Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Three-Legged Router: A T-Frame on the Table Beside the Work, Its Depth Set by a Knob While Cutting (Willard & Young, 1939)
Forge

Criado por

Forge

13. novembro 2026NO
6
0
0
0
0

Three-Legged Router: A T-Frame on the Table Beside the Work, Its Depth Set by a Knob While Cutting (Willard & Young, 1939)

Homer E. Willard and Frederick S. Young of Toledo, Ohio, received US 2,146,458, dated 7 February 1939, for a simple portable router with few moving parts. The motor sits in an open-fronted support in the middle of a T-shaped frame, so the bit and the work are always in view. The frame stands on three legs on the table beside the clamped work: two curved legs at one end, and at the other a screw with a knob. Turning the knob with one hand raises or lowers the bit while it cuts. We print the frame in PETG round a small DC motor. The sizes are ours.
Intermediário
About 1 day

Instruções

1

Depth by the knob

A carregar o notebook Jupyter…
2

Read US 2,146,458

"Thus, by turning the wrist in one direction or the other, the bit 19 may be raised or lowered, as required, without stopping the motor and without removing the hands from the tool."
3

Print the frame

The T-shaped frame 10: the motor support 13 with its ledge 14 (an 18 mm hole and two M4 holes 29 mm apart) and curved wall 15, open at the front 16; arm 11 to the cross with two curved legs 21, 22; arm 12 to a boss with an M10 nut trap for the screw leg 24. PETG, 0.2 mm layers, 40 % infill, 5 walls; print it legs up, ledge on the bed.
Arquivo de designSTLCC0 - Free
4

Fit the motor

Print the frame. Fit the collet adapter on the motor's shaft, stand the motor in the support with its face on the ledge and the collet through the hole, and screw it down with two M4 screws. Wire it through a toggle switch to the DC supply as for our 1924 router.

Materiais para este passo:

Filamento PETGFilamento PETG1 peça
Motor elétricoMotor elétrico1 peça
Adaptador de pinça para eixo de motorAdaptador de pinça para eixo de motor1 peça
Parafuso de cabeça cilíndrica com sextavado interiorParafuso de cabeça cilíndrica com sextavado interior2 peças
Interruptor de alavancaInterruptor de alavanca1 peça
Fio de ligaçãoFio de ligação1 peça
Manga termorretráctilManga termorretráctil1 peça

Ferramentas necessárias:

Impressora 3D de filamento (FDM)Impressora 3D de filamento (FDM)
Fonte de alimentação de corrente contínuaFonte de alimentação de corrente contínua
Ferro de solda elétricoFerro de solda elétrico
Jogo de chaves AllenJogo de chaves Allen
5

The screw leg and knob

Press an M10 nut into the trap under the boss. Cut 100 mm of M10 threaded rod, round its lower end with a file so it slides on the table, and screw it up through the nut. Turn a hardwood knob 25, bore it, and glue it on the rod's top with a nut locked under it.

Materiais para este passo:

Porca sextavadaPorca sextavada2 peças
Varão roscadoVarão roscado1 peça
Tábua de madeira de leiTábua de madeira de lei1 peça
Cola de madeiraCola de madeira1 peça

Ferramentas necessárias:

Serra de arco para metaisSerra de arco para metais
Jogo de limasJogo de limas
Torno de madeiraTorno de madeira
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Chave inglesa ajustávelChave inglesa ajustável
6

Rout

Clamp the work down on the table between two strips. Fit a bit and stand the router on the table so its legs are beside the work and the bit is over it. Turn the knob until the bit just clears the work, switch on, and turn it down a little while moving the router over the area to be cut, one hand on arm 11 and the other on the knob.

Ferramentas necessárias:

Conjunto de fresas de tupiaConjunto de fresas de tupia
Tábua de madeira de leiTábua de madeira de lei
Sargento de barraSargento de barra
Paquímetro digital de 6 polegadasPaquímetro digital de 6 polegadas
Óculos de segurançaÓculos de segurança
7

Troubleshooting

Three-legged router troubleshooting.

Flow

Loading...
8

History and honest limits

**Homer E. Willard** and **Frederick S. Young** of Toledo, Ohio, US 2,146,458, dated 7 February 1939, filed 11 December 1935. They claimed "a portable router comprising a T-shaped frame having a semi-circular recess in the stem of the T, a bit-operating motor mounted in said recess and a leg projecting in the same direction as the bit from each of the ends of the frame", one leg "screw-threaded through the arm and terminating above the arm in an operating knob". Their work was an electrotype clamped on the table; their motor ran on mains. Ours is a small DC motor in a printed frame. They give no sizes; every size here is ours.

Materiais

11

Ferramentas necessárias

15

Ficheiros de design

1

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...