Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Cam-Arm Tubing Cutter: Two Swinging Arms Keep the Wheel and Rollers Evenly Round Any Tube (Lutsker, 1959)
Forge

Criado por

Forge

13. novembro 2026NO
7
0
0
0
0

Cam-Arm Tubing Cutter: Two Swinging Arms Keep the Wheel and Rollers Evenly Round Any Tube (Lutsker, 1959)

Simon Lutsker of Shaker Heights, Ohio, received US 2,870,536, dated 27 January 1959, for a tubing cutter that grips small and large tubes equally well. The wheel turns under a housing at the foot of a guide. A block slides up the guide on a screw. Two arms hang from the block, each with a roller at its lower end. Springs press the arms' curved cam edges against rollers on the housing. As the screw draws the block up, the arms swing inwards or outwards, so the wheel and the two rollers stay about evenly spaced round the tube, whatever its size. We worked out the cam so the three contacts are exactly 120 degrees apart. The curve comes out as an arc, as in his patent. All sizes are ours.
Avançado
About 4 days

Instruções

1

Three points evenly round

A carregar o notebook Jupyter…
2

Read US 2,870,536

"Irrespective of the size of the tubing which is being cut, the points of engagement of the cutter wheel 21 and support rollers 32 with the tubing will always be substantially equidistant from each other circumferentially of the tubing."
3

Print the template

The arm plate with its cam edge, the housing and the guide block at 1:1, with holes, slots and sizes. print at 100 % (check the 50 mm bar).
Arquivo de designPDFCC0 - Free
4

Cut the arm plates

Glue four copies of the arm outline on 3 mm steel plate. Saw and file them to the line, taking the cam edge slowly and checking it against the template. Clamp them in a stack and drill the 4 mm pivot and roller-pin holes and the two 3 mm holes through all four together.

Materiais para este passo:

Chapa grossa de aço macioChapa grossa de aço macio1 peça

Ferramentas necessárias:

Serra de arco para metaisSerra de arco para metais
Jogo de limasJogo de limas
Jogo de limas de agulhaJogo de limas de agulha
Engenho de furarEngenho de furar
Morsa de máquinaMorsa de máquina
Jogo de brocasJogo de brocas
Punção de centroPunção de centro
Torno de bancadaTorno de bancada
Paquímetro digital de 6 polegadasPaquímetro digital de 6 polegadas
5

Make the housing

From 30 x 20 flat bar, saw a block 64 mm long and file it to 28 x 18 mm, leaving the two ears below its middle. Saw the forked ends: two cuts 14.4 mm apart, 20 mm in from each end, and break out the middle. Saw and file a 7 mm slot up between the ears for the wheel. Drill the 5 mm shaft hole across the ears, the 4 mm housing-roller pins across the forks, and the 4 mm rivet hole. File a groove 20 mm wide and 3 mm deep down each face for the guide's legs.

Materiais para este passo:

Barra chata de aço macioBarra chata de aço macio1 peça

Ferramentas necessárias:

Serra de arco para metaisSerra de arco para metais
Jogo de limasJogo de limas
Engenho de furarEngenho de furar
Morsa de máquinaMorsa de máquina
Jogo de brocasJogo de brocas
Torno de bancadaTorno de bancada
Paquímetro digital de 6 polegadasPaquímetro digital de 6 polegadas
Ponta de traçarPonta de traçar
6

Make the block and the guide

Saw the guide block from the same bar, 60 x 18 x 28 mm, with forked ends from 14 mm out, the 4 mm pivot holes, the 3 mm spring-pin holes and the leg grooves. Drill 8.5 mm up its middle and tap M10. Bend a 20 x 3 mm flat bar into an inverted U with its legs 22 mm apart inside and 69 mm high, and drill a 10.5 mm hole in its top.

Materiais para este passo:

Barra chata de aço macioBarra chata de aço macio2 peças

Ferramentas necessárias:

Serra de arco para metaisSerra de arco para metais
Jogo de limasJogo de limas
Engenho de furarEngenho de furar
Morsa de máquinaMorsa de máquina
Jogo de brocasJogo de brocas
Jogo de machos e cossinetesJogo de machos e cossinetes
Torno de bancadaTorno de bancada
Martelo de bolaMartelo de bola
Paquímetro digital de 6 polegadasPaquímetro digital de 6 polegadas
7

Turn the rollers and the wheel shaft

Turn two housing rollers 10 mm across and 14 mm long, and two lower rollers 12 mm across and 7.6 mm long, from mild steel bar, all bored 4.2 mm. For the wheel shaft, turn a 6 mm rod to 5 mm, leaving a 6 mm head, file a flat on the head, and turn a groove near the other end.

Materiais para este passo:

Barra redonda de aço macioBarra redonda de aço macio1 peça
Varão de aço macioVarão de aço macio1 peça

Ferramentas necessárias:

Torno mecânicoTorno mecânico
Placa de torno de 3 castanhasPlaca de torno de 3 castanhas
Ferramenta de corte para tornoFerramenta de corte para torno
Goiva de sangrarGoiva de sangrar
Jogo de brocasJogo de brocas
Jogo de limasJogo de limas
Paquímetro digital de 6 polegadasPaquímetro digital de 6 polegadas
8

Turn the cutting wheel

Chuck a tool steel bar and face it. Turn the end to 20 mm across for 10 mm, centre drill and drill a 5 mm hole 10 mm deep, and turn the edge to a 50 degree vee, 25 degrees each side, sharp in the middle of the 6 mm width. Part it off 6 mm long and take the burr off the hole.

Materiais para este passo:

Barra de aço-ferramentaBarra de aço-ferramenta1 peça

Ferramentas necessárias:

Torno mecânicoTorno mecânico
Placa de torno de 3 castanhasPlaca de torno de 3 castanhas
Ferramenta de corte para tornoFerramenta de corte para torno
Goiva de sangrarGoiva de sangrar
Conjunto de brocas de centrarConjunto de brocas de centrar
Jogo de brocasJogo de brocas
Paquímetro digital de 6 polegadasPaquímetro digital de 6 polegadas
Óculos de segurançaÓculos de segurança
9

Harden and temper

Heat the wheel to a cherry red, until a magnet no longer sticks, and quench it in water, moving it about. Rub it bright with a stone, warm it on a piece of steel plate over the fire, and quench again as soon as it turns a light straw colour.

Ferramentas necessárias:

ForjaForja
Tenaz de forjaTenaz de forja
Íman pequenoÍman pequeno
Balde de têmperaBalde de têmpera
ÁguaÁgua
Pedra de amolarPedra de amolar
Luvas de soldadorLuvas de soldador
Óculos de segurançaÓculos de segurança
10

Make the springs

From spring steel strip, cut two strips 8 mm wide and 30 mm long for the arm springs, and one 6 mm wide and 25 mm long to hold the wheel shaft. Bend each arm spring so it presses on its arm's spring pin and pushes the arm outwards. Drill a hole in the end of each for its pin or screw.

Materiais para este passo:

Fita de aço-molaFita de aço-mola1 peça

Ferramentas necessárias:

Serra de arco para metaisSerra de arco para metais
Jogo de limasJogo de limas
Engenho de furarEngenho de furar
Jogo de brocasJogo de brocas
Torno de bancadaTorno de bancada
11

Make the screw

Cut 90 mm of M10 threaded rod. Lock two nuts together 25 mm from its top as the flange. Put it up through the guide's top hole, add two washers as the spacer, then a nut locked with a second one. Drill a 6 mm hole across the top end and fit a 70 mm piece of 6 mm rod as the T-handle.

Materiais para este passo:

Varão roscadoVarão roscado1 peça
Porca sextavadaPorca sextavada4 peças
Anilha planaAnilha plana2 peças
Varão de aço macioVarão de aço macio1 peça

Ferramentas necessárias:

Chave inglesa ajustávelChave inglesa ajustável
Engenho de furarEngenho de furar
Jogo de brocasJogo de brocas
Serra de arco para metaisSerra de arco para metais
Martelo de bolaMartelo de bola
12

Assemble

Pin each arm pair together with its lower roller between the plates, and with short tubes as spacers on the pivot and spacer pins. Pin the arms into the block's forked ends. Fit the housing rollers in the housing's forks and the wheel on its shaft, with the flat spring screwed to the housing and sitting in the shaft's groove. Screw the block onto the screw, feed the arms down through the housing's forks inside its rollers, and rivet the guide's legs into the housing's grooves. Pin the arm springs to the block. Oil every pin and the screw.

Materiais para este passo:

Pino cilíndrico de açoPino cilíndrico de aço8 peças
Rebites de açoRebites de aço1 peça
Parafuso de cabeça cilíndrica com sextavado interiorParafuso de cabeça cilíndrica com sextavado interior1 peça

Ferramentas necessárias:

Martelo de bolaMartelo de bola
Punção de centroPunção de centro
Torno de bancadaTorno de bancada
Jogo de chaves AllenJogo de chaves Allen
Óleo de corteÓleo de corte
13

Cut a copper tube

Mark a copper tube and hold it in a vice with soft jaws, or by hand for small tubes. Turn the handle to open the arms, put the cutter over the tube, and turn it back until the rollers lift the tube against the wheel. Check by eye that the wheel and rollers look evenly spaced. Turn the cutter once round, give the screw about a quarter turn, and go on until the tube parts. The wheel should run in its own groove; the end should be square and not squeezed oval. Clean the inside of the end with a deburring tool.

Materiais para este passo:

Tubo de cobreTubo de cobre1 peça

Ferramentas necessárias:

Torno de bancadaTorno de bancada
Rebarbador manualRebarbador manual
Paquímetro digital de 6 polegadasPaquímetro digital de 6 polegadas
14

Troubleshooting

Cam-arm tubing cutter troubleshooting.

Flow

Loading...
15

History and honest limits

**Simon Lutsker** of Shaker Heights, Ohio, US 2,870,536, dated 27 January 1959, filed 26 August 1957. He claimed "a guide block mounted for movement along said guide member and movable by said screw means, a pair of cammable members pivotally secured to said guide block" and the springs pressing their "arcuate cam surfaces" against the housing rollers. He said the contacts stay "substantially" equidistant; ours are set exactly 120 degrees apart. The patent gives no sizes or cam radius; all of ours are ours.

Materiais

13

Ferramentas necessárias

29

Ficheiros de design

1

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...