Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Stovetop Kettle: a Square Copper Kettle (Hasluck, 1907)
Forge

Criado por

Forge

4. novembro 2026NO
10
0
0
0
0

Stovetop Kettle: a Square Copper Kettle (Hasluck, 1907)

A tinsmith's square kettle in sheet copper, 9 x 9 in and 3 5/8 in deep: a box body with folded corner seams, a hollowed top pened on, a brazed and bent spout, a small cover, and a wooden handle on brass uprights. Hasluck prefers copper; tinplate also works and is a separate route. Source: Paul N. Hasluck, Tinplate Work (1907), pp. 91-98. Unknown: copper gauge, solder. Picture: Figs. 188-189 of the book.
Avançado
Unknown

Instruções

1

Cut the patterns

For a body 9 x 9 x 3 5/8 in, cut two ends 9 1/2 x 4 in and two sides 9 1/4 x 4 in, notched for box seams at the corners (Figs. 190-191), with allowances to fold at top and bottom. Punch the spout hole in the front. Cut the bottom 9 1/2 in square, notched for a 1/4 in edge. Set out the top as a 10 1/2 in square with curved allowances for hollowing and a 4 in circle for the cover hole (Fig. 193); set out the spout from the elevation (Fig. 192), the cover and its cone-shaped rim (Figs. 194-195).

Materiais para este passo:

Chapa de cobreChapa de cobre1 body, bottom, top, spout, cover

Ferramentas necessárias:

Compasso de pontasCompasso de pontas
Ponta de traçarPonta de traçar
Tesoura de chapaTesoura de chapa
2

Braze and shape the spout

Thin the long edges by hammering. Set in the throat with a stretching hammer on a beak iron, bend the spout round until the edges overlap, bind it with wire, lay spelter and borax along the inside of the seam and braze it; then close and braze the under seam. Fill it with lead and bend the neck with a round-faced hammer on the hollowing block; file off spare spelter and smooth it. Run out the lead, throw off a seating round the large end, trim the top with snips and tin the inside.

Materiais para este passo:

Metal desconhecidoMetal desconhecido1 spelter
EstanhoEstanho1 tinning

Ferramentas necessárias:

Martelo de aplanarMartelo de aplanar
EstacaEstaca
Arame de ferroArame de ferro
Bórax em póBórax em pó
Maçarico de brasagemMaçarico de brasagem
ChumboChumbo
Escumadeira perfuradaEscumadeira perfurada
Bloco de madeira duraBloco de madeira dura
Lima para metalLima para metal
Tesoura de chapaTesoura de chapa
3

Fold and seam the body

Fold the top edges square, the front and back outwards and the sides likewise; fold the bottom edges right over inwards to take the bottom (Fig. 188). Hook each side's end over the front's and work the corner seam on a straight-edged tool (Figs. 198-199). Turn up the bottom's 1/4 in edge, push it edge-down into the bottom folds, and solder the bottom and seams.

Materiais para este passo:

Solda de estanho-chumboSolda de estanho-chumbo1 peça

Ferramentas necessárias:

Maço de madeiraMaço de madeira
EstacaEstaca
Ferro de solda elétricoFerro de solda elétrico
FluxoFluxo
4

Hollow the top and make the cover

Hollow the top on the block: sink the four sides a little, hollow the corners with a bullet-faced hammer, flatten each side along the block edge, even the shoulder and smooth it all over. Pare the edges, mark the flange with an edging machine, set it down square with a hatchet stake and mallet, and take up an edge to fit over the body. Cut the cover hole with circular snips and fit a narrow wired rim, worked over inside. Make the cover: solder its cone rim to fit the wired rim, throw off a flange, hollow the cover disc and seam it on, and fix the knob.

Materiais para este passo:

Arame de ferroArame de ferro1 rim
Solda de estanho-chumboSolda de estanho-chumbo1 peça
Metal desconhecidoMetal desconhecido1 cover knob

Ferramentas necessárias:

Martelo de aplanarMartelo de aplanar
Bloco de madeira duraBloco de madeira dura
EstacaEstaca
Maço de madeiraMaço de madeira
Tesoura de chapaTesoura de chapa
Ferro de solda elétricoFerro de solda elétrico
FluxoFluxo
5

Handle, top and spout

Cut two handle uprights from stout brass or copper band (Fig. 196), drill them for rivets and for the spindle that carries the wooden handle, and bend them to shape. Rivet them to the top and solder over the rivet heads inside. Pene the top down onto the body and solder along each edge. Push the spout through its hole from inside until its large end butts against the front, and solder it strongly from inside.

Materiais para este passo:

Chapa de latãoChapa de latão1 handle uprights
Varão de latãoVarão de latão1 spindle
CaboCabo1 wood
Rebites de cobreRebites de cobre1 number not given
Solda de estanho-chumboSolda de estanho-chumbo1 peça

Ferramentas necessárias:

Berbequim de mãoBerbequim de mão
Martelo de rebitarMartelo de rebitar
Maço de madeiraMaço de madeira
Ferro de solda elétricoFerro de solda elétrico
FluxoFluxo

Materiais

9

Ferramentas necessárias

17

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...