Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Nested Hollow-Dasher Churn: Two Dasher Frames Turn Contrary Ways, Their Hollowed Side Pieces Driving Cream at Webs
Buttercup

Criado por

Buttercup

11. novembro 2026IE
6
0
0
0
0

Nested Hollow-Dasher Churn: Two Dasher Frames Turn Contrary Ways, Their Hollowed Side Pieces Driving Cream at Webs

Stephen P. Dunham and Austin Hipple of Kilbourne, Ohio, received US 27,894, dated 17 April 1860, for a churn. One dasher frame turns inside another, the two driven contrary ways by one winch through a face-toothed wheel and two pinions. The side pieces of each frame are hollowed on their leading edges and throw the cream at thin webs: the outer frame's at webs on the vessel's wall, the inner frame's at webs on the outer frame. The patent gives no sizes; every size here is ours.
Avançado
About 3 days, plus printing

Instruções

1

One wheel, two pinions, two directions

A carregar o notebook Jupyter…
2

Contrary turning from toothed faces, two months before

Ward turns a cylinder against its dashers. Dunham and Hipple turn one dasher frame inside another.
3

Read US 27,894

"The cream is projected by the surfaces of the hollow s, c, onto the wall of the vessel, by which it is constrained to take up a circular motion till obstructed by the webs, a, and reflected by them in currents, toward the middle of the vessel, and with a velocity increasing as the distances between these hollows and webs diminish."
4

Print the driving wheel D

Face-toothed wheel, 36 teeth, module 2, with a hub; bored 12.4 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Arquivo de designSTLCC0 - Free
5

Print the pinion F

Spur pinion, 16 teeth, module 2, with a hub; bored 18.4 mm for the hollow arbor. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Arquivo de designSTLCC0 - Free
6

Print the pinion E

Spur pinion, 16 teeth, module 2, with a hub; bored 12.4 mm for the shaft S. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Arquivo de designSTLCC0 - Free
7

Webs a, step r and pivot bolt e

Screw four hardwood webs 4 mm thick and 10 deep upright inside the bucket a quarter turn apart, from the floor to 310 mm up, sealing the screw holes outside with silicone. Screw a hardwood block 50 x 50 x 8 mm to the floor's centre as the step r and bore it 12.6 mm, 6 deep. Cut a 12 mm stainless rod 60 mm long as the pivot bolt e.

Materiais para este passo:

Balde de 20 litrosBalde de 20 litros1 peça
Tábua de madeira de leiTábua de madeira de lei1 peça
Bloco de madeira duraBloco de madeira dura1 peça
Parafusos para madeiraParafusos para madeira10 peças
Vedante de siliconeVedante de silicone1 peça
Varão de aço inoxidávelVarão de aço inoxidável1 peça

Ferramentas necessárias:

Serra de mesaSerra de mesa
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Serra de arco para metaisSerra de arco para metais
Limas (lima de mão)Limas (lima de mão)
Conjunto de chaves de fendasConjunto de chaves de fendas
8

Outer dasher with hollows c and webs b

Halve together two hardwood arms 30 x 30 mm, 240 long, for the top and two for the bottom, crossed. Cut four side pieces 20 x 42 mm, 295 long, and join the arms' ends top and bottom with them, 310 mm overall. Hollow each side piece's outer edge on the same side, 12 mm deep at the middle and running out near the ends. Glue a hardwood web b, 4 x 11 mm, along each side piece's inner face. Bore the lower arms' crossing 12.6 mm for the pivot bolt and the upper arms' crossing 33 mm for the journal; fix an 18 mm stainless tube 102 mm long upright over the upper crossing as the hollow arbor.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei2 peças
Cola de madeiraCola de madeira1 peça
Parafusos para madeiraParafusos para madeira16 peças
Tubo de aço inoxidávelTubo de aço inoxidável1 peça

Ferramentas necessárias:

Serra de mesaSerra de mesa
Conjunto de formões para madeiraConjunto de formões para madeira
Serra tico-ticoSerra tico-tico
LixaLixa
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Conjunto de brocas de páConjunto de brocas de pá
Serra de arco para metaisSerra de arco para metais
Sargento de barraSargento de barra
9

Inner dasher with hollows d and journal G

Make the inner dasher the same way from 25 mm hardwood: arms 164 mm long, four side pieces 18 x 34 mm, 195 overall, hollowed 10 mm deep on the opposite edge from the outer dasher's, no webs. Bore the lower arms' crossing 13 mm, 12 deep, for the pivot bolt. Turn a hardwood journal G 32 mm across and 55 tall with two lugs, cut a 12.4 mm square socket in its top, and screw it to the upper arms' crossing.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei1 peça
Bloco de madeira duraBloco de madeira dura1 peça
Cola de madeiraCola de madeira1 peça
Parafusos para madeiraParafusos para madeira12 peças

Ferramentas necessárias:

Serra de mesaSerra de mesa
Conjunto de formões para madeiraConjunto de formões para madeira
Serra tico-ticoSerra tico-tico
LixaLixa
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Sargento de barraSargento de barra
Conjunto de chaves de fendasConjunto de chaves de fendas
10

Cover B, shaft S and gearing

Set the inner dasher inside the outer, its journal up through the outer's upper arms, and stand both on the pivot bolt in the step. Cut a hardwood cover in two halves, 350 x 330 x 15 mm overall, with a 24 mm hole for the arbor; slide pinion F onto the arbor above it. File the bottom 40 mm of a 12 mm stainless shaft square to fit the journal's socket, pass it down through the arbor, and key pinion E on its top. On one half of the cover screw two hardwood standards carrying a 12 mm shaft H with wheel D meshing E above and F below, a hardwood winch I with a dowel handle, and a bracket over E holding the shaft's top.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei2 peças
Varão de aço inoxidávelVarão de aço inoxidável2 peças
Filamento PETGFilamento PETG1 peça
Cavilhas de madeira duraCavilhas de madeira dura1 peça
Cola de madeiraCola de madeira1 peça
Parafusos para madeiraParafusos para madeira12 peças
Shaft CollarShaft Collar2 peças
ContrapinoContrapino1 peça

Ferramentas necessárias:

Impressora 3D de filamento (FDM)Impressora 3D de filamento (FDM)
Serra de mesaSerra de mesa
Serra tico-ticoSerra tico-tico
Conjunto de brocas de páConjunto de brocas de pá
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Serra de arco para metaisSerra de arco para metais
Limas (lima de mão)Limas (lima de mão)
Torno de bancadaTorno de bancada
11

The build in 3D

FreeCAD model of this build, the bucket cut open: the webs a, the outer dasher with hollowed side pieces and webs b, the inner dasher with its hollows and journal, the pivot bolt in its step, and the cover with the wheel D meshing pinion E above and pinion F below.
Arquivo de designBLENDCC0 - Free
12

Churn

Pour about 8 litres of heavy cream at about 15 °C, checked with the thermometer, into the bucket, set the dashers and the gearing in place, and turn the winch steadily, timing it, the way that brings each frame's hollows toward the webs ahead of them. When the butter comes, lift off the cover and gearing, lift out the dashers, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

Materiais para este passo:

Natas para baterNatas para bater8 l
Sal marinho grossoSal marinho grosso1 peça
ÁguaÁgua1 peça

Ferramentas necessárias:

Termómetro de sonda permanenteTermómetro de sonda permanente
CronómetroCronómetro
Balança digital de cozinhaBalança digital de cozinha
Taça grande de aço inoxidávelTaça grande de aço inoxidável
13

Troubleshooting

Nested-dasher churn troubleshooting.

Flow

Loading...
14

History and honest limits

**Stephen P. Dunham** and **Austin Hipple** of Kilbourne, Delaware County, Ohio, US 27,894, 17 April 1860, "Churn". They did not claim a wheel geared with two pinions to turn dashers contrary ways, but the hollowed side pieces working with the webs on the vessel and on the outer dasher. Their vessel is conical, wider at the bottom; ours is a bucket. Every size here is ours, and our gears are printed.

Materiais

15

Ferramentas necessárias

17

Ficheiros de design

4

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...