Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Spring-Lever Dasher Churn: A Hand Lever and a Faster Bar on a Post Drive the Old Dasher Down, a Rubber Spring Lifts It
Buttercup

Criado por

Buttercup

11. novembro 2026IE
6
0
0
0
0

Spring-Lever Dasher Churn: A Hand Lever and a Faster Bar on a Post Drive the Old Dasher Down, a Rubber Spring Lifts It

N. B. Cooper of Gratis, Ohio, received US 28,970, dated 3 July 1860, for a device to work the old upright dasher churn more easily. A post beside the churn carries a long hand lever and, on an adjustable block, a shorter bar linked to the dasher handle. The two are joined so the bar moves faster than the lever; pressing the lever down drives the dasher into the cream, and an india-rubber spring lifts everything again, like a pump on a spring pole. The block slides to suit churns of any height. The patent gives no sizes; every size here is ours.
Intermediário
About 2 days

Instruções

1

Why the bar d runs ahead of the lever

A carregar o notebook Jupyter…
2

A churn worked against a spring, four months before

Cunningham's spring pole drives the dasher down. Cooper's rubber spring lifts it back up, and the hand drives it down.
3

Read US 28,970

"The labor of lifting and returning the ordinary churn dasher by the smooth vertical handle, is by my process, or that which my improvement introduces, changed to an easy downward pressure upon a nearly horizontal bar or handle, the parts returning upwardly to their place by the force of the spring which was easily overcome by the downward pressure."
4

Base B, churn A, cover C and dasher D

Screw a hardwood base 520 x 400 mm and stand the bucket on it, held by a few cleats round its foot, as the patent says. Cut an HDPE cover with a 28 mm hole in the middle. Make a dasher of two crossed hardwood boards 220 x 40 x 16 mm on a 25 mm hardwood handle long enough to stand 300 mm above the cover.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei2 peças
Balde de 20 litrosBalde de 20 litros1 peça
Chapa de PEADChapa de PEAD1 peça
Cavilhas de madeira duraCavilhas de madeira dura1 peça
Cola de madeiraCola de madeira1 peça
Parafusos para madeiraParafusos para madeira12 peças

Ferramentas necessárias:

Serra de mesaSerra de mesa
Serra tico-ticoSerra tico-tico
Conjunto de brocas de páConjunto de brocas de pá
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Conjunto de chaves de fendasConjunto de chaves de fendas
5

Standard E with slot a and holes b; block c

Glue up a hardwood standard 60 x 40 mm, 800 tall, and frame it into the base behind the churn, 210 mm from its centre. Rout a slot a 18 mm wide through it from 480 to 700 mm up, and bore 10.4 mm holes b across it every 30 mm. Make a hardwood block c that slides in the slot with shoulders bearing on both faces, with a 10 mm stainless pin through a hole b to set its height, and a tail behind the standard for the spring k.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei1 peça
Cola de madeiraCola de madeira1 peça
Varão de aço inoxidávelVarão de aço inoxidável1 peça

Ferramentas necessárias:

Serra de mesaSerra de mesa
TupiaTupia
Conjunto de formões para madeiraConjunto de formões para madeira
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Sargento de barraSargento de barra
6

Lever F, piece g, block i, bar d and links e, f

Cut a hardwood lever F 28 x 16 mm, 810 long, and a piece g 340 long. Pivot both on a 10 mm stainless pin through a hole b 620 mm up, F on one face of the standard and g on the other, 110 mm of each behind it, and join them there with a pin j. At the churn's centre join them with a hardwood block i with a 28 mm upright hole for the dasher handle. Cut a hardwood bar d 24 x 16 mm, pivot it on the block c 55 mm from its back end, and join its back end to the pin j with two mild steel flat bar links f, 71 mm between holes. Join d's front end, 170 mm out, to the dasher handle with a flat bar link e 80 mm long hanging down to a pin m through the handle; bore the hole m where the dasher rests on the bottom with the levers level.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei1 peça
Varão de aço inoxidávelVarão de aço inoxidável1 peça
Barra chata de aço macioBarra chata de aço macio1 peça
Parafuso de carroçariaParafuso de carroçaria4 peças
Porca de segurança com anel de nylonPorca de segurança com anel de nylon4 peças
ContrapinoContrapino4 peças
Cola de madeiraCola de madeira1 peça

Ferramentas necessárias:

Serra de mesaSerra de mesa
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Serra de arco para metaisSerra de arco para metais
Limas (lima de mão)Limas (lima de mão)
Torno de bancadaTorno de bancada
Chave inglesa ajustávelChave inglesa ajustável
7

Springs k and l

Loop a length of elastic cord round the pin j and tie both ends to the block c's tail, tight enough to lift the lever and dasher when let go: the spring k. Tie a shorter loop from the bar d to the lever F as the spring l.

Materiais para este passo:

Cordão elásticoCordão elástico1 peça

Ferramentas necessárias:

Fita métricaFita métrica
8

The build in 3D

FreeCAD model of this build, the churn cut open: the standard with its slot and holes, the block c, the lever F and piece g with the block i round the dasher handle, the bar d with links e and f, the rubber springs, and the dasher.
Arquivo de designBLENDCC0 - Free
9

Churn

Pour about 8 litres of heavy cream at about 15 °C, checked with the thermometer, into the churn and put on the cover. Set the block c so a full press of the handle brings the dasher near the bottom and the spring lifts it clear of the cream. Press the handle down and let it rise, steadily, timing it. When the butter comes, unpin the link e, lift out the dasher, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

Materiais para este passo:

Natas para baterNatas para bater8 l
Sal marinho grossoSal marinho grosso1 peça
ÁguaÁgua1 peça

Ferramentas necessárias:

Termómetro de sonda permanenteTermómetro de sonda permanente
CronómetroCronómetro
Balança digital de cozinhaBalança digital de cozinha
Taça grande de aço inoxidávelTaça grande de aço inoxidável
10

Troubleshooting

Spring-lever churn troubleshooting.

Flow

Loading...
11

History and honest limits

**N. B. Cooper** of Gratis, Preble County, Ohio, US 28,970, 3 July 1860, "Churn". He claimed the mechanism of base, upright, block, hand lever, pivoted bar, links and springs together, to make the old dasher churn lighter work, likening it to a pump on a "spring pole". His springs are india rubber; ours are elastic cord. Every size here is ours.

Materiais

15

Ferramentas necessárias

18

Ficheiros de design

1

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...