Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Blake Jaw Breaker: Eccentric, Pitman and Two Toggles Swing a Steel Jaw Against a Fixed Chilled Plate (Richards, Ore Dressing, 1903)
Forge

Criado por

Forge

15. novembro 2026NO
4
0
0
0
0

Blake Jaw Breaker: Eccentric, Pitman and Two Toggles Swing a Steel Jaw Against a Fixed Chilled Plate (Richards, Ore Dressing, 1903)

Eli Whitney Blake's jaw breaker (patented 1858), the standard first crusher of the ore mill, as Robert Richards described it: a ribbed cast frame on four legs, a fixed jaw bedded in zinc, a steel swing jaw hung from a shaft at the top, and an eccentric that lifts a pitman to straighten two toggles and push the jaw shut; rubber springs pull it back. A wedge sets the gap; a heavy flywheel carries it through each half-turn of crushing.
Avançado
Weeks (castings and machining)

Instruções

1

Sizes and power

A carregar o notebook Jupyter…
2

Read Richards

"As the eccentric lifts the pitman, it straightens out the toggles, lengthening the distance between their outer ends. This forces the swing jaw to approach the fixed jaw, crushing the rock."
3

Frame and fixed jaw

Cast the frame of strong, ribbed cast iron or cast steel, with four legs bolted down, bearing boxes on top for the swing-jaw shaft and the eccentric shaft, and a horizontal web at the rear for the toggle block and wedge. Bed the fixed jaw against the frame end with 1/4 in. (6 mm) of zinc, and hold its jaw plate with two wedge-shaped cheek plates driven into recesses in the frame.

Materiais para este passo:

Peças fundidas de ferroPeças fundidas de ferro1 peça
Lingote de zincoLingote de zinco1 peça
Sortido de parafusos sextavadosSortido de parafusos sextavados1 peça

Ferramentas necessárias:

Colher de fundiçãoColher de fundição
Talha de roldanasTalha de roldanas
MarteloMartelo
4

Swing jaw

Make the swing jaw of steel, fixed to its shaft by a gib and key bolt, with its jaw plate held by dovetails, a steel toggle bearing at the back and an eye near the bottom for the spring rod. Jaw plates: chilled cast iron with lengthwise 90° corrugations.

Materiais para este passo:

Peças fundidas de ferroPeças fundidas de ferro1 peça
Veio de açoVeio de aço1 peça

Ferramentas necessárias:

Torno mecânicoTorno mecânico
Conjunto de chaves de bocaConjunto de chaves de boca
5

Pitman, toggles and wedge

Hang a strong steel pitman from the eccentric shaft on babbitt bearings taken up by a key. Fit two toggles: one between the toggle block and the pitman, one between the pitman and the swing jaw, all four toggle bearings steel, held by set screws. Set the toggle block on its bolt against the wedge, which an adjusting bolt raises or lowers.

Materiais para este passo:

Veio de açoVeio de aço1 peça
Metal desconhecidoMetal desconhecido1 peça
Peças fundidas de ferroPeças fundidas de ferro1 peça

Ferramentas necessárias:

Torno mecânicoTorno mecânico
Conjunto de chaves de bocaConjunto de chaves de boca
6

Springs, flywheel and drive

Fit two spring rods from the swing jaw through rubber springs held in compression against a spring bar. Key a heavy flywheel to the eccentric shaft and bolt the drive pulley to it; plug all oil holes against grit and shield the boxes and toggles with the half hopper. Drive it by belt (Table 5: 275 rev./min).

Materiais para este passo:

Placa de borracha naturalPlaca de borracha natural1 peça
Peças fundidas de ferroPeças fundidas de ferro1 peça
RoldanaRoldana1 peça
Correia de transmissãoCorreia de transmissão1 peça
Sortido de parafusos sextavadosSortido de parafusos sextavados1 peça

Ferramentas necessárias:

Conjunto de chaves de bocaConjunto de chaves de boca
Torno mecânicoTorno mecânico
7

Run and adjust

Feed rock by hand, shovel or chute into the mouth. As the jaw plates wear and the product gets coarse, raise the wedge by its nut; when that is used up, fit longer toggles that keep the pitman vertical; then turn the jaw plates end for end; last, fit new plates.

Ferramentas necessárias:

Conjunto de chaves de bocaConjunto de chaves de boca
8

Troubleshooting

Jaw breaker troubleshooting.

Flow

Loading...
9

History and honest limits

From Robert H. Richards, *Ore Dressing* vol. I (1903), Chapter II, §§ 11-14, pp. 13-17, Figs. 5-8 and Table 5 (checked on the archive.org scan oredressing01richuoft; p. 15 from its text layer). Blake's first 1858 form gave the most movement at the mouth; he soon reversed it so the bottom of the jaw moves most. Richards describes a bought Farrel or Fraser & Chalmers machine: building it from castings and metric figures are ours, and the babbitt alloy has no head yet.

Materiais

8

Ferramentas necessárias

5

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...