Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Monorail Sled: Two Tandem Plank Runners Shod With Strap Iron, Steered Lying Down (Boy Mechanic, 1915)
Woody

Criado por

Woody

13. novembro 2026NO
4
0
0
0
0

Monorail Sled: Two Tandem Plank Runners Shod With Strap Iron, Steered Lying Down (Boy Mechanic, 1915)

Harry Hardy's monorail sled from The Boy Mechanic, Book 2 (1915): two plank runners one behind the other under a 6 ft board, shod with square-edged strap iron that grips like a skate. The rider lies full length and steers the front runner with a bar, balancing like a cyclist.
Intermediário
About 1 day

Instruções

1

His sketch in centimetres

A carregar o notebook Jupyter…
2

Read The Boy Mechanic, Book 2

"Round iron or half-round iron should not be used, as these are liable to skid. The square, sharp edges of the strap iron prevent this and grip the surface just as a skate."
3

Cut and shoe the runners

Cut the two runners from 1 in plank to the size and shape of his sketch: the front runner 2 ft long, the rear one 2-1/2 ft long and about 1 ft high (the sketch prints the rear length with an inch mark; it is drawn as 2-1/2 ft). Shoe them with strap iron 1 in wide and 1/4 in thick, keeping the edges square and sharp.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei1 peça
Barra chata de aço macioBarra chata de aço macio1 peça
Parafusos para madeiraParafusos para madeira1 peça

Ferramentas necessárias:

SerroteSerrote
Serra de recortesSerra de recortes
Serra de arco para metaisSerra de arco para metais
Torno de bancadaTorno de bancada
Berbequim de mãoBerbequim de mão
LápisLápis
Fita métricaFita métrica
4

Fit the rear runner

Nail or bolt blocks on either side of the upper edge of the rear runner and screw the top board (6 ft long, 1 in thick) to them. Brace the runner with strap iron, as in the sketch.

Materiais para este passo:

Tábua de pinhoTábua de pinho1 peça
Tábua de madeira de leiTábua de madeira de lei1 peça
Barra chata de aço macioBarra chata de aço macio1 peça
Parafuso de carroçariaParafuso de carroçaria1 peça
Parafusos para madeiraParafusos para madeira1 peça

Ferramentas necessárias:

SerroteSerrote
Serra de arco para metaisSerra de arco para metais
Berbequim de mãoBerbequim de mão
MarteloMartelo
5

Fit the front runner and steering

Fit the front runner the same way, but with only one pair of blocks at the centre and a thin piece of wood on their tops as the fifth wheel. Bore the hole for the steering post 6 in from the front end of the top, a little larger than the post. Round the post where it passes through the hole and leave its upper end square, to take the steering bar tightly.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei1 peça
Barra chata de aço macioBarra chata de aço macio1 peça
Parafusos para madeiraParafusos para madeira1 peça

Ferramentas necessárias:

SerroteSerrote
Arco de pua e brocaArco de pua e broca
FormõesFormões
Plaina manualPlaina manual
6

Troubleshooting

Monorail sled troubleshooting.

Flow

Loading...
7

History and honest limits

From "How to Make a Monorail Sled" by Harry Hardy, in **The Boy Mechanic, Book 2**, Popular Mechanics, 1915 (Project Gutenberg 44585; checked on the archive.org scan boymechanicbook200chic2, p. 50). The rear runner length is printed 2-1/2 with an inch mark but drawn longer than the 2 ft front runner, so it is read here as 2-1/2 ft. He gives no sizes for the blocks, braces or steering bar. The tools and metric figures are ours.

Materiais

5

Ferramentas necessárias

11

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...