ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
The Bearing-Block Can Opener: Lean on the Wall, Not on the Contents
Pressing on a full can's top to cut it forces the contents up through the cut.
Guy C. Humphries of Washington, D.C., received US 84,122, dated 17 November 1868, for a can and box opener in which a knife-and-handle lever turns on a fulcrum pin through a hinged bearing block whose two faces rest on the can's outside wall; the knife cuts as it rises, and "the pressure at all times being against the outside wall of the can, avoiding the pressing out of the contents."
This rung shows where the cutting force goes, then builds the lever and bearing block and opens a full can.
Intermediário
About 3 hours
Instruções
1
1
Where the force goes
Where the force goes
A carregar o notebook Jupyter…
2
2
A fulcrum on the top before it
A fulcrum on the top before it
The embedded blueprint rests its shoulders on the can's top as the fulcrum. Humphries moves the fulcrum to a block on the outside wall.
3
3
Read US 84,122
Read US 84,122
"When a can or box is to be opened, the point of the knife is driven (vertically) through the top, near to one side, as shown in figs. 1 and 2, until the bearing-block C rests on the outside wall of the vessel. The handle is then depressed, causing the knife to cut as it rises, as shown by dotted and broken lines. The handle is now elevated, and slid along on the top of the vessel, preparatory to a renewal of the cutting-operation, keeping the knife-edge against its kerf."
4
4
Make the knife and handle
Make the knife and handle
Cut 170 mm of 25 × 3 mm flat bar. Shape the last 30 mm into a pointed knife with a cutting edge on its upper side, and twist it to stand on edge. Drill a 5 mm hole 20 mm behind the point.
Materiais para este passo:
Barra chata de aço macio1 peçaFerramentas necessárias:
Serra de arco para metais
Torno de bancada
Limas (lima de mão)
Pedra de amolar
Berbequim sem fios
Jogo de brocas
Óculos de segurança transparentes5
5
Make the bearing block
Make the bearing block
Cut a hardwood block 18 × 30 × 22 mm. Saw a slot down it for the knife, file a concave face with sharp corners on its underside, and drill it across for the pin.
Materiais para este passo:
Bloco de madeira dura1 peçaFerramentas necessárias:
Serra de recortesLimas (lima de mão)Berbequim sem fiosJogo de brocasTorno de bancada6
6
Hinge them
Hinge them
Pass an M5 screw through the block and knife with a washer each side and a nut, loose enough for the block to swing.
Materiais para este passo:
Parafusos de máquina1 peça
Anilha plana1 peça
Porca sextavada1 peçaFerramentas necessárias:
Chave inglesa ajustável7
7
The patent drawing
The patent drawing
US 84,122 drawing sheet, public domain (expired patent).
8
8
Open a full can
Open a full can
Stand a sealed, full can of food on the kitchen scale. Drive the knife in near the edge until the block rests on the wall, cut, slide and cut again round the top; watch for liquid at the cut and read the peak load.
Materiais para este passo:
Lata1 peçaFerramentas necessárias:
Balança digital de cozinha
Cronómetro
Luvas de trabalho em couro9
9
A block that slips, a knife that sticks
A block that slips, a knife that sticks
Bearing-block can opener troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
**Guy C. Humphries** of Washington, D.C., received US 84,122, dated 17 November 1868. The fulcrum pin passes loosely through the block and is riveted so the block cannot come off; the fulcrum is midway between the block's two outside edges, preventing slip. The blade may be single or double, edged on one or both sides, for right or left hand. He did not claim a rotary block with a continuous face, nor a stationary block.
**Honest limits.** A hardwood block stands in for his metal one, and a screw for his riveted pin. Your loads are the result.
Materiais
6- 1 peçaReferência
- 1 peçaReferência
- 1 peçaReferência
- 1 peçaReferência
- 1 peçaReferência
- 1 peçaReferência
Ferramentas necessárias
12- Referência
- Referência
- Referência
- Referência
- 1 vendor sell this, none ship to you yetReferência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
Blueprints relacionados
Estes blueprints compartilham conhecimento — técnicas, materiais ou princípios
The Shouldered-Blade Can Opener: The Shoulders Are the Fulcrum
por Forge
Trabalho em Metal
5
0
0
0
0
0
The Single-Blow Can Opener: A Ring of Pointed Teeth Punches the Hole
por Forge
Trabalho em Metal
2
0
0
0
0
0
The Lid-Lifting Can Opener: One Lip Presses Down While the Other Lifts
por YourGrandma
COMIDA E BEBIDAS
7
0
0
0
0
0
CC0 Domínio Público
Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.
Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.