Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Electromagnet: Horseshoe Holding Magnet Sized by Its Pull (Underhill, 1903)
Volt

Criado por

Volt

3. novembro 2026SE
9
0
0
0
0

Electromagnet: Horseshoe Holding Magnet Sized by Its Pull (Underhill, 1903)

A holding electromagnet in its practical horseshoe form: two iron cores, each wound with wire, fastened to an iron yoke, and an iron armature across the poles. You size it from the pull you need: the pull sets the pole area, and the supply voltage sets the wire. Variable: the pull. Each pound needs a set area of pole, depending on the iron. Source: C. R. Underhill, The Electromagnet (1903), pp. 92, 106-118, 150. Unknown: sizes and the ampere-turns. Picture: Fig. 51 of the book.
Intermediário
Unknown

Instruções

1

Size the poles from the pull

Pull P (pounds) = B² × A / 72,134,000, where B is the flux density in lines per square inch and A the pole area in square inches. Working densities: wrought iron 90,000, cast steel 85,000, Mitis iron 80,000, ordinary cast iron 50,000, which give 112.3, 100.1, 88.72 and 34.66 lb per square inch of pole. Divide the pull you need by that figure to get the pole area. Underhill's example, for cast steel taken at 90,000: 10 lb needs 0.089 square inch, a core 0.336 inch across. A two-pole magnet holds twice the weight of a single pole at the same induction.

Ferramentas necessárias:

Dimensões desconhecidasDimensões desconhecidas
2

Make the cores, yoke and armature

Make the practical horseshoe magnet in three pieces besides the armature: two round cores and a yoke (back iron) to join them. Make an armature to lie across the two pole ends. Face the poles and the armature accurately; an uneven contact spreads the lines unevenly and weakens the pull. Ours: wrought iron. Not given: sizes, how the cores are fastened.

Materiais para este passo:

Barra de ferro forjadoBarra de ferro forjado1 two cores, yoke, armature

Ferramentas necessárias:

Torno mecânicoTorno mecânico
Dimensões desconhecidasDimensões desconhecidas
3

Choose the wire for the supply

Design the coil to stand the full supply voltage without overheating; never put a resistor in series with the magnet, as that wastes power and makes the magnet weaker. Pick the wire size that makes the coil's resistance equal to that of the line and the source, then try the next larger size, and keep the one giving more ampere-turns. A coil rises about 100 °F at about 0.9 watt per square inch of surface for a thin telephone-ringer coil, or 0.33 for a thick one (4 1/8 in across, 7 in long, 1 7/16 in thick), and the rise grows in proportion to the watts. Ours: the supply, e.g. 12 V.

Ferramentas necessárias:

Fonte de alimentação de corrente contínuaFonte de alimentação de corrente contínua
Dimensões desconhecidasDimensões desconhecidas
4

Wind the cores and fasten them to the yoke

Wind the wire directly onto each core between insulating end heads, and fasten the wound cores to the yoke. The joints between cores and yoke lose a little pull. Ours: enamelled copper wire. Not given: the winding method, the insulation.

Materiais para este passo:

Fio de cobre esmaltadoFio de cobre esmaltado1 two coils
Material isolante desconhecidoMaterial isolante desconhecido1 end heads and core insulation
Metal desconhecidoMetal desconhecido1 core fastenings

Ferramentas necessárias:

Método de enrolamento desconhecidoMétodo de enrolamento desconhecido
Torno mecânicoTorno mecânico
5

Switch on and hold

Connect the coils to the supply and put the armature against the faced poles: the magnet holds it with the pull it was sized for. When the armature touches the poles there is practically no leakage between them.

Ferramentas necessárias:

Fonte de alimentação de corrente contínuaFonte de alimentação de corrente contínua

Materiais

4

Ferramentas necessárias

4

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...