Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Crank-and-Link Double-Dasher Churn: Two Dashers' Cranks Joined by a Curved Link, One Lever Turns or Rocks Both
Buttercup

Criado por

Buttercup

12. novembro 2026IE
7
0
0
0
0

Crank-and-Link Double-Dasher Churn: Two Dashers' Cranks Joined by a Curved Link, One Lever Turns or Rocks Both

Robert Parker of North Cohocton, New York, received US 33,213, dated 3 September 1861, for working two upright wing dashers in an oval churn with one lever. A cap that hooks onto ears on the box carries a horizontal crank over each dasher, coupled to its shaft. A curved link joins the two crank pins and the lever is pivoted to its middle: moving the lever's end round turns both dashers together, pushing it straight to and fro rocks them, and the user can work it from the front or the side. Unhook the cap and the whole mechanism lifts off. The patent gives no sizes; every size here is ours.
Intermediário
About 2 days

Instruções

1

Turning or rocking with one lever

A carregar o notebook Jupyter…
2

A mechanism that lifts off the churn as one, four months before

Stilwell swings his driving arm back on a frame. Parker's whole drive is in a cap that hooks onto ears and lifts off.
3

Read US 33,213

"The object of my invention is to so arrange the mechanism that by a rectilinear movement of the operator either a vibratory or rotary motion may be given to the dashers."
4

Oval box A, cover, cups and ears C

Make an oval box A whose inside is two 90 mm half rounds 140 mm apart joined by straight sides, 300 deep: a hardwood floor and two straight hardwood sides, with 1.5 mm stainless sheet bent round the ends in grooves, all sealed with silicone. Seal a printed cup for each dasher's foot on the floor at the half rounds' centres. Cut an HDPE cover to the outside with a 27 mm hole over each cup. Screw a hardwood ear C 30 x 60 mm, 140 long, to each end, standing above the box, with a mortise c 24 mm wide and 20 deep near its top.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei3 peças
Chapa de aço inoxidávelChapa de aço inoxidável1 peça
Vedante de siliconeVedante de silicone1 peça
Cola de madeiraCola de madeira1 peça
Parafusos para madeiraParafusos para madeira24 peças
Filamento PETGFilamento PETG1 peça
Chapa de PEADChapa de PEAD1 peça

Ferramentas necessárias:

Impressora 3D de filamento (FDM)Impressora 3D de filamento (FDM)
Serra de mesaSerra de mesa
Serra tico-ticoSerra tico-tico
BússolaBússola
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Sargento de barraSargento de barra
Conjunto de chaves de fendasConjunto de chaves de fendas
5

Print the cups (two)

A cup for a dasher's foot: 44 mm across, 14 high, a 26 mm socket 10 deep. Print two. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Arquivo de designSTLCC0 - Free
6

Wing dashers B and shafts a

Turn two hardwood dasher shafts 25 mm across, 320 long, and set a 16 mm stainless rod 80 mm long 20 mm into each top, with a flat filed on its end as the tenon of the coupling f. Mortise four hardwood wings 120 x 120 x 12 mm through each, two crossed at 35 to 155 mm up and two crossed at 160 to 280, turned 45 degrees from the lower pair.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei1 peça
Varão de aço inoxidávelVarão de aço inoxidável2 peças
Cola de madeiraCola de madeira1 peça
Cavilhas de madeira duraCavilhas de madeira dura1 peça

Ferramentas necessárias:

Torno de madeiraTorno de madeira
Serra de mesaSerra de mesa
Conjunto de formões para madeiraConjunto de formões para madeira
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Limas (lima de mão)Limas (lima de mão)
7

Cap D, cranks e, link o and lever h

Glue up a hardwood cap D 400 x 120 x 60 mm, cut a recess d 260 x 100 mm, 42 deep, in its underside, and a slot through its front wall for the lever. Glue a tenon b 24 x 20 mm on each end to drop into the ears' mortises, and fit a hook and eye at each end to hold it. Bore it 16.6 mm through over each dasher. Make each crank e of a 16 mm stainless shaft through the cap with a slot in its foot to take the dasher's tenon (the coupling f), and a mild steel flat bar arm, 35 mm throw, with an 8 mm pin. Bend a 6 mm steel rod into a half round joining the two pins, eyes at its ends, and fix a pivot eye at its middle. Pivot a hardwood lever h, 500 long with a handle, on the eye so it comes out through the cap's slot.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei2 peças
Cola de madeiraCola de madeira1 peça
Colchete (macho e fêmea)Colchete (macho e fêmea)2 peças
Varão de aço inoxidávelVarão de aço inoxidável1 peça
Barra chata de aço macioBarra chata de aço macio1 peça
Barra redonda de aço macioBarra redonda de aço macio1 peça
Sortido de parafusos sextavadosSortido de parafusos sextavados3 peças
Porca de segurança com anel de nylonPorca de segurança com anel de nylon3 peças
ContrapinoContrapino2 peças

Ferramentas necessárias:

Serra de mesaSerra de mesa
Conjunto de formões para madeiraConjunto de formões para madeira
TupiaTupia
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Serra de arco para metaisSerra de arco para metais
Limas (lima de mão)Limas (lima de mão)
Torno de bancadaTorno de bancada
Conjunto de chaves de fendasConjunto de chaves de fendas
8

The build in 3D

FreeCAD model of this build, half the box cut away: the oval box with its cups and ears, the two wing dashers, the cap hooked onto the ears with the two cranks, the curved link and the lever coming out of its slot.
Arquivo de designBLENDCC0 - Free
9

Churn

Stand the dashers in their cups, pour about 12 litres of heavy cream at about 15 °C, checked with the thermometer, into the box, put on the cover over the shafts, and lower the cap so the cranks' slots take the dashers' tenons and its tenons drop into the ears; hook it. Move the lever's end round in a small circle to turn the dashers, or push it straight to and fro to rock them, timing it. When the butter comes, unhook and lift off the cap, lift out the dashers, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

Materiais para este passo:

Natas para baterNatas para bater12 l
Sal marinho grossoSal marinho grosso1 peça
ÁguaÁgua1 peça

Ferramentas necessárias:

Termómetro de sonda permanenteTermómetro de sonda permanente
CronómetroCronómetro
Balança digital de cozinhaBalança digital de cozinha
Taça grande de aço inoxidávelTaça grande de aço inoxidável
10

Troubleshooting

Crank-link churn troubleshooting.

Flow

Loading...
11

History and honest limits

**Robert Parker** of North Cohocton, Steuben County, New York, US 33,213, 3 September 1861, "Improved Churn". He claimed "the combination of the cranks, the curved link, and the operating-lever". His box was oval and staved; ours has straight sides and stainless ends. He does not describe the dashers beyond "wing-dashers"; ours follow his Fig. 1. The patent gives no sizes; every size here is ours.

Materiais

18

Ferramentas necessárias

18

Ficheiros de design

2

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...