Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Digital Kitchen Scale: a Cantilever Load Cell in a Sealed Dual Housing (Edlund, 2009)
Penny

Criado por

Penny

2. novembro 2026DK
13
0
0
0
0

Digital Kitchen Scale: a Cantilever Load Cell in a Sealed Dual Housing (Edlund, 2009)

A digital scale built to survive a kitchen: spills, washing and being dropped. The load cell is a short cantilever with a strain sensor on top, and the electronics sit in a sealed compartment. Both are in a plastic chassis held loosely inside a second, outer housing of stainless steel and plastic, with crushable spacers between the two. Result: a digital kitchen scale with a removable pan, sealed display and touchpad, battery power and an overload stop under the load cell. Source: R. S. Whitney (Edlund Company), US Patent 7,554,043 (2009). Unknown: sizes, capacity, resolution and the electronics; the patent says suitable force transducers are readily available. Ours: the display and button types. Picture: Wikimedia Commons.
Avançado
2 days

Instruções

1

Mount the cantilever load cell

In the load-cell cavity of the plastic chassis, screw a base plate to the cavity floor. Screw the cantilever support to the base plate; a support plate on the cantilever carries the posts for the pan. A strain transducer on top of the cantilever senses the top stretching as it bends under a load. A window in the base plate leaves the cavity floor just below the free end, so an overload bottoms out there instead of breaking the transducer.

Materiais para este passo:

Célula de cargaCélula de carga1 cantilever type
PlásticoPlástico1 chassis
Parafusos de máquinaParafusos de máquina1 conjunto

Ferramentas necessárias:

Conjunto de chaves de fendasConjunto de chaves de fendas
Dimensões desconhecidasDimensões desconhecidas
2

Seal in the electronics

On the other side of the chassis, fit the display electronics behind one opening and the touchpad electronics behind another, wired to the strain transducer through sealing bushings. Fit a battery holder. Close the compartment with its cover on gaskets, so the electronics stay dry. Not given: the circuit, the display and the battery. Ours: a segment LCD and push buttons.

Materiais para este passo:

Circuito integradoCircuito integrado1 weighing and display electronics
Visor LCD de segmentosVisor LCD de segmentos1 peça
Botão de pressãoBotão de pressão1 touchpad keys
BateriaBateria1 peça
Junta de vedaçãoJunta de vedação2 peças
Fio de ligaçãoFio de ligação1 short
Fio de soldaFio de solda1 a little

Ferramentas necessárias:

Ferro de soldarFerro de soldar
Conjunto de chaves de fendasConjunto de chaves de fendas
3

Close it in the outer housing

Place the chassis, unfastened, between the two halves of the outer housing: a stainless-steel top with downturned sides, and a plastic bottom. Spacers moulded on the chassis sides press against the housing sides. They take a blow if the scale is dropped, and may crush on purpose to save the load cell and electronics. A sealed window of plastic or glass shows the display. A flexible sheet covers the touchpad. Fit four height-adjustable feet.

Materiais para este passo:

Chapa de aço inoxidávelChapa de aço inoxidável1 upper housing
PlásticoPlástico1 lower housing
Material desconhecidoMaterial desconhecido1 window, touchpad sheet, four feet

Ferramentas necessárias:

Conjunto de chaves de fendasConjunto de chaves de fendas
Dimensões desconhecidasDimensões desconhecidas
4

Fit the pan and check

Screw the pan support to the four supports of the load cell. Rest the removable pan on it, or snap it on, so it lifts off for washing. A flexible boot can seal each support where it passes through the housing. Ours: check the reading with calibration weights.

Materiais para este passo:

Prato de pesagemPrato de pesagem1 metal or plastic
Parafusos de máquinaParafusos de máquina1 conjunto

Ferramentas necessárias:

Conjunto de chaves de fendasConjunto de chaves de fendas
Conjunto de pesos de calibraçãoConjunto de pesos de calibração

Materiais

13

Ferramentas necessárias

4

Blueprints relacionados

Estes blueprints compartilham conhecimento — técnicas, materiais ou princípios

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...