Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Notched-Rib Churn: A Solid S-Winged Dasher Turns Inside Upright Ribs Whose Notches Alternate, Crossing the Cream's Currents
Buttercup

Criado por

Buttercup

11. novembro 2026IE
7
0
0
0
0

Notched-Rib Churn: A Solid S-Winged Dasher Turns Inside Upright Ribs Whose Notches Alternate, Crossing the Cream's Currents

V. Stirewatt of Albany, Georgia, received US 31,413, dated 12 February 1861, for a churn lined with upright ribs. Each rib is notched, and the notches of neighbouring ribs alternate, so the cream swirled by the dasher is stopped and let through by turns, crossing and mixing with air. The dasher is one solid piece with two curved wings that nearly fill the body; turned one way it throws the cream out, the other way it gathers the butter. A crank and gears on a cross piece pinned to two ears drive it, and lift off as one. The patent gives no sizes; every size here is ours.
Intermediário
About 2 days

Instruções

1

Notches that cross the currents

A carregar o notebook Jupyter…
2

Fixed brakes that break the current, two years before

Taylor's slotted brakes break the current round a dasher. Stirewatt's ribs alternate their notches so the currents cross.
3

Read US 31,413

"The action of these alternately placed spaces and rib projections is such that the cream is forced, in intermingling and crossing currents, around the inside of the churn body, thereby greatly increasing its agitation and intermingling more air therewith."
4

Body A and ribs L

Use a 20-litre food-grade bucket as the body A. Cut eight hardwood ribs 20 mm wide and 300 long, tapered so their inner faces stand upright 117 mm from the centre against the bucket's sloping wall (about 20 mm deep at the foot, 30 at the top). Cut five notches m 30 mm long and 12 deep in each, on 60 mm centres, starting 15 mm from the foot on four of them and 45 mm on the other four, whose last notch runs out at the top. Screw them inside from outside (screws l), 20 mm above the floor and an eighth of a turn apart, the two patterns alternating, and seal the screw holes.

Materiais para este passo:

Balde de 20 litrosBalde de 20 litros1 peça
Tábua de madeira de leiTábua de madeira de lei1 peça
Parafusos para madeiraParafusos para madeira24 peças
Vedante de siliconeVedante de silicone1 peça

Ferramentas necessárias:

Serra de mesaSerra de mesa
Conjunto de formões para madeiraConjunto de formões para madeira
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Conjunto de chaves de fendasConjunto de chaves de fendas
Fita métricaFita métrica
5

Print the bearing i

The bearing on the bucket's floor: 50 mm across, 12 high, with a 16.8 mm hole 8 deep. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Arquivo de designSTLCC0 - Free
6

Dasher H and shaft f

Glue up hardwood into a block 260 mm tall and cut it to the plan of Fig. 2: a round hub 56 mm across with two wings curving the same way round, 30 mm thick at the hub tapering to 12 at the tips, reaching 108 mm from the centre. Bore it 16.2 mm through the centre and pin it on a 16 mm stainless shaft f 325 mm long, its foot 5 mm below and the dasher 20 mm above the floor. File the shaft's top 15 mm square, 11 mm across the flats.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei2 peças
Cola de madeiraCola de madeira1 peça
Varão de aço inoxidávelVarão de aço inoxidável1 peça
Cavilhas de madeira duraCavilhas de madeira dura1 peça

Ferramentas necessárias:

Serra de mesaSerra de mesa
Serra tico-ticoSerra tico-tico
Conjunto de formões para madeiraConjunto de formões para madeira
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Serra de arco para metaisSerra de arco para metais
Limas (lima de mão)Limas (lima de mão)
Torno de bancadaTorno de bancada
Sargento de barraSargento de barra
7

Print the socket g

The socket on the pinion shaft's lower end: 32 mm across, 30 long, an 11.4 mm square hole 15 deep below and a 16.2 mm round bore above. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Arquivo de designSTLCC0 - Free
8

Print the pinion E

The pinion E on the shaft d: 14 teeth, module 2.5, 16.2 mm bore. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Arquivo de designSTLCC0 - Free
9

Print the driving wheel D

The driving wheel D on the crank shaft: a crown wheel of 42 teeth, module 2.5, 16.2 mm bore. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Arquivo de designSTLCC0 - Free
10

Cover I, ears a, cross piece B, standard C, gears and crank G

Cut a 12 mm HDPE cover I to the bucket's top with a 26 mm hole in the middle. Screw two hardwood ears a 30 x 40 mm, 105 long, to opposite sides of the bucket's top, standing 45 mm above its rim. Cut a hardwood cross piece B 370 x 140 x 25 mm, notched at its ends to drop over the ears, bored 8.4 mm across through ears and ends for stainless pins b, and bored 16.6 mm at the centre. Screw two hardwood bearing blocks C 50 x 25 x 108 mm on B, one 60 to 85 mm in front of the centre and one 25 to 50 behind, bored 16.6 mm across 83 mm up. Run a 16 mm stainless shaft d 125 mm long down through B and the cover with the socket g pinned on its foot and the pinion E pinned on its top, its teeth 30 mm above B. Run a 16 mm stainless crank shaft 180 mm long through the blocks with the wheel D pinned on meshing E, a shaft collar, and a crank G of mild steel flat bar, 100 mm throw, with a hardwood handle.

Materiais para este passo:

Chapa de PEADChapa de PEAD1 peça
Tábua de madeira de leiTábua de madeira de lei1 peça
Parafusos para madeiraParafusos para madeira12 peças
Varão de aço inoxidávelVarão de aço inoxidável3 peças
Shaft CollarShaft Collar1 peça
ContrapinoContrapino4 peças
Barra chata de aço macioBarra chata de aço macio1 peça
Cavilhas de madeira duraCavilhas de madeira dura1 peça
Filamento PETGFilamento PETG1 peça

Ferramentas necessárias:

Impressora 3D de filamento (FDM)Impressora 3D de filamento (FDM)
BússolaBússola
Serra tico-ticoSerra tico-tico
Conjunto de brocas de páConjunto de brocas de pá
Serra de mesaSerra de mesa
Conjunto de formões para madeiraConjunto de formões para madeira
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Serra de arco para metaisSerra de arco para metais
Limas (lima de mão)Limas (lima de mão)
Torno de bancadaTorno de bancada
Conjunto de chaves de fendasConjunto de chaves de fendas
11

The build in 3D

FreeCAD model of this build, the bucket cut open: the eight notched ribs, the S-winged dasher on its shaft and bearing, the socket and pinion shaft, the cover, the ears and pinned cross piece with its bearing blocks, the gears and the crank.
Arquivo de designBLENDCC0 - Free
12

Churn and gather

Pour about 10 litres of heavy cream at about 15 °C, checked with the thermometer, into the bucket with the dasher in, put on the cover, drop the cross piece over the ears so the socket takes the shaft's square, and push in the pins. Turn the crank so the wings' convex faces lead, timing it. When the butter comes, turn the other way a while to gather it. Pull the pins, lift off the gearing and cover, lift out the dasher, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

Materiais para este passo:

Natas para baterNatas para bater10 l
Sal marinho grossoSal marinho grosso1 peça
ÁguaÁgua1 peça

Ferramentas necessárias:

Termómetro de sonda permanenteTermómetro de sonda permanente
CronómetroCronómetro
Balança digital de cozinhaBalança digital de cozinha
Taça grande de aço inoxidávelTaça grande de aço inoxidável
13

Troubleshooting

Notched-rib churn troubleshooting.

Flow

Loading...
14

History and honest limits

**V. Stirewatt** of Albany, Dougherty County, Georgia, US 31,413, 12 February 1861, "Churn"; the printed text spells the name Stirewatt and the drawing Stirewalt. He claimed "the ribs, or cleats, L, L, on the inner surface of the churn body A, arranged and operating in combination with the dasher H". He allowed the notches to run the full depth of the ribs or only part of it; ours are part depth, so each rib stays in one piece. He gives the dasher's form only as Fig. 2 and does not say which way to turn for churning; we lead with the wings' convex faces. His gears were bevel wheels on an iron standard; ours are a printed crown wheel and pinion on wooden blocks. Every size here is ours.

Materiais

15

Ferramentas necessárias

18

Ficheiros de design

5

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...