Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Sliding-Strip Cylinder Dash Churn: Strips on the Slats Open the Gaps One Way and Close Them the Other
Buttercup

Criado por

Buttercup

10. novembro 2026IE
6
0
0
0
0

Sliding-Strip Cylinder Dash Churn: Strips on the Slats Open the Gaps One Way and Close Them the Other

Daniel K. France of Congress, Ohio, received US 25,404, dated 13 September 1859, for a cylindrical churn-dash. Two crosses of curved arms carry four groups of three slats, each slat half by one inch. On each group a metal strip with a slot down its middle is held by screws in short slots, so it slides when the dash changes direction and opens or closes the spaces between the slats. Turned one way the dash churns; reversed, it gathers the butter into a corner. Two cog wheels at three to one drive it. France gives one size, the slats; every other size here is ours.
Intermediário
About 2 days, plus printing

Instruções

1

France's slats, and the wheels' three to one

A carregar o notebook Jupyter…
2

A turning dasher on crossed arms in a box, before it

That dasher's boards were fixed. France's slats carry strips that open and close the gaps with the turning.
3

Read US 25,404

"The motion of the dash to be to the left in the direction of the curve of the arms while churning, thereby producing the greatest amount of friction in the cream. When butter is produced the motion of the dash is reversed and the butter gathered in the lower left corner of the churn by the reversed action thereon of the dash and self adjusting slide."
4

Print the large cog wheel

The 48-tooth spur wheel (module 3) with a hub, bored 20.4 mm, for the crank's stud. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Arquivo de designSTLCC0 - Free
5

Print the small cog wheel

The 16-tooth spur pinion (module 3) with a hub, bored 20.4 mm, for the dash's shaft. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Arquivo de designSTLCC0 - Free
6

Box with legs and lid

From 20 mm hardwood cut a bottom 440 x 340 mm, two sides 440 x 300 mm, two ends 300 x 300 mm and a lid 440 x 340 mm. Bore each end 20.8 mm through its middle, 150 mm above the floor, for the shaft. Glue and screw the ends between the sides and the box onto the bottom, and screw four legs of 70 mm timber, 350 mm long, under it. Fill the box with water overnight so it swells tight, then empty it.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei3 peças
Madeira macia de 70x70 mmMadeira macia de 70x70 mm1 peça
Cola de madeiraCola de madeira1 peça
Parafusos para madeiraParafusos para madeira30 peças

Ferramentas necessárias:

Serra de mesaSerra de mesa
SerroteSerrote
Berbequim sem fiosBerbequim sem fios
Conjunto de brocas de páConjunto de brocas de pá
Sargento de barraSargento de barra
Esquadro fixoEsquadro fixo
Fita métricaFita métrica
ÁguaÁgua
7

Dash: arms, hubs and slats

Cut eight curved arms from 22 mm hardwood with the jigsaw, each 18 mm wide, sweeping 30 degrees from a 20 mm hub radius out to 112 mm. Glue four into a 56 mm hardwood hub to make a cross, twice, all curving the same way, and bore the hubs 20.4 mm. Cut twelve slats 12.7 x 25.4 mm, 340 mm long, and screw them to the arms' ends in groups of three, 9 mm apart, flat side out, so their faces are 125 mm from the middle.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei1 peça
Cola de madeiraCola de madeira1 peça
Parafusos para madeiraParafusos para madeira24 peças

Ferramentas necessárias:

Serra tico-ticoSerra tico-tico
Serra de mesaSerra de mesa
Berbequim sem fiosBerbequim sem fios
Conjunto de brocas de páConjunto de brocas de pá
Jogo de brocasJogo de brocas
Fita métricaFita métrica
8

Strips B with slots C and screws D

Cut four strips of 0.8 mm stainless sheet, 324 mm long and as wide as a group of slats (94 mm). Cut a slot C 9 mm wide along the middle of each, stopping 30 mm from the ends, and a short slot across each end. Lay each strip on its group's outer face and fix it with an M4 screw through each end slot into the arm's end, just loose enough to slide sideways. Turned one way, the cream pushes each strip so its slot lies over the slats; the other way, over a space.

Materiais para este passo:

Chapa de aço inoxidávelChapa de aço inoxidável1 peça
Parafusos de máquinaParafusos de máquina8 peças
Anilha planaAnilha plana8 peças

Ferramentas necessárias:

Tesoura de chapaTesoura de chapa
Limas (lima de mão)Limas (lima de mão)
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Conjunto de chaves de fendasConjunto de chaves de fendas
9

Shaft, cog wheels and crank

Pass a 20 mm stainless shaft through one end of the box, the two hubs and the other end, and pin the hubs to it. On the outside of the geared end, screw a hardwood block 96 mm above the shaft, fix a 20 mm stud in it, and fit the large wheel on the stud with a crank and handle. Pin the small wheel on the shaft's end meshing with it.

Materiais para este passo:

Varão de aço inoxidávelVarão de aço inoxidável2 peças
Tábua de madeira de leiTábua de madeira de lei1 peça
Cavilhas de madeira duraCavilhas de madeira dura1 peça
Sortido de parafusos sextavadosSortido de parafusos sextavados3 peças
Porca de segurança com anel de nylonPorca de segurança com anel de nylon3 peças
Filamento PETGFilamento PETG1 peça

Ferramentas necessárias:

Impressora 3D de filamento (FDM)Impressora 3D de filamento (FDM)
Serra de arco para metaisSerra de arco para metais
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Chave inglesa ajustávelChave inglesa ajustável
10

The build in 3D

FreeCAD model of this build, front side cut away: the dash's two crosses of curved arms, the four groups of slats with their strips, slots and screws, the shaft through the box's ends, and the two cog wheels and crank outside. The dash was turned through 16 angles.
Arquivo de designBLENDCC0 - Free
11

Churn, then gather

Pour about 6 litres of heavy cream at about 15 °C into the box, checked with the thermometer, and put the lid on. Turn the crank so the dash turns with the curve of its arms, timing it. When the butter comes, turn the crank the other way so the strips slide over and the dash gathers the butter into a corner. Lift it out, drain the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.

Materiais para este passo:

Natas para baterNatas para bater6 l
Sal marinho grossoSal marinho grosso1 peça
ÁguaÁgua1 peça

Ferramentas necessárias:

Termómetro de sonda permanenteTermómetro de sonda permanente
CronómetroCronómetro
Balança digital de cozinhaBalança digital de cozinha
Taça grande de aço inoxidávelTaça grande de aço inoxidável
12

Troubleshooting

Sliding-strip churn troubleshooting.

Flow

Loading...
13

History and honest limits

**Daniel K. France** of Congress, Wayne County, Ohio, US 25,404, 13 September 1859, "Churn-Dash". He claimed the metallic strips B on the convex surface of the slats, held by slots and screws. He disclaimed slats or beaters hinged to the arms. His slats, half by one inch, are kept; every other size is ours. His plates A, changed to reverse the dash when the crank is used alone, are not built.

Materiais

15

Ferramentas necessárias

20

Ficheiros de design

3

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...