アート
美容とウェルネス
工芸
文化と歴史
エンターテインメント
環境
食品と飲料
リバースエンジニアリング
科学
スポーツ
テクノロジー
ウェアラブル
Tubular Disk Dasher Churn: A Wide Shallow Churn That Rolls the Butter Into Balls
Francisco wanted a churn that both mixed air into the cream and gathered the separated butter "into large balls or rolls."
Samuel P. Francisco of Reading, Pennsylvania, received US 6,544, dated 19 June 1849, for an atmospheric churn: a wide and shallow tub with, near its bottom, a revolving disk nearly as large as the tub, "perforated with radial tubular channels" from its periphery to its centre, where they meet a tubular stem open at the top. The forward sides of the channels project, so in rapid motion "a partial vacuum is formed in the cream behind the projecting side of the channel into which the air rushes." Once the butter appears the disk is turned slowly, and the particles roll on its upper surface into balls.
This rung works out the speed the air needs, then prints the disk dasher in one piece, fits it in a wide shallow tub, and makes butter.
中級者
About 2 hours, plus printing
手順
1
1
Speed for the air
Speed for the air
Jupyter ノートブックを読み込み中…
2
2
Air drawn down a hollow stem before it
Air drawn down a hollow stem before it
The embedded blueprint draws air down a hollow shaft into two arms. Francisco spreads it through channels in a disk near the bottom of a shallow tub.
3
3
Read US 6,544
Read US 6,544
"At this point of the process, the motion of the dasher, before rapid, is reduced and moved around very slowly and gently, and the particles of the butter by abrasion upon its upper surface are brought into contact with, and cohere to each other, forming large balls or rolls."
4
4
Print the dasher
Print the dasher
Print the disk dasher flat in one piece, with supports in the channels: a 176 mm disk with six radial channels, their mouths' forward sides projecting, and a hollow stem with a cross hole for the handle bar. It needs a 200 mm bed. Blow down the stem to check each channel is clear. Print the step. Print in PETG at 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
このステップの材料:
PETGフィラメント1 個必要な工具:
FDM 3D プリンター5
5
Print the dasher
7
7
The tub
The tub
Take a wide, shallow food-safe container about 200 mm across and 90 mm deep, and bed the step in the centre of its floor with silicone.
このステップの材料:
食品級の保存容器1 個
シリコーンシーラント1 個必要な工具:
メジャー（巻尺）8
8
Handle
Handle
Stand the dasher's pivot in the step. Push a 12 mm hardwood dowel through the stem's cross hole as a handle bar, leaving the stem's top open for the air.
このステップの材料:
堅木のダボ1 個必要な工具:
手のこぎり
紙やすり9
9
The build in 3D
The build in 3D
FreeCAD model of this build, not of the patent: the shallow tub cut away to show the disk dasher in its step, the radial channels' projecting mouths at its rim, the hollow stem, and the handle bar.
10
10
Spin, then roll the butter
Spin, then roll the butter
Let the heavy cream stand until it reaches about 15 °C, checked with the thermometer. Pour in about 2 litres, enough to stand 40–50 mm above the disk and no more, as he said. Twist the bar back and forth as fast as you can and watch for bubbles; when the butter appears in fine grains, turn it slowly and gently so the grains roll into balls on the disk. Pour off the buttermilk, add cold water, churn a little and pour off again until it runs clear; work in a pinch of salt and weigh the butter.
このステップの材料:
生クリーム2000 ml
粗い海塩1 個
水1 個必要な工具:
差しっぱなしのプローブ温度計
ストップウォッチ
デジタルキッチンスケール
ステンレス鋼の大きな混ぜ鉢11
11
No bubbles, butter that will not ball
No bubbles, butter that will not ball
Tubular disk dasher churn troubleshooting.
Flow
Loading...
12
12
History and honest limits
History and honest limits
**Samuel P. Francisco** of Reading, Berks County, Pennsylvania, received US 6,544, dated 19 June 1849. His spindle passed through the tub's bottom in a water-tight bearing, stepped in a stirrup below, and was turned by a pulley and band from a hand wheel. He held that balling the butter saves "all those fine particles which in the ordinary process pass through the meshes of the strainer"; that is his claim. He claimed the tubulated disk dasher with a hollow stem, for churning with air and gathering the butter into balls.
**Honest limits.** We twist the stem by a bar from above instead of his band and hand wheel, so it turns well below the notebook's speed; a container and a printed disk stand in for his. FDM prints hold food in their layer lines, so wash well and replace when worn. Your times and weights are the result.
材料
7- 1 個プレースホルダー
- 1 個プレースホルダー
- 1 個プレースホルダー
- 1 個プレースホルダー
- 2000 mlプレースホルダー
- 1 個プレースホルダー
- 1 個プレースホルダー
必要な工具
8- プレースホルダー
- 1 vendor sell this, none ship to you yetプレースホルダー
- プレースホルダー
- プレースホルダー
- プレースホルダー
- プレースホルダー
- プレースホルダー
- プレースホルダー
設計ファイル
3この設計図で作るもの
関連ブループリント
これらのブループリントは知識を共有しています — 技術、材料、原理
CC0 パブリックドメイン
このブループリントはCC0で公開されています。許可を求めずに、自由にコピー、修正、配布、あらゆる目的で使用できます。
メイカーを応援するには、ブループリント経由で製品を購入してください。メイカーには メイカーコミッション がベンダーにより設定されています。または、このブループリントの新しいイテレーションを作成し、自分のブループリントにコネクションとして含めて収益を共有できます。