm high and 4 thick, straight from the hub then curved forward over its outer 40 mm to 120 mm from the staff's centre, with 8 mm holes in two rows along the curve, on an 18 mm hub with a 10.4 mm bore and a split-pin hole. Print six. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Arquivo de designSTLCC0 - Free
7

Print the spiral flange sections E (two)

One section of the spiral flange E: a third of a turn of 120 mm pitch, reaching from a 38 mm sleeve (32.4 mm bore, 40 high) to 55 mm out, 4 thick, with three vanes a 10 mm high leaning 30 degrees. Print two, with supports. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Arquivo de designSTLCC0 - Free
8

Staff B, flange E and dashers D

Turn a hardwood staff B 32 mm across and 315 mm long. Set a 10 mm stainless pin 10 mm out of its foot and a 16 mm stainless rod 133 mm long 20 mm into its top. Slide the two flange sections on, one 80 to 120 mm above the foot and one 190 to 230 mm, the upper turned a quarter turn on from the lower, and fix each with a screw through its sleeve. Bore the staff 10.2 mm across at 45, 155 and 265 mm above its foot, each a quarter turn from the last, and push a 10 mm stainless rod 120 mm long through each. Slide a dasher D on each end, curves leading the same way round, and fix it with a split pin. Pin a crank of mild steel flat bar, 108 mm throw, with a hardwood handle on the stainless top.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei1 peça
Varão de aço inoxidávelVarão de aço inoxidável3 peças
Filamento PETGFilamento PETG1 peça
Parafusos para madeiraParafusos para madeira2 peças
ContrapinoContrapino6 peças
Barra chata de aço macioBarra chata de aço macio1 peça
Cavilhas de madeira duraCavilhas de madeira dura1 peça

Ferramentas necessárias:

Impressora 3D de filamento (FDM)Impressora 3D de filamento (FDM)
Torno de madeiraTorno de madeira
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Serra de arco para metaisSerra de arco para metais
Limas (lima de mão)Limas (lima de mão)
Torno de bancadaTorno de bancada
Conjunto de chaves de fendasConjunto de chaves de fendas
Fita métricaFita métrica
9

The build in 3D

FreeCAD model of this build, the bucket cut open: the step, the staff with its three pairs of curved, holed dashers on cross-rods, the two spiral flange sections with their vanes between the levels, the lid and the crank.
Arquivo de designBLENDCC0 - Free
10

Churn

Set the step on the bucket's floor, stand the dasher in it, pour in about 12 litres of heavy cream at about 15 °C, checked with the thermometer, and put on the lid over the staff's top. Turn the crank steadily, the dashers' curved ends leading, timing it. When the butter comes, lift the lid and dasher out, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

Materiais para este passo:

Natas para baterNatas para bater12 l
Sal marinho grossoSal marinho grosso1 peça
ÁguaÁgua1 peça

Ferramentas necessárias:

Termómetro de sonda permanenteTermómetro de sonda permanente
CronómetroCronómetro
Balança digital de cozinhaBalança digital de cozinha
Taça grande de aço inoxidávelTaça grande de aço inoxidável
11

Troubleshooting

Spiral-flange churn troubleshooting.

Flow

Loading...
12

History and honest limits

**John J. Watson** of Buffalo, Erie County, New York, US 30,438, 16 October 1860, "Churn-Dasher". He claimed "the arrangement of the main dashers, D, D, with the auxiliary dashers, a a and the spiral flange E". He gives the dashers' form only as drawn, and does not say how many there are or how far round the flange runs; Fig. 1 draws one twisted band up the staff's height, while ours is two short sections between the dashers' levels. His dashers were metal; ours are printed. Every size here is ours.

Materiais

12

Ferramentas necessárias

16

Ficheiros de design

4

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...