Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Brake-and-Ledge Bar Dasher Churn: Slotted Brakes Break the Current, Ledges Turn It Back to the Dasher
Buttercup

Criado por

Buttercup

11. novembro 2026IE
10
0
0
0
0

Brake-and-Ledge Bar Dasher Churn: Slotted Brakes Break the Current, Ledges Turn It Back to the Dasher

James Taylor of Rushville, Illinois, received US 25,453, dated 13 September 1859, for a churn. An upright dasher of horizontal bars, flattened out towards their ends, turns in a wooden tub and sets the cream turning. Upright brakes inside the tub break the current, and slots in them next to the wall let part of it run on to narrower ledges, which turn it back towards the dasher. The patent gives no sizes; every size here is ours.
Intermediário
About 2 days

Instruções

1

Bars, brakes and how much cream

A carregar o notebook Jupyter…
2

Breakers round a turning dasher, a few weeks before

Sperry's breakers stood on a frame. Taylor fixes his to the tub's wall and slots them next to it.
3

Read US 25,453

"by the action of the dasher the mass of cream or milk in the tub is caused to assume a rotary motion, and the current thus created by coming in contact with the brakes, c, is thrown violently against the sides of the tub and as it passes through the openings, e, in the back part of these brakes and along the sides of the tub, it (the current) strikes against the ledges, d, whereby it is turned in again, toward the dasher"
4

Tub A and cover B

Use a wooden tub 260 mm across inside at the bottom, 230 mm at the top and 420 mm deep, with its top hoop driven up to stand 25 mm above the staves. Glue a hardwood step, 70 mm across and 22 mm thick with a 27 mm hole 16 mm deep, in the middle of the floor. Cut a round cover to drop inside the top hoop, saw it in two across the middle, and bore a 42 mm hole in the middle and a 20 mm air hole 80 mm off it.

Materiais para este passo:

Tina de madeiraTina de madeira1 peça
Tábua de madeira de leiTábua de madeira de lei1 peça
Cola de madeiraCola de madeira1 peça

Ferramentas necessárias:

Serra tico-ticoSerra tico-tico
SerroteSerrote
Berbequim sem fiosBerbequim sem fios
Conjunto de brocas de páConjunto de brocas de pá
Maço de madeiraMaço de madeira
Fita métricaFita métrica
5

Brakes c and ledges d

From 12 mm hardwood cut three brakes 30 mm wide and three ledges 18 mm wide, 345 mm long, their outer edges planed to the staves' slope. In each brake cut a slot 10 mm wide next to its outer edge, stopping 40 mm from each end: the openings e. Screw the brakes upright to the staves through the wall, 15 mm above the floor, one every third of the way round. Screw a ledge 15 degrees after each brake, in the way the dasher turns.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei1 peça
Parafusos para madeiraParafusos para madeira18 peças

Ferramentas necessárias:

Serra de mesaSerra de mesa
Serra tico-ticoSerra tico-tico
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Conjunto de chaves de fendasConjunto de chaves de fendas
LixaLixa
6

Dasher D and its crank

Turn a hardwood shaft C 40 mm across and 503 mm long, its foot turned to 25 mm for 15 mm and its top 24 mm square for 30 mm. Chisel five 25 mm square mortises through it at 45, 110, 175, 240 and 305 mm from the floor, each turned 90 degrees from the last. Cut five bars from 25 x 50 mm hardwood, as long as the tub allows at their height (179, 174, 170, 165 and 160 mm), and shave each from 25 mm square at the middle out to 50 x 8 mm at the ends. Glue them through the shaft. Fit a hardwood crank 190 mm long with a handle on the square top.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei2 peças
Cola de madeiraCola de madeira1 peça
Cavilhas de madeira duraCavilhas de madeira dura1 peça

Ferramentas necessárias:

Torno de madeiraTorno de madeira
Formão de samblagemFormão de samblagem
Maço de madeiraMaço de madeira
Plaina de raspar curvasPlaina de raspar curvas
SerroteSerrote
LixaLixa
Fita métricaFita métrica
7

The build in 3D

FreeCAD model of this build, the tub, hoops and cover cut through the middle: the three brakes with their openings, the three ledges, and the dasher with its five bars and crank. The dasher was turned through 24 angles.
Arquivo de designBLENDCC0 - Free
8

Churn

Stand the dasher's foot in the step and fill the tub with about 15 litres of heavy cream at about 15 °C, checked with the thermometer, up to the upper bar. Put the cover's halves on round the shaft. Turn the crank steadily the way the ledges face, timing it. When the butter comes, lift the cover and dasher, take out the butter, drain the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.

Materiais para este passo:

Natas para baterNatas para bater15 l
Sal marinho grossoSal marinho grosso1 peça
ÁguaÁgua1 peça

Ferramentas necessárias:

Termómetro de sonda permanenteTermómetro de sonda permanente
CronómetroCronómetro
Balança digital de cozinhaBalança digital de cozinha
Taça grande de aço inoxidávelTaça grande de aço inoxidável
9

Troubleshooting

Brake-and-ledge churn troubleshooting.

Flow

Loading...
10

History and honest limits

**James Taylor** of Rushville, Schuyler County, Illinois, US 25,453, 13 September 1859, "Churn". He claimed the arrangement of perforated brakes and auxiliary reflectors with a dasher "having its blades flattened out gradually from near the shaft to their ends", and disclaimed the brakes of Hiram Brown's rejected application of 1852 and of M. R. Marcell's patent of 1858. "The number and size of these brakes and ledges depend entirely upon the size and diameter of the tub": the patent gives no sizes, and every size here is ours, as is the crank.

Materiais

8

Ferramentas necessárias

17

Ficheiros de design

1

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...