Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Instant-Read Thermometer: Digital, with a Stainless Probe That Pivots on the Case (Cook, US 5,018,875, 1991)
Penny

Criado por

Penny

3. novembro 2026DK
10
0
0
0
0

Instant-Read Thermometer: Digital, with a Stainless Probe That Pivots on the Case (Cook, US 5,018,875, 1991)

A pocket digital thermometer. A thin stainless steel probe with a thermistor in its tip pivots on a small, flat-sided case, so you can push the probe into food and turn the display to face you. A button cell runs a chip and a liquid crystal display, and a push button updates the reading at once. The angled case will not roll off a table. Result: a thin-probe digital thermometer for food and air. Source: T. A. Cook (PSG Industries), US 5,018,875 (1991). Unknown: the circuit, the range, the case size. Picture: the patent drawing.
Intermediário
Unknown

Instruções

1

Make the probe

Cut a type 304 stainless steel tube about 0.166 in (4.0 mm) across and 5 in (120 mm) long, and close one end. Set a thermistor inside the closed tip and run its two wires up the tube. Aluminium or titanium would also serve.

Materiais para este passo:

Tubo de aço inoxidávelTubo de aço inoxidável1 probe
Conjunto de termístores NTCConjunto de termístores NTC1 thermistor
Fio de cobreFio de cobre1 interconnecting wires

Ferramentas necessárias:

Serra de arco para metaisSerra de arco para metais
Ferro de soldarFerro de soldar
2

Mould the pivot boss and case

Mould from ABS a cylindrical pivot boss with a recess for the probe's open end and a channel right through it for the wires. Mould the case in an upper and a lower half that snap together, wider at the display end and tapering to the probe end so it cannot roll, with two projecting supports at the probe end, each with a pivot hole. Not given: the sizes.

Materiais para este passo:

Granulado de ABSGranulado de ABS1 boss and case

Ferramentas necessárias:

Máquina de moldação por injeçãoMáquina de moldação por injeção
Dimensões desconhecidasDimensões desconhecidas
3

Fit the electronics and assemble

In the case, fit an integrated circuit that turns the thermistor's resistance into a reading on a liquid crystal display at the wide end, with a push button beside it that updates the reading at once. Add a compartment for a 1.5 V button cell (Eveready E675, IEC R07) under a cover that locks with a quarter turn. Push the probe into the boss, lead the wires through the channel to the circuit, and clamp the boss ends in the pivot holes as the halves snap together; friction holds whatever angle you set. In use, push the probe in, turn the display to face you and press the button. Not given: the circuit (the patent points to US 4,536,851).

Materiais para este passo:

Placa de circuito impressoPlaca de circuito impresso1 peça
Circuito integradoCircuito integrado1 peça
Visor LCD de segmentosVisor LCD de segmentos1 peça
Botão de pressãoBotão de pressão1 peça
Pilha de botão de 1,5 VPilha de botão de 1,5 V1 peça
Fio de soldaFio de solda1 as needed

Ferramentas necessárias:

Ferro de soldarFerro de soldar

Materiais

10

Ferramentas necessárias

4

Blueprints relacionados

Estes blueprints compartilham conhecimento — técnicas, materiais ou princípios

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...