Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL

Rotating-Receiver Stationary-Break Churn: The Whole Cream Vessel Turns, a Narrow Fixed Break Churns It
Mortimer S. Harsha of Sycamore, Illinois, received US 26,459, dated 13 December 1859, for what he called the "Vertical Rotating and Stationary Break Churn". Instead of a dasher, the whole cream vessel turns on an upright shaft with a pointed foot, driven by a gear and crank below it, while one narrow perforated break, fixed to a removable top, stands still near the vessel's side. The turning cream keeps going like a balance wheel, so little effort keeps it churning.
The patent gives no sizes; every size here is ours.
Intermediário
About a day, plus printing
Instruções
1
1
The turning cream against a still break
The turning cream against a still break
A carregar o notebook Jupyter…
2
2
Fixed brakes in turning cream, three months before
Fixed brakes in turning cream, three months before
Taylor turned a dasher among fixed brakes. Harsha turns the vessel itself against a single fixed break.
3
3
Read US 26,459
Read US 26,459
"This is accomplished by said break presenting only a small resisting surface to the moving cream, while the cream being made to rapidly rotate on said vertical or upright shaft only against said break dash, becomes, along with its receiver, a receptacle of the power applied, similar to that of a balance wheel, and so by its own accumulative force, when power is once applied, puts it in motion"
4
4
Print the gear wheel G
Print the gear wheel G
Crown wheel, 36 teeth on its face, module 2, with a hub bored 12.4 mm and a cross hole for a pin. PETG, 0.2 mm layers, 40 % infill, 4 walls.
5
5
Print the pinion
Print the pinion
Spur pinion, 12 teeth, module 2, with a long hub bored 16.4 mm and a cross hole for a pin. PETG, 0.2 mm layers, 40 % infill, 4 walls.
6
6
Print the socket
Print the socket
A cup 50 mm across and 22 mm tall with a cone recess for the shaft's point. PETG, 0.2 mm layers, 40 % infill, 4 walls.
7
7
Print the flange
Print the flange
A disc 200 mm across and 15 mm thick bored 16.6 mm, to carry the receiver. Print with 100 % infill. PETG, 0.2 mm layers, 40 % infill, 4 walls.
8
8
Base E, brace H, posts F and top D
Base E, brace H, posts F and top D
Make a hardwood base 600 x 600 mm and screw the socket in its middle. Screw a brace H to it, an upright 30 x 40 mm with an arm reaching over the socket, bored 16.6 mm 25 to 55 mm up as the shaft's journal box. Tenon two posts 30 x 50 mm, 515 mm tall, into the base 490 mm apart, and make a top board 550 x 160 x 20 mm with mortises to drop onto their tenons so it lifts off. Set two chairs 44 x 30 mm, 124 mm tall, for the gear wheel's shaft.
Materiais para este passo:
Tábua de madeira de lei3 peças
Cola de madeira1 peça
Parafusos para madeira20 peças
Filamento PETG1 peçaFerramentas necessárias:
Impressora 3D de filamento (FDM)
Serra de mesa
Serra tico-tico
Formão de samblagem
Maço de madeira
Berbequim sem fios
Jogo de brocas
Sargento de barra
Fita métrica9
9
Shaft C, receiver A and gearing
Shaft C, receiver A and gearing
File one end of a 16 mm stainless shaft 170 mm long to a point. Pin the pinion and the flange on it, stand its point in the socket through the journal box, and bolt the stockpot's bottom to the flange with stainless screws sealed with silicone. Fit the crown wheel on a 12 mm stainless shaft through the chairs, meshing under the pinion, with a crank and handle on its end.
Materiais para este passo:
Varão de aço inoxidável2 peças
Panela alta1 peça
Parafusos de máquina4 peças
Porca de segurança com anel de nylon4 peças
Anilha plana8 peças
Cavilhas de madeira dura1 peçaFerramentas necessárias:
Serra de arco para metais
Limas (lima de mão)
Berbequim sem fios
Jogo de brocas
Chave inglesa ajustável
Conjunto de chaves de fendas10
10
Break dash B
Break dash B
Cut a hardwood break 60 x 15 mm long enough to reach from the top board to 25 mm above the receiver's floor, bore ten 16 mm holes through it, and fix it by a tenon through the top board so it hangs 30 mm in from the receiver's side.
Materiais para este passo:
Tábua de madeira de lei1 peça
Cola de madeira1 peçaFerramentas necessárias:
Serra de mesa
Conjunto de brocas de pá
Berbequim sem fios
Formão de samblagem
Maço de madeira
Lixa11
11
The build in 3D
The build in 3D
FreeCAD model of this build, the receiver cut through the middle: the base with its socket, brace and posts, the shaft with pinion and flange, the crown wheel and crank, the turning receiver and the fixed perforated break hanging from the top.
12
12
Churn
Churn
Lift the top off, pour about 9 litres of heavy cream at about 15 °C into the receiver, checked with the thermometer, and put the top back. Turn the crank steadily, timing it: once the cream is moving it keeps going with little effort. When the butter comes, lift the top and break out, take out the butter, drain the buttermilk, wash the butter in cold water until it runs clear, salt and weigh it.
Materiais para este passo:
Natas para bater9 l
Sal marinho grosso1 peça
Água1 peçaFerramentas necessárias:
Termómetro de sonda permanente
Cronómetro
Balança digital de cozinha
Taça grande de aço inoxidável13
13
Troubleshooting
Troubleshooting
Rotating-receiver churn troubleshooting.
Flow
Loading...
14
14
History and honest limits
History and honest limits
**Mortimer S. Harsha** of Sycamore, DeKalb County, Illinois, assignor to himself, Rufus S. Sanborn and H. B. Jones, US 26,459, 13 December 1859, "Churn". He claimed: "An entirely stationary break dash in combination with a cream receiver, made to rotate on a vertical or upright shaft". His break is made "of such size as the relative size of the machine requires, and of any common form or shape"; the patent gives no sizes, and every size here is ours. His receiver was tin, zinc or wood; ours is a stainless stockpot.
Materiais
14- 3 peçasReferência
- 2 peçasReferência
- 20 peçasReferência
- 1 peçaReferência
- 2 peçasReferência
- 1 peçaReferência
- 4 peçasReferência
- Referência
- 8 peçasReferência
- 1 peçaReferência
- 1 peçaReferência
- Referência
- 1 peçaReferência
- 1 peçaReferência
Ferramentas necessárias
19- Referência
- 1 vendor sell this, none ship to you yetReferência
- 1 vendor sell this, none ship to you yetReferência
- Referência
- Referência
- 1 vendor sell this, none ship to you yetReferência
- Referência
- Referência
- 1 vendor sell this, none ship to you yetReferência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
Ficheiros de design
5Blueprints relacionados
Estes blueprints compartilham conhecimento — técnicas, materiais ou princípios

Brake-and-Ledge Bar Dasher Churn: Slotted Brakes Break the Current, Ledges Turn It Back to the Dasher
por Buttercup
Marcenaria
10
0
0
0
0
0

Atmospheric Barrel Churn: Reversed Concave Dashers Close to the Staves, Fresh or Warmed Air Piped to the Middle
por Buttercup
Marcenaria
6
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
por TheChef
ARTESANATO
63
0
0
0
0
0
CC0 Domínio Público
Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.
Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

