Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Spatter-Guard Spring Dasher Churn: A Funnel-and-Bowl Block on the Lid Keeps the Cream In, a Spring Lifts the Dasher
Buttercup

Criado por

Buttercup

11. novembro 2026IE
4
0
0
0
0

Spatter-Guard Spring Dasher Churn: A Funnel-and-Bowl Block on the Lid Keeps the Cream In, a Spring Lifts the Dasher

John M. Buell of Zanesville, Ohio, received US 29,460, dated 7 August 1860, for an add-on to the common dasher churn. A block on the lid has a bowl underneath that catches the spatters and a funnel on top that takes back the cream wiped off the handle. A spiral spring from the block to a head block clamped on the handle lifts the dasher again after every push, so churning is only pushing down. The patent gives no sizes; every size here is ours.
Iniciante
About 1 day

Instruções

1

Choosing the spring B

A carregar o notebook Jupyter…
2

A spring that lifts the dasher, a month before

Cooper lifts the dasher with rubber springs on a lever frame. Buell puts one coil spring straight round the handle.
3

Read US 29,460

"Press down g; C being attached will be carried down by it, thus compressing B. When down B will immediately expand and raise g to the same point again and so it will continue to operate making the labor of churning to consist merely in pushing down the dasher."
4

Churn, lid F and dasher

Use a 20-litre food-grade bucket as the common churn. Cut a 12 mm HDPE lid F 304 mm across with a 30 mm hole in the middle. Cut two hardwood boards 220 x 40 x 16 mm, cross them, and screw them to the foot of a 25 mm hardwood handle g 1000 mm long.

Materiais para este passo:

Balde de 20 litrosBalde de 20 litros1 peça
Chapa de PEADChapa de PEAD1 peça
Tábua de madeira de leiTábua de madeira de lei1 peça
Cavilhas de madeira duraCavilhas de madeira dura1 peça
Cola de madeiraCola de madeira1 peça
Parafusos para madeiraParafusos para madeira4 peças

Ferramentas necessárias:

Serra de mesaSerra de mesa
Serra tico-ticoSerra tico-tico
Conjunto de brocas de páConjunto de brocas de pá
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Conjunto de chaves de fendasConjunto de chaves de fendas
5

Device A: bowl d and funnel E

Glue up hardwood and turn a block A 90 mm across and 90 mm tall. Bore it 27 mm through the middle, so the handle is wiped as it rises. Turn the top into a funnel E, 60 mm across at the top narrowing to the bore 40 mm down, and hollow the underside into a half-round bowl d 70 mm across.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei1 peça
Cola de madeiraCola de madeira1 peça

Ferramentas necessárias:

Torno de madeiraTorno de madeira
Conjunto de goivas de entalheConjunto de goivas de entalhe
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Fita métricaFita métrica
6

Spring B, head block C and thumb screw s

Get a compression spring about 73 mm outside, 280 mm long free and about 0.15 N per mm (16 turns of 3 mm wire). Turn a hardwood head block C 90 mm across and 30 thick, bored 26 mm. Bore its side 8.5 mm to the bore, let an M8 hex nut into the hole's mouth with glue, and run in an M8 threaded rod 50 mm long with a wing nut locked by a hex nut on its outer end: the thumb screw s. Fix one end of the spring to the rim of A's top and the other under C, each under a screw and washer, so A, B and C lift off as one.

Materiais para este passo:

Conjunto de molas de compressãoConjunto de molas de compressão1 peça
Tábua de madeira de leiTábua de madeira de lei1 peça
Varão roscadoVarão roscado1 peça
Porca sextavadaPorca sextavada2 peças
Porca borboletaPorca borboleta1 peça
Anilha planaAnilha plana2 peças
Parafusos para madeiraParafusos para madeira2 peças
Cola de madeiraCola de madeira1 peça

Ferramentas necessárias:

Torno de madeiraTorno de madeira
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Serra de arco para metaisSerra de arco para metais
Limas (lima de mão)Limas (lima de mão)
Chave inglesa ajustávelChave inglesa ajustável
Conjunto de chaves de fendasConjunto de chaves de fendas
7

The build in 3D

FreeCAD model of this build, the bucket and block A cut open: the dasher and handle, the lid, block A with its bowl underneath and funnel on top, the spring, and the head block with its thumb screw.
Arquivo de designBLENDCC0 - Free
8

Set the stroke and churn

Pour about 10 litres of heavy cream at about 15 °C, checked with the thermometer, into the churn, stand the dasher in, and put on the lid. Slide A, B and C down the handle until A rests on the lid. Raise the handle to the top of its stroke, about 150 mm above where the dasher meets the bottom, and turn the thumb screw tight. Push the handle down and let the spring lift it, steadily, timing it. When the butter comes, loosen the thumb screw and lift A, B and C off the handle, take out the dasher and butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

Materiais para este passo:

Natas para baterNatas para bater10 l
Sal marinho grossoSal marinho grosso1 peça
ÁguaÁgua1 peça

Ferramentas necessárias:

Termómetro de sonda permanenteTermómetro de sonda permanente
CronómetroCronómetro
Balança digital de cozinhaBalança digital de cozinha
Taça grande de aço inoxidávelTaça grande de aço inoxidável
9

Troubleshooting

Spring dasher churn troubleshooting.

Flow

Loading...
10

History and honest limits

**John M. Buell** of Zanesville, Muskingum County, Ohio, US 29,460, 7 August 1860, "Churn". He claimed "the device A constructed as described, in combination with the churn, spring B, handle g, and head block C". His churn was the common staved dasher churn with its own lid; ours is a bucket. The patent gives no sizes; every size here is ours.

Materiais

14

Ferramentas necessárias

16

Ficheiros de design

1

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...