Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL

Floating-Breaker Churn: A Propeller Dasher Under a Breaker That Floats in Wall Grooves, a Water Tube Held by the Faucet
Edward Lynch of Buffalo, New York, received US 27,864, dated 10 April 1860, for a churn. Propeller blades at the bottom of an upright crank-driven shaft drive the cream up against a breaker that floats on it: a ring round the shaft with bevelled arms whose ends ride loosely in grooves in the churn's sides, so it keeps its place at the surface for any amount of cream. A flat tube of warm or cold water stands inside, held by the faucet that also draws off the buttermilk.
The patent gives no sizes; every size here is ours.
Intermediário
About 2 days, plus printing
Instruções
1
1
A breaker that floats
A breaker that floats
A carregar o notebook Jupyter…
2
2
Paddles under a fixed partition, three weeks before
Paddles under a fixed partition, three weeks before
Sangster's partition is fixed below the cream. Lynch's breaker floats on top of it.
3
3
Read US 27,864
Read US 27,864
"They fit loosely in the grooves, so as to allow the breaker to float, upon the milk or cream, and hence always retain the same relation to the milk or cream, whether there be a large or small quantity in the churn."
4
4
Print the dash blades J
Print the dash blades J
Two-blade propeller 190 mm across, blades 80 x 50 x 5 mm pitched 30 degrees, on a hub bored 16.4 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
5
5
Print the water tube L
Print the water tube L
Flat open-topped tank 160 x 30 mm and 210 deep, 3 mm walls, curved to stand against the bucket's side, with a collar under its foot to hold the faucet's nut. PETG, 0.2 mm layers, 100 % infill; fill it with water and check it holds before use.
6
6
Print the crown wheel
Print the crown wheel
Crown wheel, 36 teeth on its face, module 2, with a hub; bored 12.4 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
7
7
Print the pinion
Print the pinion
Spur pinion, 12 teeth, module 2, with a hub; bored 12.4 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
8
8
Grooves i, breaks K and the faucet M
Grooves i, breaks K and the faucet M
Screw three pairs of hardwood strips 20 x 22 mm, 335 long, upright inside the bucket a third of a turn apart, 24 mm apart in each pair, as the grooves i. Screw two triangular hardwood breaks K, 30 mm deep and 150 tall, to the side near the floor between them, and seal every screw hole outside with silicone. Bore the bucket 22 mm, 30 mm above the floor and opposite the third groove, for the spigot. Set the tank against the side there, pass the spigot through the side and screw it into its nut, set in the tank's collar, so it holds the tank and opens into the churn.
Materiais para este passo:
Balde de 20 litros1 peça
Tábua de madeira de lei1 peça
Parafusos para madeira16 peças
Torneira de PVC1 peça
Filamento PETG1 peçaFerramentas necessárias:
Impressora 3D de filamento (FDM)
Serra de mesa
Conjunto de serras-copo
Berbequim sem fios
Jogo de brocas
Conjunto de chaves de fendas
Chave inglesa ajustável
Fita métrica9
9
Floating breaker H
Floating breaker H
Cut a hardwood ring 100 mm across with a 60 mm hole and 50 deep. Cut three hardwood arms 20 mm thick and 50 deep, bevelled so the lower edge is 4 mm thick, the bevel facing the opposite way to the propeller's blades, long enough to reach loosely into the grooves; glue and screw them into the ring a third of a turn apart.
Materiais para este passo:
Tábua de madeira de lei1 peça
Cola de madeira1 peça
Parafusos para madeira6 peçasFerramentas necessárias:
Serra de mesa
Conjunto de serras-copo
Berbequim sem fios
Jogo de brocas
Lixa
Sargento de barra
Conjunto de chaves de fendas10
10
Shaft B, cover P and gearing
Shaft B, cover P and gearing
Screw a hardwood step 50 x 50 x 6 mm to the floor's centre, bored 17 mm, 5 deep. Cut a 16 mm stainless shaft 465 mm long and turn or file its top 77 mm down to 12 mm; fit the propeller 8 mm above the floor. Cut a cover P of HDPE sheet to lie on the rim, bored 20 mm in the centre. Cut a hardwood cross piece N 350 x 205 x 25 mm with two hardwood fingers O 30 x 30 x 20 mm under it to rest on the cover, bored 13 mm for the shaft; fit the pinion above it, two chairs with a 12 mm crank shaft and the crown wheel, and a hardwood crank D with a dowel handle.
Materiais para este passo:
Bloco de madeira dura1 peça
Varão de aço inoxidável2 peças
Chapa de PEAD1 peça
Tábua de madeira de lei2 peças
Cavilhas de madeira dura1 peça
Cola de madeira1 peça
Parafusos para madeira10 peças
Shaft Collar2 peças
Contrapino1 peçaFerramentas necessárias:
Serra de arco para metais
Limas (lima de mão)
Torno de bancada
Serra tico-tico
Serra de mesa
Berbequim sem fios
Jogo de brocas
Conjunto de brocas de pá
Conjunto de chaves de fendas11
11
The build in 3D
The build in 3D
FreeCAD model of this build, the bucket cut open: the propeller blades J on the shaft, the floating breaker H in its three grooves, the breaks K, the water tube L held by the faucet M, the cover P, the cross piece N with its fingers O, and the crank and gearing.
12
12
Churn
Churn
Pour about 6 litres of heavy cream into the bucket and set the breaker in its grooves; it floats on the cream. Pour warm or cold water from the kettle or tap into the tube L to bring the cream to about 15 °C, checked with the thermometer. Put on the cover, cross piece and gearing, and turn the crank steadily, timing it. When the butter comes, draw the buttermilk off at the faucet into a bowl, lift out the gearing, cover, breaker and butter, wash the butter in cold water until it runs clear, salt and weigh it.
Materiais para este passo:
Natas para bater6 l
Água1 peça
Sal marinho grosso1 peçaFerramentas necessárias:
Chaleira elétrica
Termómetro de sonda permanente
Cronómetro
Balança digital de cozinha
Taça grande de aço inoxidável13
13
Troubleshooting
Troubleshooting
Floating-breaker churn troubleshooting.
Flow
Loading...
14
14
History and honest limits
History and honest limits
**Edward Lynch** of Buffalo, New York, US 27,864, 10 April 1860, "Churn", assigned to himself and Jas. J. McCool. He claimed the floating breaker with its ring, bevelled arms and grooves, and the tube held by the faucet. His tube is metal; ours is printed, and our faucet draws the milk through a collar under the tube's foot, our reading of his double-duty faucet. Every size here is ours.
Materiais
16- 1 peçaReferência
- 2 peçasReferência
- 32 peçasReferência
- 1 peçaReferência
- 1 peçaReferência
- 1 peçaReferência
- 2 peçasReferência
- 1 peçaReferência
- 2 peçasReferência
- 1 peçaReferência
- 1 peçaReferência
- 2 peçasReferência
- 1 peçaReferência
- Referência
- 1 peçaReferência
- 1 peçaReferência
Ferramentas necessárias
20- Referência
- 1 vendor sell this, none ship to you yetReferência
- Referência
- 1 vendor sell this, none ship to you yetReferência
- Referência
- Referência
- Referência
- 1 vendor sell this, none ship to you yetReferência
- Referência
- Referência
- Referência
- Referência
- Referência
- 1 vendor sell this, none ship to you yetReferência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
Ficheiros de design
5Blueprints relacionados
Estes blueprints compartilham conhecimento — técnicas, materiais ou princípios

False-Bottom Jet Churn: Paddles Under a Pierced Partition Draw Cream Down at the Centre and Jet It Up at the Rim
por Buttercup
Marcenaria
11
0
0
0
0
0

Hot-Water Cylinder Churn: Cream Is Crushed Between a Warm Turning Cylinder and an Adjustable Plate, Then Falls to a Dasher
por Buttercup
Marcenaria
5
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
por TheChef
ARTESANATO
63
0
0
0
0
0
CC0 Domínio Público
Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.
Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

