Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL

Oblique Perforated-Dasher Churn: A Slanted Spindle Drives the Cream Down and Sideways, a Guard Turns It Back
E. N. Sprinkle of Marion, Virginia, received US 25,985, dated 1 November 1859, for a churn. Three perforated dashers turn on a spindle set slantwise across the churn, from a standard low on one side to a slot in the rim on the other, and a crank on its end turns it fast. The cream is driven down and towards one side and cut by the holes' edges; a sloping guard under the dashers sends it back up to them, and the bottom stays clear for gathering the butter.
The patent gives no sizes; every size here is ours.
Iniciante
About a day, plus printing
Instruções
1
1
The spindle's slope, and where the cream goes
The spindle's slope, and where the cream goes
A carregar o notebook Jupyter…
2
2
A turning dasher with curved wings, seven weeks before
A turning dasher with curved wings, seven weeks before
Hassler's dasher stands upright. Sprinkle tilts his spindle so the dashers drive the cream sideways too.
3
3
Read US 25,985
Read US 25,985
"By reason of the dashers being operated in an oblique position, it will be seen that the cream will not only be forced down but will also be forced toward the side of the churn which supports the upper end of the dasher shaft, and is thus not only effectually agitated by the motion of the dashers, but is also cut and stirred by the edges of the perforations c, c, c, in the dashers"
4
4
Print the dashers C
Print the dashers C
Three perforated half-ellipse blades, 210 x 80 mm and 4 mm thick, round a 24 mm tube bored 12.6 mm, with a cross hole for a pin. Print with supports. PETG, 0.2 mm layers, 40 % infill, 4 walls.
5
5
Print the standard f
Print the standard f
A post 30 mm square and 178 mm tall on a 60 mm base with an M6 nut trap, its top bored 12.8 mm at 38 degrees for the spindle's lower end, e. PETG, 0.2 mm layers, 40 % infill, 4 walls.
6
6
Print the guard's leg
Print the guard's leg
A leg 24 mm across and 92 mm tall on a 50 mm foot, to hold the guard's low end. PETG, 0.2 mm layers, 40 % infill, 4 walls.
7
7
Standard f, guard F and slot h
Standard f, guard F and slot h
Drill a 6.5 mm hole in the bucket's floor 115 mm from its centre. Push an M6 nut into the standard's trap, lay an O-ring under its base and bolt it over the hole from underneath, its sloping bore facing across the bucket. Cut the guard F from 8 mm hardwood: a half-circle to fit the bucket 110 mm up, notched round the standard. Screw it to the standard's side 125 mm up and onto its leg, 95 mm up at the far end, on one side of the spindle's line. Cut a slot 13 mm wide and 12 mm deep in the rim opposite the standard, and screw an eye h' beside it.
Materiais para este passo:
Balde de 20 litros1 peça
Sortido de parafusos sextavados1 peça
Porca sextavada1 peça
Anilha plana1 peça
O-ring1 peça
Tábua de madeira de lei1 peça
Parafusos para madeira4 peças
Colchete (macho e fêmea)1 peça
Filamento PETG1 peçaFerramentas necessárias:
Impressora 3D de filamento (FDM)
Berbequim sem fios
Jogo de brocas
Serra tico-tico
Bússola
Serra de arco para metais
Limas (lima de mão)
Chave inglesa ajustável
Conjunto de chaves de fendas8
8
Spindle D and crank E
Spindle D and crank E
Cut 12 mm stainless rod 625 mm long. Heat 415 mm from one end with the torch and bend it at right angles, then 120 mm further on bend it back parallel to make the crank. Slide the dasher onto the straight part and pin it 70 mm from the end. Set the end into the standard's bore and lay the spindle in the slot, then hook the catch g over it into the eye.
Materiais para este passo:
Varão de aço inoxidável1 peçaFerramentas necessárias:
Maçarico a propano
Torno de bancada
Martelo
Luvas resistentes ao calor
Serra de arco para metais
Limas (lima de mão)
Berbequim sem fios
Jogo de brocas9
9
Cover B
Cover B
Cut a hardwood cover to sit on the rim, with a notch for the spindle at the slot, a 10 mm vent hole j, and a screw eye in the middle with a ring of stainless wire for lifting, i.
Materiais para este passo:
Tábua de madeira de lei1 peça
Olhal de rosca1 peça
Arame de aço inoxidável1 peçaFerramentas necessárias:
Serra tico-tico
Bússola
Berbequim sem fios
Jogo de brocas
Lixa10
10
The build in 3D
The build in 3D
FreeCAD model of this build, the bucket and cover cut through the middle: the standard, the slanting spindle with its crank, the three-bladed dasher, and the guard on its leg. The dasher was turned through 24 angles.
11
11
Churn
Churn
Pour about 6 litres of heavy cream at about 15 °C into the bucket, checked with the thermometer, and put the cover on. Turn the crank fast and steadily, timing it. When the butter comes, unhook the catch, lift the spindle and dasher out, gather the butter from the clear bottom, drain the buttermilk, wash the butter in cold water until it runs clear, salt and weigh it.
Materiais para este passo:
Natas para bater6 l
Sal marinho grosso1 peça
Água1 peçaFerramentas necessárias:
Termómetro de sonda permanente
Cronómetro
Balança digital de cozinha
Taça grande de aço inoxidável12
12
Troubleshooting
Troubleshooting
Oblique dasher churn troubleshooting.
Flow
Loading...
13
13
History and honest limits
History and honest limits
**E. N. Sprinkle** of Marion, Smyth County, Virginia, US 25,985, 1 November 1859, "Churn". He claimed, as an improvement on the churn patented to Hatfield and Goldsmith on 13 July 1858, "the combination of the perforated obliquely arranged dashers C, C, C, with the single inclined stationary guard F". The patent gives no sizes; every size here is ours. His cover is conical; ours is flat.
Materiais
15- 1 peçaReferência
- Referência
- 1 peçaReferência
- 1 peçaReferência
- 1 peçaReferência
- 1 peçaReferência
- 4 peçasReferência
- 1 peçaReferência
- 1 peçaReferência
- 1 peçaReferência
- 1 peçaReferência
- 1 peçaReferência
- Referência
- 1 peçaReferência
- 1 peçaReferência
Ferramentas necessárias
18- Referência
- 1 vendor sell this, none ship to you yetReferência
- Referência
- 1 vendor sell this, none ship to you yetReferência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
Ficheiros de design
4Blueprints relacionados
Estes blueprints compartilham conhecimento — técnicas, materiais ou princípios

Hinged-Leaf Wing Dasher Churn: Turn One Way to Churn, Reverse and a Leaf Opens to Gather the Butter
por Buttercup
Marcenaria
6
0
0
0
0
0

Hooked Breaker-Frame Churn: Breakers Held Still From the Lid, Then Hooked to the Dasher to Gather
por Buttercup
COMIDA E BEBIDAS
4
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
por TheChef
ARTESANATO
63
0
0
0
0
0
CC0 Domínio Público
Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.
Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

