Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Foot-Fed Carriage Saw Table: The Saw Rides on Balls Under the Table, a Foot Lever Pulls It Through the Work (Hall, 1933)
Forge

Criado por

Forge

13. novembro 2026NO
7
0
0
0
0

Foot-Fed Carriage Saw Table: The Saw Rides on Balls Under the Table, a Foot Lever Pulls It Through the Work (Hall, 1933)

Harry O. Hall of Murray, Utah, received US 1,930,168, dated 10 October 1933, for a portable saw table where the saw moves and the work stays still. The saw and its motor hang from a carriage under the top. The carriage rolls on balls in V-shaped tracks in a straight line. A foot lever pulls it back through a board held against the fence, and springs bring it forward again. Nuts on a hanging stem set the depth, and a spring under the motor keeps the belts tight. The table rolls on wheels and its back legs fold. The patent gives no sizes; every size here is ours, and our top is plywood where his is folded sheet metal.
Avançado
About 1 week

Instruções

1

The foot lever, the travel and the cut

A carregar o notebook Jupyter…
2

Read US 1,930,168

"The movable saw carriage is mounted to freely move longitudinally of the table in a straight line and is moved into engagement with the piece of work held in position by the work fence, when the lever 29' is depressed by the foot."
3

Table and legs

Make the top 5 of 18 mm plywood 1000 x 600 mm with pine aprons 6, 7 round it, and cut a slot 47 12 mm wide and 500 mm long down its middle. Fix four pine legs 9, 10 splayed outwards at the corners with braces 11 and plywood gussets 12, the top 850 mm high; bolt the rear legs' gussets with one bolt each as a pivot and a second removable bolt, so they fold. Put an axle 15 between the front legs with a wheel 14 on each end.

Materiais para este passo:

Placa de contraplacadoPlaca de contraplacado1 peça
Madeira de pinhoMadeira de pinho6 peças
Barra redonda de aço macioBarra redonda de aço macio1 peça
Conjunto de rodas de borrachaConjunto de rodas de borracha1 peça
Parafuso de carroçariaParafuso de carroçaria8 peças
Parafusos para madeiraParafusos para madeira40 peças
Cola de madeiraCola de madeira1 peça

Ferramentas necessárias:

Serra tico-ticoSerra tico-tico
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Sargento de barraSargento de barra
Esquadro combinadoEsquadro combinado
Fita métricaFita métrica
4

Tracks and carriage

Screw a pine rail 22 along each side under the top and bolt a length of steel angle on it, V upwards, as the track 21. Make the carriage of two more angles 16, V downwards over the tracks, joined near each end by a cross bolt 17 with nuts 19 either side of each angle, so their spacing can be set. Under each end of each carriage angle, between the bolt and a small steel lug 23 bolted inside the angle, put a 10 mm steel ball 20 to roll in the track. Hook two springs 24 from the front wall of the top to the front cross bolt.

Materiais para este passo:

Madeira de pinhoMadeira de pinho1 peça
Cantoneira de aço macioCantoneira de aço macio2 peças
Sortido de parafusos sextavadosSortido de parafusos sextavados12 peças
Varão roscadoVarão roscado1 peça
Porca sextavadaPorca sextavada8 peças
Barra chata de aço macioBarra chata de aço macio1 peça
Rolamentos de esferasRolamentos de esferas1 peça
Mola de traçãoMola de tração2 peças
Parafusos para madeiraParafusos para madeira16 peças

Ferramentas necessárias:

Serra de arco para metaisSerra de arco para metais
RebarbadoraRebarbadora
Engenho de furarEngenho de furar
Jogo de brocasJogo de brocas
Jogo de limasJogo de limas
Torno de bancadaTorno de bancada
Chave inglesa ajustávelChave inglesa ajustável
Óculos de segurançaÓculos de segurança
5

Foot lever and chain

Pivot a hardwood foot lever 29' on the front axle, reaching back along the floor, with a pedal 31 on its free end. Fix a pulley 28 on a shaft 29 between the rear legs. Run a chain 27 from the rear cross bolt of the carriage over the pulley and down to the lever, fixed 450 mm from its pivot. Pressing the pedal pulls the carriage back; letting go, the springs return it.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei1 peça
RoldanaRoldana1 peça
Barra redonda de aço macioBarra redonda de aço macio1 peça
Corrente de rolosCorrente de rolos1 peça
Sortido de parafusos sextavadosSortido de parafusos sextavados3 peças

Ferramentas necessárias:

Serra tico-ticoSerra tico-tico
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Serra de arco para metaisSerra de arco para metais
Chave inglesa ajustávelChave inglesa ajustável
6

Saw frame, arbor and shield

Bolt a rectangle of steel angle as the saw frame 32. Hang one end on the rear cross bolt between two collars 33 with set screws 34, so it can be slid sideways. On the front cross bolt put a sleeve 35 between collars 36 with a threaded stem 38 hanging from it, through a hole 39 in the frame's end, with a clamping nut 40 above and below: these set the saw's height. Bolt two flange bearings 42 across the frame and fit a 30 mm arbor 43 turned with a collar, a loose flange and an M20 thread; put the 250 mm blade on one end, centred under the slot, and a V-belt pulley 49 on the other. Bend a sheet steel shield 48 round the lower half of the blade and bolt it to the frame.

Materiais para este passo:

Cantoneira de aço macioCantoneira de aço macio1 peça
Barra redonda de aço macioBarra redonda de aço macio2 peças
Parafuso sem cabeça de ponta côncavaParafuso sem cabeça de ponta côncava4 peças
Varão roscadoVarão roscado1 peça
Porca sextavadaPorca sextavada4 peças
Mancal de flangeMancal de flange2 peças
Circular Saw Blade SetCircular Saw Blade Set1 peça
Polia para correia trapezoidal (secção A)Polia para correia trapezoidal (secção A)1 peça
Chapa de aço macioChapa de aço macio1 peça
Sortido de parafusos sextavadosSortido de parafusos sextavados10 peças

Ferramentas necessárias:

Serra de arco para metaisSerra de arco para metais
RebarbadoraRebarbadora
Engenho de furarEngenho de furar
Jogo de brocasJogo de brocas
Jogo de machos e cossinetesJogo de machos e cossinetes
Desandador de machosDesandador de machos
Torno mecânicoTorno mecânico
Placa de torno de 3 castanhasPlaca de torno de 3 castanhas
Ferramenta de corte para tornoFerramenta de corte para torno
Paquímetro digital de 6 polegadasPaquímetro digital de 6 polegadas
Tesoura de chapaTesoura de chapa
Torno de bancadaTorno de bancada
Chave inglesa ajustávelChave inglesa ajustável
Jogo de chaves AllenJogo de chaves Allen
7

Motor frame

Bolt a shorter angle frame 53 inside the saw frame, pivoted on the same rear cross bolt, and bolt the motor 51 under it with a V-belt pulley 50 in line with the arbor's. Hang its free end from a bolt 55 off a sleeve 56 on a rod 57 across the saw frame, with a spring 61 and washer 62 on the bolt above the motor frame and a nut 59 below. Fit the belt 52 and set its tension with the nut. Have the motor wired to a switch at the front.

Materiais para este passo:

Cantoneira de aço macioCantoneira de aço macio1 peça
Motor elétricoMotor elétrico1 peça
Polia para correia trapezoidal (secção A)Polia para correia trapezoidal (secção A)1 peça
Correia trapezoidal (secção A)Correia trapezoidal (secção A)1 peça
Barra redonda de aço macioBarra redonda de aço macio1 peça
Varão roscadoVarão roscado1 peça
Coil SpringCoil Spring1 peça
Anilha planaAnilha plana2 peças
Porca sextavadaPorca sextavada2 peças
Sortido de parafusos sextavadosSortido de parafusos sextavados6 peças
Interruptor de ligar/desligarInterruptor de ligar/desligar1 peça

Ferramentas necessárias:

Serra de arco para metaisSerra de arco para metais
Engenho de furarEngenho de furar
Jogo de brocasJogo de brocas
Chave inglesa ajustávelChave inglesa ajustável
Jogo de chaves AllenJogo de chaves Allen
8

Fence and first cut

Fix a hardwood fence 63 across the top near its rear end, standing past both sides, held by hook bolts 64 that hook under steel flanges 66 screwed to the gussets, with nuts 67. Set the blade 10 mm above the board's thickness with the stem's nuts. Hold a board against the fence, start the motor and press the pedal: the saw comes back through the board. Let the pedal up and it returns.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei1 peça
Varão roscadoVarão roscado1 peça
Porca sextavadaPorca sextavada2 peças
Barra chata de aço macioBarra chata de aço macio1 peça
Parafusos para madeiraParafusos para madeira8 peças

Ferramentas necessárias:

Serra tico-ticoSerra tico-tico
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Esquadro combinadoEsquadro combinado
Óculos de segurançaÓculos de segurança
Proteção auditiva (abafadores, SNR 30 dB)Proteção auditiva (abafadores, SNR 30 dB)
9

Troubleshooting

Carriage saw troubleshooting.

Flow

Loading...
10

History and honest limits

**Harry O. Hall** of Murray, Utah, US 1,930,168, dated 10 October 1933, filed 21 March 1933. He claimed a top with a longitudinal slot, "a traveling carriage mounted beneath said top and movable longitudinally thereof", a saw frame pivoted on one cross bar and hung from the other on a stem with nuts above and below, and a motor frame hung from the saw frame on a bolt with a spring. His top is folded sheet metal on splayed legs; ours is plywood on pine. His balls are confined between the cross bolts and lugs; ours the same, in steel angle. He gives no sizes; every size here is ours.

Materiais

27

Ferramentas necessárias

22

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...