Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Counter-Turning Hooped Beater Churn: One Bevel Wheel Turns a Spindle and a Hollow Shaft Opposite Ways, Spiral Hoops Sweep the Wall
Buttercup

Criado por

Buttercup

11. novembro 2026IE
8
0
0
0
0

Counter-Turning Hooped Beater Churn: One Bevel Wheel Turns a Spindle and a Hollow Shaft Opposite Ways, Spiral Hoops Sweep the Wall

William Bently Hopkins of Oakfield, New York, received US 31,806, dated 26 March 1861, for a churn whose crank turns one bevel wheel between two pinions, one above and one below, so a spindle and a hollow shaft round it turn opposite ways. The spindle carries two slats; the hollow shaft carries a slat at its foot and, through two hoops that spiral a quarter turn down beside the wall, a second slat between the spindle's two. The hoops sweep back the cream that would lodge against the wall. The cover lifts off with the gearing and the beaters come out. The patent gives no sizes; every size here is ours.
Intermediário
About 2 days

Instruções

1

Two sets turning against each other

A carregar o notebook Jupyter…
2

Parts turning opposite ways in one churn, a year before

Ward turns a ribbed cylinder one way and dashers the other. Hopkins turns two sets of beaters on a spindle and a hollow shaft from one bevel wheel.
3

Read US 31,806

"The hoops n n ... not only maintain the relative position between k and m, but have a specific effect in displacing and agitating that portion of the milk or cream which would, by the operation of the two sets of beaters, be forced and impacted against the walls of the vessel, where they would, if allowed to remain, escape the action of the beaters, to a considerable extent."
4

Print the step

The step on the bucket's floor: 40 mm across, 12 high, with a 12.8 mm hole 8 deep. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Arquivo de designSTLCC0 - Free
5

Body A and cover B

Use a 20-litre food-grade bucket as the body A and set the printed step in the middle of its floor. Cut a 12 mm HDPE cover B to its top, bore it 23 mm at the centre, and saw it across through the hole into two halves.

Materiais para este passo:

Balde de 20 litrosBalde de 20 litros1 peça
Chapa de PEADChapa de PEAD1 peça
Filamento PETGFilamento PETG1 peça

Ferramentas necessárias:

Impressora 3D de filamento (FDM)Impressora 3D de filamento (FDM)
BússolaBússola
Serra tico-ticoSerra tico-tico
Conjunto de brocas de páConjunto de brocas de pá
Berbequim sem fiosBerbequim sem fios
6

Spindle G and slats j

Cut a 12 mm stainless spindle G 580 mm long. Plane two hardwood slats j 220 x 30 x 8 mm, bore each 12.2 mm at the middle with a hardwood hub, and pin them on the spindle 30 and 130 mm above its foot, a quarter turn apart, each tilted 20 degrees about its length.

Materiais para este passo:

Varão de aço inoxidávelVarão de aço inoxidável1 peça
Tábua de madeira de leiTábua de madeira de lei1 peça
Cavilhas de madeira duraCavilhas de madeira dura1 peça
Cola de madeiraCola de madeira1 peça

Ferramentas necessárias:

Serra de mesaSerra de mesa
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Serra de arco para metaisSerra de arco para metais
Limas (lima de mão)Limas (lima de mão)
7

Hollow shaft H, slats k and m, hoops n

Cut a 22 mm stainless tube H 270 mm long. Plane two hardwood slats k and m 250 x 30 x 8 mm, tilted 20 degrees the other way. Fix k on the tube's foot with a hardwood hub. Bore m 13.2 mm at its hub so it turns loose on the spindle, and slide it on between the two j slats. Bend two strips of stainless strip 20 mm wide into hoops n that run a quarter turn round at 124 mm radius while dropping 100 mm, and screw each from an end of k down to the end of m a quarter turn round, so m lies at right angles to k. Slide the tube down over the spindle.

Materiais para este passo:

Tubo de aço inoxidávelTubo de aço inoxidável1 peça
Tábua de madeira de leiTábua de madeira de lei1 peça
Fita de aço inoxidável laminada a frio (420)Fita de aço inoxidável laminada a frio (420)1 peça
Parafusos para madeiraParafusos para madeira8 peças
Cola de madeiraCola de madeira1 peça

Ferramentas necessárias:

Serra de mesaSerra de mesa
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Serra de arco para metaisSerra de arco para metais
Tesoura de chapaTesoura de chapa
Torno de bancadaTorno de bancada
Maço de borrachaMaço de borracha
Conjunto de chaves de fendasConjunto de chaves de fendas
8

Print the pinion f

The lower pinion f on the hollow shaft: 14 teeth, module 2.5, 22.2 mm bore. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Arquivo de designSTLCC0 - Free
9

Print the pinion e

The upper pinion e on the spindle: 14 teeth, module 2.5, 12.2 mm bore; fit it hub up. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Arquivo de designSTLCC0 - Free
10

Print the driving wheel C

The driving wheel C: a crown wheel of 42 teeth, module 2.5, 16.2 mm bore. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Arquivo de designSTLCC0 - Free
11

Frame, wheel C, pinions e and f, crank D

Screw two hardwood posts 30 x 40 mm, 195 tall, to the cover either side of its centre, 150 mm apart over their inner faces, and join their tops with a top bar bored 12.6 mm over the centre. Screw two hardwood bearing blocks 50 x 25 mm, 120 tall, to the cover 60 and 125 mm in front of the centre, bored 16.6 mm across 96 mm above the cover. Pin the pinion f on the hollow shaft 40 mm above the cover and the pinion e on the spindle 105 mm above f, teeth facing each other. Run a 16 mm stainless shaft 150 mm long through the blocks with the crown wheel C pinned on its inner end between the two pinions, meshing both, a shaft collar, and a crank D of mild steel flat bar, 100 mm throw, with a hardwood handle.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei1 peça
Varão de aço inoxidávelVarão de aço inoxidável1 peça
Shaft CollarShaft Collar1 peça
ContrapinoContrapino4 peças
Barra chata de aço macioBarra chata de aço macio1 peça
Cavilhas de madeira duraCavilhas de madeira dura1 peça
Parafusos para madeiraParafusos para madeira12 peças
Filamento PETGFilamento PETG1 peça

Ferramentas necessárias:

Impressora 3D de filamento (FDM)Impressora 3D de filamento (FDM)
Serra de mesaSerra de mesa
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Serra de arco para metaisSerra de arco para metais
Limas (lima de mão)Limas (lima de mão)
Torno de bancadaTorno de bancada
Conjunto de chaves de fendasConjunto de chaves de fendas
12

The build in 3D

FreeCAD model of this build, the bucket cut open: the step, the spindle with its two slats, the hollow shaft with its slat, the loose slat and the two spiral hoops, the cover, posts and top bar, the crown wheel between the two pinions, and the crank.
Arquivo de designBLENDCC0 - Free
13

Churn

Pour about 10 litres of heavy cream at about 15 °C, checked with the thermometer, into the bucket with the beaters in, lay on the cover halves and seat the gearing. Turn the crank steadily, timing it. When the butter comes, lift off the cover and gearing, lift out the beaters, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

Materiais para este passo:

Natas para baterNatas para bater10 l
Sal marinho grossoSal marinho grosso1 peça
ÁguaÁgua1 peça

Ferramentas necessárias:

Termómetro de sonda permanenteTermómetro de sonda permanente
CronómetroCronómetro
Balança digital de cozinhaBalança digital de cozinha
Taça grande de aço inoxidávelTaça grande de aço inoxidável
14

Troubleshooting

Hooped-beater churn troubleshooting.

Flow

Loading...
15

History and honest limits

**Wm. Bently Hopkins** of Oakfield, Genesee County, New York, US 31,806, 26 March 1861, "Churn". He claimed "the beaters j j and k, m, the latter provided with spiral arms, n n", and did not claim beaters on separate shafts turning opposite ways as such. His text says the hoops run a quarter of the circle, putting m at right angles to k, and also that m is forty-five degrees in advance of k; we follow the hoops. His gearing was a bevel wheel between two bevel pinions; ours is a printed crown wheel. The patent gives no sizes; every size here is ours.

Materiais

16

Ferramentas necessárias

17

Ficheiros de design

5

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...