Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Hung-Dasher Churn: The Dasher Hangs in a Long Hinged Journal Box Above the Lid, No Step in the Tub
Buttercup

Criado por

Buttercup

11. novembro 2026IE
4
0
0
0
0

Hung-Dasher Churn: The Dasher Hangs in a Long Hinged Journal Box Above the Lid, No Step in the Tub

Jehu Mitchell of Aleppo township, Pennsylvania, received US 27,927, dated 17 April 1860, for a churn. The dasher hangs from above in a long journal box on a standard fixed to the lid, with no step or metal bearing in the tub, whose "oxidation ... imparts a bad flavor to the butter". One half of the box is a cap hinged at one side: lift out half the lid, unhook the cap and the dasher comes out with the gearing left in place. The patent gives no sizes; every size here is ours.
Intermediário
About 2 days, plus printing

Instruções

1

Held from above

A carregar o notebook Jupyter…
2

A crank-turned upright dasher, one week before

Lynch's shaft stands in a step on the bottom. Mitchell hangs his from above, with nothing in the tub.
3

Read US 27,927

"Suspending the dasher within an elongated hinged journal box in the manner described, combined the following advantages. A rigid bearing is afforded to the dasher so as to prevent any tremulous motion, without the necessity of any metallic step or bearing within the churn, the oxidation of which imparts a bad flavor to the butter."
4

Print the driving wheel E

Crown wheel, 36 teeth on its face, module 2, with a hub; bored 12.4 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Arquivo de designSTLCC0 - Free
5

Print the pinion M

Spur pinion, 12 teeth, module 2, with a hub; bored 12.4 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
Arquivo de designSTLCC0 - Free
6

Lid B and C, brakes O

Cut a hardwood lid 15 mm thick to sit on the bucket's rim and saw it in two across the middle: part C carries the standard, part B lifts out. Cut a 28 mm half-hole in the middle of the cut edge for the shaft and a 30 mm hole in B to look in. Screw three hardwood brakes O, 30 mm deep and 245 tall, to the bucket's side a third of a turn apart, and seal the screw holes outside with silicone.

Materiais para este passo:

Balde de 20 litrosBalde de 20 litros1 peça
Tábua de madeira de leiTábua de madeira de lei2 peças
Parafusos para madeiraParafusos para madeira6 peças
Vedante de siliconeVedante de silicone1 peça

Ferramentas necessárias:

Serra tico-ticoSerra tico-tico
Serra de mesaSerra de mesa
Conjunto de brocas de páConjunto de brocas de pá
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Conjunto de chaves de fendasConjunto de chaves de fendas
Fita métricaFita métrica
7

Standard D, journal box and cap G

Glue up a hardwood standard 60 mm wide and 66 deep, 111 mm tall above the lid, with its back 22 mm rising to 217 mm and bored 12.6 mm across near the top for the wheel's axle. Mortise it into lid part C behind the shaft's hole. Cut a cap G 60 x 30 mm, 111 tall, and bore a 25.2 mm hole down the joint between standard and cap, half in each. Hang the cap on a butt hinge at one side and fit a hook H and eye I on the other.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei1 peça
Cola de madeiraCola de madeira1 peça
Dobradiça de livro para móvelDobradiça de livro para móvel1 peça
Colchete (macho e fêmea)Colchete (macho e fêmea)1 peça
Parafusos para madeiraParafusos para madeira4 peças

Ferramentas necessárias:

Serra de mesaSerra de mesa
Conjunto de formões para madeiraConjunto de formões para madeira
Sargento de barraSargento de barra
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Conjunto de brocas de páConjunto de brocas de pá
Conjunto de chaves de fendasConjunto de chaves de fendas
8

Dasher J with wings N and collars K and L

Cut a 25 mm hardwood dowel 485 mm long and glue a 12 mm stainless spindle into its top, standing 56 mm out. Glue two hardwood wings 200 x 60 x 20 mm across it, 20 and 140 mm above its foot, each bored with two 24 mm holes. Fit a hardwood collar L 44 mm across just below the lid, and a collar K 40 mm across on the spindle resting on the box's top. Set the shaft in the box, close the cap, and key the pinion M on the spindle above K.

Materiais para este passo:

Cavilhas de madeira duraCavilhas de madeira dura2 peças
Tábua de madeira de leiTábua de madeira de lei1 peça
Varão de aço inoxidávelVarão de aço inoxidável1 peça
Cola de madeiraCola de madeira1 peça
Bloco de madeira duraBloco de madeira dura1 peça
Shaft CollarShaft Collar1 peça
Filamento PETGFilamento PETG1 peça

Ferramentas necessárias:

Impressora 3D de filamento (FDM)Impressora 3D de filamento (FDM)
Serra de mesaSerra de mesa
Conjunto de brocas de páConjunto de brocas de pá
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Serra de arco para metaisSerra de arco para metais
Limas (lima de mão)Limas (lima de mão)
LixaLixa
9

Driving wheel E and crank

Pass a 12 mm stainless axle through the standard's back, fit the wheel E on it meshing the pinion, and a hardwood crank with a dowel handle on the other end; hold it with a collar and split pin.

Materiais para este passo:

Varão de aço inoxidávelVarão de aço inoxidável1 peça
Tábua de madeira de leiTábua de madeira de lei1 peça
Cavilhas de madeira duraCavilhas de madeira dura1 peça
Cola de madeiraCola de madeira1 peça
Shaft CollarShaft Collar1 peça
ContrapinoContrapino1 peça

Ferramentas necessárias:

Serra de arco para metaisSerra de arco para metais
Limas (lima de mão)Limas (lima de mão)
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Torno de bancadaTorno de bancada
10

The build in 3D

FreeCAD model of this build, the bucket cut open: the dasher J with its two wings hanging from the journal box, the brakes O, the lid, the standard D with its hinged cap G, hook and eye, and the wheel E with pinion M.
Arquivo de designBLENDCC0 - Free
11

Churn

Pour about 8 litres of heavy cream at about 15 °C, checked with the thermometer, into the bucket, set the lid and dasher in place, and turn the crank steadily, timing it. To look at the butter, lift out lid part B. When the butter comes, lift part B out, unhook the cap and take the dasher out, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

Materiais para este passo:

Natas para baterNatas para bater8 l
Sal marinho grossoSal marinho grosso1 peça
ÁguaÁgua1 peça

Ferramentas necessárias:

Termómetro de sonda permanenteTermómetro de sonda permanente
CronómetroCronómetro
Balança digital de cozinhaBalança digital de cozinha
Taça grande de aço inoxidávelTaça grande de aço inoxidável
12

Troubleshooting

Hung-dasher churn troubleshooting.

Flow

Loading...
13

History and honest limits

**Jehu Mitchell** of Aleppo township, Greene County, Pennsylvania, US 27,927, 17 April 1860, "Churn". He did not claim a churn without a bottom step nor a hinged bearing alone, but the gearing, standard, hinged cap, dasher and collar together. His journal box runs higher; ours stops below the crown wheel. His wings and brakes are "of common construction"; our two wings and three brakes, and every size, are ours.

Materiais

16

Ferramentas necessárias

18

Ficheiros de design

3

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...