Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL

Adjustable-Board Churn: A Perforated Board on a Pin Beside the Wall Is Set to Break the Cream or Gather the Butter
George H. Van Vleck of Buffalo, New York, received US 28,219, dated 8 May 1860, for a churn. Wings near the foot of an upright crank-driven staff swirl the cream; beside the wall stands a perforated board on its own pin, held at the angle wanted by pins in the bottom. Set one way it breaks the globules as the cream is forced against it; set the other it gathers the butter between it and the side. Its foot is cut away so the wings pass under it.
The patent gives no sizes; every size here is ours.
Intermediário
About 2 days, plus printing
Instruções
1
1
Two settings of one board
Two settings of one board
A carregar o notebook Jupyter…
2
2
An upright crank churn, three weeks before
An upright crank churn, three weeks before
Mitchell's breaks are fixed to the wall. Van Vleck's board turns on a pin and is set to the work.
3
3
Read US 28,219
Read US 28,219
"The board may be placed so as to set at any desired angle, either for gathering the butter between it and the sides of the churn, or for breaking the globules, when the cream is forced against it. As the board is changed so the openings or perforations are changed and their edges and sides are presented differently for assisting in breaking the globules which contain the butter of the cream."
4
4
Print the toothed wheel F
Print the toothed wheel F
Crown wheel, 36 teeth on its face, module 2, with a hub; bored 12.4 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
5
5
Print the pinion E
Print the pinion E
Spur pinion, 12 teeth, module 2, with a hub; bored 12.4 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
6
6
Board C, shaft d, socket and guide d'
Board C, shaft d, socket and guide d'
Cut a hardwood board 15 mm thick, 95 wide and 297 tall. Leave its outer 15 mm full height and a foot 40 mm long and 17 high at the bottom; cut the rest away between 20 and 62 mm up so the wings pass under. Bore eight 14 mm holes x in two rows in its face, and glue a 10 mm stainless shaft d along its outer edge, standing 45 mm above it. Screw a hardwood socket block bored 10.6 mm, 8 deep, to the bucket's floor 122 mm from the centre, and a hardwood guide d' bored 10.6 mm inside the wall above it, 325 mm up.
Materiais para este passo:
Tábua de madeira de lei1 peça
Varão de aço inoxidável1 peça
Cola de madeira1 peça
Bloco de madeira dura1 peça
Parafusos para madeira4 peçasFerramentas necessárias:
Serra de mesa
Serra tico-tico
Berbequim sem fios
Jogo de brocas
Conjunto de brocas de pá
Lixa
Conjunto de chaves de fendas7
7
Pins a
Pins a
Glue three 10 mm dowel pins 20 mm tall into the floor on a circle 35 mm round the socket, toward the centre and 50 degrees apart, so the board's foot drops between the middle pin and either outer one: 25 degrees one way to break, 25 degrees the other to gather.
Materiais para este passo:
Cavilhas de madeira dura1 peça
Cola de madeira1 peçaFerramentas necessárias:
Transferidor
Berbequim sem fios
Jogo de brocas
Serra de arco para metais8
8
Staff B, wings D, cross piece H and gearing
Staff B, wings D, cross piece H and gearing
Screw a hardwood step 50 x 50 x 8 mm to the floor's centre, bored 12.6 mm, 6 deep. Cut a 25 mm hardwood staff 348 mm long, glue 12 mm stainless spindles into its ends, and fix a hardwood wing 170 x 30 x 15 mm across it 25 mm above the floor. Cut a hardwood cross piece H 350 x 205 x 25 mm to sit on the rim, bored 13 mm over the centre as the guide I; fit the pinion on the staff's top, two chairs with a 12 mm crank shaft and the wheel F, and a hardwood crank with a dowel handle.
Materiais para este passo:
Bloco de madeira dura1 peça
Cavilhas de madeira dura2 peças
Varão de aço inoxidável2 peças
Tábua de madeira de lei2 peças
Cola de madeira1 peça
Parafusos para madeira10 peças
Shaft Collar2 peças
Contrapino1 peça
Filamento PETG1 peçaFerramentas necessárias:
Impressora 3D de filamento (FDM)
Serra de mesa
Serra de arco para metais
Limas (lima de mão)
Torno de bancada
Berbequim sem fios
Jogo de brocas
Conjunto de brocas de pá
Sargento de barra9
9
The build in 3D
The build in 3D
FreeCAD model of this build, the bucket cut open: the staff with its wings, the perforated board on its shaft set at 25 degrees between two pins, the guide d', and the cross piece with the crank, wheel F and pinion E.
10
10
Churn
Churn
Set the board leaning against the swirl, its face meeting the cream, to break. Pour about 8 litres of heavy cream at about 15 °C, checked with the thermometer, into the bucket, put the cross piece and gearing on, and turn the crank steadily, timing it. When the butter comes, lift the board and drop it between the other pair of pins to gather, and turn slowly until the butter collects against the side. Lift off the gearing, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.
Materiais para este passo:
Natas para bater8 l
Sal marinho grosso1 peça
Água1 peçaFerramentas necessárias:
Termómetro de sonda permanente
Cronómetro
Balança digital de cozinha
Taça grande de aço inoxidável11
11
Troubleshooting
Troubleshooting
Adjustable-board churn troubleshooting.
Flow
Loading...
12
12
History and honest limits
History and honest limits
**George H. Van Vleck** of Buffalo, New York, US 28,219, 8 May 1860, "Churn". He claimed the box, the dasher and staff, and the adjustable hinged board with its pins and openings. He says the board can be set "at any desired angle"; our three pins give two settings, and which of them breaks best and which gathers best is for the maker to find and note. Every size here is ours, and our gears are printed.
Materiais
13- 2 peçasReferência
- 2 peçasReferência
- 3 peçasReferência
- 1 peçaReferência
- 14 peçasReferência
- 1 peçaReferência
- 2 peçasReferência
- 2 peçasReferência
- 1 peçaReferência
- 1 peçaReferência
- Referência
- 1 peçaReferência
- 1 peçaReferência
Ferramentas necessárias
17- 1 vendor sell this, none ship to you yetReferência
- 1 vendor sell this, none ship to you yetReferência
- 1 vendor sell this, none ship to you yetReferência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
Ficheiros de design
3Blueprints relacionados
Estes blueprints compartilham conhecimento — técnicas, materiais ou princípios

Hung-Dasher Churn: The Dasher Hangs in a Long Hinged Journal Box Above the Lid, No Step in the Tub
por Buttercup
Marcenaria
4
0
0
0
0
0

Leaning-Scoop Churn: Three Scoops Tilted 10, 5 and 0 Degrees Throw the Cream at Sharp-Topped Ribs and a Slit Cover
por Buttercup
Marcenaria
6
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
por TheChef
ARTESANATO
63
0
0
0
0
0
CC0 Domínio Público
Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.
Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

