Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL

Button-Set Hinged-Slat Dasher Churn: Slats Deflect the Cream, a Button on the Rod Holds Them Open or Lets Them Shut
S. N. Campbell of Elgin, Illinois, received US 25,804, dated 18 October 1859, for a churn. A lever pivoted on a post works a dasher that fits the box closely. Its hinged slats hang open as deflectors: drawn up, the dasher throws the cream down and to the sides; pushed down, it forces the cream up towards a cross piece in the middle. A button with two inclined surfaces on the rod's foot holds the slats open, or, turned half round, lets them shut on the down stroke, to suit the cream.
The patent gives no sizes and does not say where the slats are hinged or how the button bears on them: those and every size here are ours.
Intermediário
About 2 days, plus printing
Instruções
1
1
The button: holding the slats open, or letting them shut
The button: holding the slats open, or letting them shut
A carregar o notebook Jupyter…
2
2
An up-and-down dasher fitting a box closely, three weeks before
An up-and-down dasher fitting a box closely, three weeks before
Austin's middle dasher is a plain plate. Campbell's has hinged slats that deflect the cream, held open or let shut by a button on the rod.
3
3
Read US 25,804
Read US 25,804
"This dasher is constructed with movable slats H, H, which, when open, rest upon stop pins a, and serve the office of deflectors, and as the dasher is drawn up the cream is thrown below the slats and to the sides of the churn and as the dasher is pressed down the cream will be forced up and toward the center of the churn, and against a cross piece J, secured to the center of the dasher."
4
4
Print the button K
Print the button K
A disc 72 mm across and 6 mm thick with two inclined surfaces 60 mm long, one each side, both rising 7.5 mm towards the same end. PETG, 0.2 mm layers, 100 % infill.
5
5
Box A, stand B, post D, lid E and lever C
Box A, stand B, post D, lid E and lever C
From 20 mm hardwood make a box 400 x 300 mm and 380 mm deep inside, on four legs 50 mm square and 300 mm long. Screw a post 50 x 40 mm, 860 mm long, up the middle of the back. Cut a lid with a 32 mm hole in its middle. Bolt a lever 30 x 30 mm, 640 mm long, to the post's top so it reaches over the lid's middle to the front. Fill the box with water overnight so it swells tight, then empty it.
Materiais para este passo:
Tábua de madeira de lei3 peças
Madeira macia de 70x70 mm1 peça
Cola de madeira1 peça
Parafusos para madeira30 peças
Sortido de parafusos sextavados2 peças
Porca de segurança com anel de nylon2 peças
Anilha plana4 peçasFerramentas necessárias:
Serra de mesa
Serrote
Berbequim sem fios
Jogo de brocas
Conjunto de brocas de pá
Sargento de barra
Esquadro fixo
Fita métrica
Água
Chave inglesa ajustável6
6
Dasher G and its slats
Dasher G and its slats
Make two end bars 296 x 40 x 20 mm and join them with the cross piece J, 396 x 40 x 30 mm, bored 31 mm in its middle. Cut two inner slats H 380 x 63 x 12 mm, each with a tab 20 x 9 mm on its inner edge 10 to 30 mm from the middle, and two outer slats H' 380 x 52 x 12 mm. Bore each along its length for a 6 mm stainless hinge pin, H 3 mm in from its inner edge and H' 4 mm in, and hang them between the end bars on pins 392 mm long, H 32 mm and H' 98 mm each side of the middle. Fix 6 mm stop pins, 20 mm long, into the end bars under the slats: 80 mm out and 27 mm below the hinges for H, 130 mm out and 21.5 mm below for H'. Glue posts 20 x 10 x 19 mm on the slats, 120 mm each side of the middle, 40 mm out from each hinge, and join each pair with a piece L 76 x 20 x 6 mm on pins.
Materiais para este passo:
Tábua de madeira de lei2 peças
Varão de aço inoxidável2 peças
Cola de madeira1 peça
Contrapino12 peças
Anilha plana12 peçasFerramentas necessárias:
Serra de mesa
Berbequim sem fios
Jogo de brocas
Serra de arco para metais
Limas (lima de mão)
Lixa
Fita métrica
Sargento de barra7
7
Rod F and button K
Rod F and button K
Turn a hardwood rod F 30 mm across and 440 mm long, with a cross handle at its top to turn it. Pass it down through J and glue the button on its foot, below J, so that in one position its inclined surfaces lie under the slats' tabs and hold the slats open on their pins. Join its top to the lever with a pin in a slot. Set the dasher in the box and the lid on.
Materiais para este passo:
Cavilhas de madeira dura1 peça
Cola de madeira1 peça
Varão de aço inoxidável1 peça
Contrapino2 peças
Filamento PETG1 peçaFerramentas necessárias:
Impressora 3D de filamento (FDM)
Berbequim sem fios
Jogo de brocas
Serra de arco para metais8
8
The build in 3D
The build in 3D
FreeCAD model of this build, one side and one end left off: the box on its stand, the post and lever, the rod, and the dasher with the cross piece J, the hinged slats H and H' on their stop pins, the pieces L and the button K under the tabs. Checked at three heights, with the slats held open and with them shut.
9
9
Churn
Churn
Pour about 20 litres of heavy cream at about 15 °C into the box, checked with the thermometer, and put the lid on. Work the lever up and down, timing it. For thin cream keep the button holding the slats open; if the cream thickens, turn the rod half round so the slats shut on each down stroke. When the butter comes, lift the dasher out, drain the buttermilk, wash the butter in cold water until it runs clear, salt and weigh it.
Materiais para este passo:
Natas para bater20 l
Sal marinho grosso1 peça
Água1 peçaFerramentas necessárias:
Termómetro de sonda permanente
Cronómetro
Balança digital de cozinha
Taça grande de aço inoxidável10
10
Troubleshooting
Troubleshooting
Hinged-slat dasher troubleshooting.
Flow
Loading...
11
11
History and honest limits
History and honest limits
**S. N. Campbell** of Elgin, Kane County, Illinois, US 25,804, 18 October 1859, "Churn". He claimed "the arrangement and combination of the button K, dasher rod F, movable slats H, H', pieces L, and bar J". The patent gives no sizes and does not say where the slats are hinged, how the button's surfaces bear on them, or how the pieces L join H' to H: the hinge lines, the tabs, the button's surfaces, the links and every size here are our reading.
Materiais
14- 3 peçasReferência
- Referência
- 3 peçasReferência
- 30 peçasReferência
- Referência
- Referência
- 16 peçasReferência
- 2 peçasReferência
- 14 peçasReferência
- 1 peçaReferência
- 1 peçaReferência
- 20 lReferência
- 1 peçaReferência
- 1 peçaReferência
Ferramentas necessárias
18- 1 vendor sell this, none ship to you yetReferência
- Referência
- 1 vendor sell this, none ship to you yetReferência
- Referência
- Referência
- Referência
- Referência
- 1 vendor sell this, none ship to you yetReferência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
Ficheiros de design
2Blueprints relacionados
Estes blueprints compartilham conhecimento — técnicas, materiais ou princípios

Three-Crank Churn: One Dasher Strokes Up and Down While Two Side Dashers Swing In and Out
por Buttercup
Marcenaria
9
0
0
0
0
0

Brake-and-Ledge Bar Dasher Churn: Slotted Brakes Break the Current, Ledges Turn It Back to the Dasher
por Buttercup
Marcenaria
10
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
por TheChef
ARTESANATO
63
0
0
0
0
0
CC0 Domínio Público
Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.
Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

